Magnavox MSD804 owner manual Quick Use Guide, Yes

1 Connections

Please refer to “Basic TV Connection” on the front page before you use this unit.

RF Output Channel

If channel 3 is already occupied for broadcasting,

1)Set your TV to channel 4.

2)Insert a pre-recorded tape into this unit.

3)Press the OUTPUT button on the DVD/VCR so that the VCR OUTPUT light is lit.

•If noise appears on the TV screen, press the VCR/TV button on the remote control.

4)Press the PLAY button once.

5)After a few seconds, press the PLAY button on the DVD/VCR for 3 sec- onds.

• The RF output channel will change

to channel 4 from channel 3 and you

will see a playback picture.

• When a picture does not appear on

Quick Use Guide

4 Turn on the unit for the first time

VCR

VCR

1

Turn on the TV and set it to channel 3.

•If channel 3 is already occupied for broadcasting, see“RF Output Channel” section.

2	POWER	Remote Control	TV Screen
		LANGUAGE SELECT
		B ENGLISH		[ON]
	or	FRANCAIS
		ESPAÑOL

5 Clock Set Up

VCR	VCR
1	-MENU-
MENU	TIMER PROGRAMMING
	AUTO REPEAT	[OFF]
	CHANNEL SET UP
	B CLOCK SET
	LANGUAGE SELECT
or	• If the clock is not set, the
	CLOCK SET screen
	appears when you press
	the MENU button. In this
	case, go to step [2].
2	CLOCK SET
or	MONTH DAY	YEAR
	0 3 / – –	– – – –
	HOUR MINUTE	AM/PM
	– – : – –	– –

Select the current month

the TV screen, repeat step [4].

6)Press the STOP button to stop play- back.

2	Installing the Batteries
	for the Remote Control
1	2	3

✄

3 VCR/DVD Switching

3		3		CLOCK SET
	CH 01		MONTH DAY		YEAR
		or	0 3	/ 1 5	– – – –
			HOUR MINUTE		AM/PM
AUTO SET UP			– –	: – –	– –

Select the current day

Do you connect the cable from the cable box or		4			CLOCK SET
the satellite box to the DVD/VCR’s ANT IN jack?				MONTH DAY			YEAR
YES
			or	0 3	/	1 5	2 0 0 4
Yes	Press the MENU
				– –	:	– –	– –
				HOUR MINUTE			AM/PM
	button to exit			Select the current year
	NO

			SUBTITLE/		POWER
			TIMER SET
			SETUP	AUDIO V.SURR ANGLE
			REC/OTR	REPEAT	REPEAT
					A-B
			SKIP/	C-RESET	SKIIP/
				CLEAR
		VCR button	CH		CH
			TOP MENU	MODE	RETURN
				DISPLAY
		DVD button	VCR		DVD
			MENU		ENTER
VCR	DVD
		DVD OUTPUT
		light	STOP		PLAY
				PAUSE
OUTPUT SELECT			NA509		SPEED
			1	2	3
		OUTPUT button			SLOW
			4	5	6
					VCR/TV
			7	8	9

SEARCH MODE

+10 0

VCR OUTPUT light

VCR MODE

Press the VCR button on the remote control.

(Verify that the VCR OUTPUT light is lit.)

DVD MODE

Press the DVD button on the remote control.

(Verify that the DVD OUTPUT light is lit.)

Note

•Pressing only the OUTPUT button on the front panel DOES NOT switch the mode of the remote control. You MUST select the correct mode on the remote control.

No Please wait for a few minutes.

After scanning...

•The tuner stops on the lowest memorized channel.

•You can select only the channels memo- rized in this unit by using the CHANNEL buttons.

5	CLOCK SET
MONTH DAY		YEAR
0 3	/ 1 5 MON 2 0 0 4
or
HOUR MINUTE		AM/PM
0 5	: – –	– –
Select the current hour
6	CLOCK SET
MONTH DAY		YEAR
0 3	/ 1 5 MON 2 0 0 4
or
HOUR MINUTE		AM/PM
0 5	: 4 0	– –
Select the current minute
7	CLOCK SET
MONTH DAY		YEAR
0 3	/ 1 5 MON 2 0 0 4
or
HOUR MINUTE		AM/PM
0 5	: 4 0	P M AM
		B PM

Select “AM” or “PM”

8To exit the CLOCK SET screen.

– 27 – EN