FUNAI DVC860D Playback Function, Normal Playback, Search Functions, Auto Repeat Playback

Page 18
INDEX SEARCH
03

PLAYBACK FUNCTION

NORMAL PLAYBACK

VCR

1Insert a prerecorded tape. The VCR will turn

on.

¡If the safety tab has been removed, the

VCR will start playback automatically.

2Turn on the TV and set the TV to channel 3.

¡If noise appears, change the RF output channel of the VCR to channel 4 by pressing PLAY for 3 seconds dur- ing playback. Then select the same channel (CH4) on your TV. (See “RF OUTPUT CHANNEL” on page 13 for the detail.)

3Begin playback by pressing PLAY.

¡Tracking adjustment will be done automatically (Digital Tracking function) when you start playback. To adjust the tracking manually, press SKIP/CH. on the remote or CHANNEL (o/p) on the VCR.

¡When a tape has reached the end, the VCR will rewind the tape to the beginning, and eject the tape.

4To stop playback, press STOP.

¡If no corresponding symbols appear on the display when you press buttons such as PLAY, RECORD,

Dor E, that means no cassette tape is in the VCR. Please insert a tape.

Counter Reset

¡You can reset the counter by pressing CLEAR/C.RESET on the remote control twice.

2Select "AUTO REPEAT" by pressing K or L.

3Begin auto repeat playback by pressing B so that ON appears next to "AUTO

REPEAT".

¡If the on-screen menu still remains, CLEAR/C.RESET to exit the menu.

¡To cancel the Auto repeat mode, press B at step [3] so that OFF appears next to "AUTO REPEAT".

SEARCH FUNCTIONS

VCR

PICTURE SEARCH

If you want to skip or repeat a scene during playback, press D or E.

¡Press it again and the VCR will now search at super high speed. (in the LP/SLP modes only).

INDEX SEARCH

An index mark will be assigned at the beginning of each recording you made. You may skip to a specific marked point by following the steps below.

1Press SEARCH MODE so that the Index Search menu appears.

2Enter the number of recordings you wish to

skip by pressing K or L within 30 seconds.

STILL/SLOW

You can freeze the picture on TV screen by pressing PAUSE during playback.

¡You can advance the picture one frame at a time by pressing PAUSE during the Still mode.

¡You cannot manually adjust the tracking of a still picture. However, if the picture begins to vibrate vertically during the still mode, you can stabilize the picture by pressing CHANNEL (o/p).

¡If the picture is distorted or rolling vertically, adjust the vertical hold control on your TV, if so equipped.

¡You can watch in the slow motion by pressing SLOW during playback or the still mode.

¡If a noise bar appears on the TV screen, you can reduce it by pressing CHANNEL (o/p).

¡After the VCR has been in Still/Slow mode for 5 minutes, it will stop automatically to protect the tape and the video head from damage.

¡To return to playback, press PLAY.

AUTO REPEAT PLAYBACK

VCR

This feature allows you to play a tape over and over.

1Select main menu by pressing MENU.

3Press B or { to start index search.

¡If you want to go in the forward direction, press B. ¡If you want to go in the reverse direction, press {. ¡If you want to stop search function, press STOP.

¡After index search, the VCR will play the tape auto- matically.

TIME SEARCH

This feature allows you to go to a specific point on a tape by entering the exact amount of time you wish to skip in order to reach the point.

1Press SEARCH-MODE so that the Time Search menu appears.

2 Enter your desired time to

TIME SEARCH

skip by pressing K or L

2 : 50

 

within 30 seconds.

 

3Press B or { to start time search.

¡If you want to go in the forward direction, press B. ¡If you want to go in the reverse direction, press {. ¡If you want to stop search function, press STOP.

¡After time search, the VCR will play the tape auto- matically.

– 18 –

EN

1L25

Image 18
Contents DVC860D Laser Safety Important Safeguards Supplied Accessories Symbols Used in this ManualAbout Copyright Table of Contents IndiceFeatures PrecautionsAbout the Discs Playable DiscsFollowing discs can be played back on this Operating Controls and Functions Display Button DVD mode Number Buttons DVD modeVCR mode Button DVD modeSKIP/CH. Buttons DVD mode Play Button DVD modePause Button DVD mode AC Power CordDisplay Displays During OperationLoading the Batteries VCR/DVD Switching DVD ModeHookups Connecting to a TV Without A/V TerminalsConnecting to a TV with A/V Terminals RF Output Channel for DVD/VCRFor TVs with S-VIDEO Input Jack Connecting to a Receiver with Dolby Digital Decoder Connecting to AN Analog Audio SystemTo Preset the Channels Again SetupAutomatic Channel SET UP To Select a Desired ChannelClock SET UP To Change the ON-SCREEN LanguageTo ADD/DELETE Channels Search Functions Playback FunctionNormal Playback Auto Repeat PlaybackNormal Recording Timer RecordingRecording Function Before recording, make sureTo CHECK, CORRECT, or Cancel AN Automatic Timer Program Hints for TimerTo Stop AN Automatic Timer PRO- Gram Already Started Press STOP/EJECT on the DVD /VCR CombinaTo Monitor the Recording Special FeaturesCopying a Video Tape You can not copy a DVD to a videotapeAuto Rewind General FeaturesPlaying a Disc Basic PlaybackStep by Step Playback Disc MenuTitle Menu Fast FORWARD/REVERSE SearchTitle / Chapter Search ZoomTrack Time SearchRepeat Track RepeatRepeat Title / Chapter Repeat A-BON-SCREEN Information Random PlaybackMP3 Playback Track SelectionProgram Stereo Sound ModeSubtitle Language Audio LanguageParental Level Changing the ON-SCREEN DisplayParental Control ¡The elapsed and remaining Playing time of the currentDVD Setup Marker Setup ScreenAudio Setting ¡Be sure to press SETUP, or the setting will not work Black Level SettingDisplay Setting Virtual SurroundLanguage Setting Troubleshooting Guide Problem Corrective ActionMaintenance ServicingSpecifications Controles DEL Funcionamiento Y SUS Funciones Panel DelanteroBotón Play DVD Sólo DVD Botón VCRCambio DE VCR/DVD Modo VCRConexiones PreparaciónReproduciendo UN DVD Video O UN CD Audio Reproducción DE UN DiscoPreparación DE Reloj Para empezarMemo Memo Memo 0VMN03452 H9400UD