LG Electronics 37LD325H, 37LD340H Clone Programmer Troubleshooting, Master and Target TVs

Page 161

Troubleshooting (Cont.)

Clone Programmer Troubleshooting

Warning: Do not connect a clone programmer to a PPV card installed in the Master or Target TVs. Also, if the TV is in LodgeNet PPV Mode (check

with the site administrator if you are not certain), do not connect a clone programmer to the GAME CONTROL/ MPI port. Either of these actions will damage the clone programmer and, if applicable, the PPV card.

Reset Clone Programmer After Static Shock

After replacing exhausted batteries (LT2002 only), or if the clone programmer behaves strangely after a static shock:

TLL-1100A: Turn the TLL-1100A OFF and then ON.

LT2002: Use a paper clip or similar instrument inserted through the small hole marked RESET to activate the internal reset switch and restore normal operation.

After a reset, check the real-time clock setting. It may be nec- essary to set the clone programmer clock from a TV contain- ing the correct time.

Notes

The TLL-1100A and LT2002 clone programmers are designed to be used with TVs containing the 221-01006 and later pro- cessors. Use with earlier TVs may give unpredictable results. Processors used before the 221-01006-04 have a limited screen display capability; they cannot display entire screens as shown in the setup instructions accompanying the clone programmer. Use the printed menu illustrations in the docu- mentation as an aid to making your programming choices.

For both Master and Target TVs—The TV EBL must be in Pass-through Mode for cloning purposes. See also IMPORTANT CLONING INFORMATION on page 27.

Symptom

Possible Cause(s)

Possible Solution(s)

Clone Programmer

 

 

Clone copies setup in less than 30 seconds.

Not enough time to copy entire TV setup.

TLL-1100A: Turn the TLL-1100A Off and then ON.

LT2002: Press RESET on clone programmer.

Then redo Learn/Teach. (Learning usually takes about 90 sec- onds; Teaching usually takes 3 to 4 minutes.)

Remote does not operate clone programmer.

Clone menu does not dis- play on TV screen, TLL- 1100A shows error mes- sage, or LT2002 LED does not blink.

Clone menu hard to read. No time set.

Clone not working.

Clone scans channels more than once.

Wrong Installer Remote.

MPI cord not connected. TV not turned ON.

(LT2002 only) Weak batteries. (TLL-1100A only) No charge. Weak signal.

Time not available.

Clone programmer problem.

Clone should only scan channels once.

Only use an LG Installer Remote to operate clone programmer with TV.

Connect MPI cord properly, and ensure good connection. TV must be powered ON for clone programmer to work. Install four (4) fresh AA high-quality alkaline batteries.

Ensure the TLL-1100A is fully charged or connected to AC power. Connect TV to a reliable analog channel signal source.

Set time on a TV, and copy time to clone programmer.

Try a different clone programmer.

Reset the clone programmer.

Ensure TV is set up correctly, and try cloning again.

Master and Target TVs

Cloning did not work.

Procedure interrupted.

Wait until procedure complete message is displayed.

 

Different TV models.

Cloning is only possible with identical model TVs.

 

Step(s) omitted or not per-

Refer to the applicable cloning procedure(s), and make sure all

 

formed.

tasks were performed.

(LT2002 only) Clone time

Batteries were removed.

Batteries must remain installed to retain time settings.

disappeared.

 

 

New setup not present.

Target TV not reset.

Disconnect Target TV from AC power for fifteen (15) seconds.

After cloning operations are complete, unplug the TLL-1100A/LT2002 from the TV.

If the TV does not display a picture (blank screen) after a few seconds, just change channels.

44

206-4163

Image 161
Contents LCD TV Class B digital device FCC NoticeNot to install the TV by the hanging power Important Safety InstructionsMoving CleaningOutdoor antenna grounding NEC National Electrical CodeDot Defect Only Hg lamp used LCD TVGenerated Sound For LED LCD TV/ LCD TVContents Set Password & Lock System Clock Setting100 101Some of these features are not available on all models Feature of this TVAccessories Front Panel Information 32/37/42LD320H, 32/37LD325H Back Panel Information32/37LD310H AV Audio/Video Power Cord SocketM4 x Stand InstructionsProtection Cover 200 Vesa Wall MountingCable Management Kensington Security System Desktop Pedestal InstallationSwivel Stand Attaching the TV to a Desk Stand Screws 32/37LD310H, 32/37LD330HPreparation Antenna Analog or Digital Antenna or Cable ConnectionComponent Connection HD Receiver SetupHdmi Connection Connect the DVI output of the digital set-top DVI to Hdmi ConnectionBox to the HDMI/DVI in 1 jack on the TV Connect the digital set-top box audio output toComponent in Audio jacks on the TV DVD SetupComponent Input ports RJP Composite RCA ConnectionAntenna Connection VCR SetupRemote control TV using the Input button onCamcorder Select the AV1 or AV2 input source onUSB Connection After connecting the USB in jack, youConnect the USB device to the USB Jack on the side of TVVGA D-Sub 15 Pin Connection PC SetupConnect the DVI output of the PC to Input button on the remote controlConnect the PC audio output to the Audio HDMI/DVI in 1 jack on the TVSupported Display Specifications RGB-PC, HDMI-PC Select Resolution Screen Setup for PC modeSelect the desired resolution Select PictureStart Auto Configuration Select Auto ConfigSelect Yes Select Screen RGB-PCSelect Position, Size, or Phase Adjustment for screen Position, Size, and PhaseSelect Picture Select ResetStart Reset Watching TV / Channel Control Remote Control FunctionsColor Access special functions in some menus Volume Adjusts the volumeVCR/DVD Control video cassette recorders or DVD players Eject Eject the USB device Ratio Change the aspect ratioFirst, connect power cord correctly Volume AdjustmentAt this moment, the TV switches to standby mode Turning on the TVSelect a menu item ON-SCREEN Menus SelectionAccept the current selection Return to TV viewingFor LD340H, LD345H, LD330H series For LD320H, LD325H, LD310H seriesPicture Test / Sound Test Customer SupportRED Select Customer Support Return to the previous menu Return to TV viewingSelect Customer Support Product/Service InfoReturn to TV viewing Return to the previous menuAuto Scan Auto Tuning Channel SetupSelect Auto Tuning Run Auto tuningSelect Manual Tuning Add/Delete Channel Manual TuningMove the pages when the channel list is Switch to the chosen channel numberChannel Editing Menu Select ChannelSelect the desired input source Input ListExample Electronic Program Guide Select Channel Label Channel LabelDemo Mode USB Connection Connection MethodPrecautions when using the USB device Or Extra Contents Entry ModeSelect MY Media This TV can view JPG image files or play MP3 audio filesScreen Components Photo ListOn-Screen Display on your model may be slightly different Supported photo file *.JPGPhoto Selection Mark ModeSelect the target folder or drive More operations are available in full screen modeSelect the desired photos Selected photo is displayed in full sizeOption Set values for Slide Speed and Music Album Select the SlideshowBGM, Rotate Zoom In, Option, or Hide Select Set Photo View , Set Video , or Using the Photo List FunctionEnter Set Audio Select Slide Speed or BGMSelect Sound Mode, Auto Volume, Clear Voice II, or Balance Select Picture ModeSelect Music List Music ListMove to Photo List Music file Music SelectionMusic files are played Use the CH ꕌꕍ button to navigate in the musicSelect Set Audio Play or Set Audio Using the Music List FunctionShow the Option menu Voice II , or Balance Select Repeat or RandomExtra Contents Select the desired picture format Picture Size Aspect Ratio ControlSelect Aspect Ratio Just Scan 169Set By Program ZoomOr Game Return to the previous menu Return to TV viewing Preset Picture Settings Picture ModeSelect Picture Mode Select Vivid, Standard, Cinema, Sport Manual Picture Adjustment User Mode Select Advanced Control Picture Improvement Technology Advanced ControlAdvanced Control This is produces richer colors Signal is inputted through HdmiInitialize the adjusted value Picture ResetSelect Picture Reset Menu Select PictureSelect Audio Auto VolumeSelect Auto Volume Select Level Make appropriate adjustments Adjustment for Clear Voice Level with selecting OnClear Voice Menu Select AudioBalance Sound & Language ControlPreset Sound Settings Sound Mode Adjust the sound to suit your taste and room situations Sound Setting Adjustment User ModeTV Speakers ON/OFF Setup Audio ResetSelect Reset Return to TV viewing Select TV SpeakerAudio Language This feature operates only in DTV/Cable DTV modeSelect Option Select Language Select Audio LanguageSelect Menu Language ON-SCREEN Menus Language SelectionMenus can be shown on the screen in the selected language Analog Broadcasting System Captions Caption ModeSelect CC1-4 or Text1-4 CaptionDigital Broadcasting System Captions Select CC1-4,Text1-4, or Service1 Select Digital Option Caption OptionAuto Clock Setup Clock SettingManual Clock Setup Time SettingSelect Repeat Auto ON/OFF Time SettingMon.~Sat. , Sat.~ Sun. , or Sun Select and set Hour or MinuteAuto SHUT-OFF Setting Sleep Timer SettingSelect Sleep Timer Select Auto OffSetting up Your Password SET Password & Lock SystemChange the password by inputting a new password twice Set PasswordEnter Select Lock Input the password Select Set Password Choose any 4 digits for your newSelect Lock System Lock SystemSelect Block Channel Channel BlockingSelect Movie Rating Movie & TV RatingMovie Rating Mpaa Select Lock TV Rating ChildrenSelect TV Rating-Children Select Age or Fantasy Violence TV Rating General Select Downloadable Rating Downloadable RatingSelect Input Block Enables you to block an inputExternal Input Blocking Install new batteries TroubleshootingTry another channel. The problem may be with the broadcast Directly at the TVUse normal MP3 file No output from one Adjust Balance in menu optionAppendix MaintenanceModels Product SpecificationsCode Function IR CodeVersion 2, June Open Source License104 105 106 GNU Lesser General Public License 108 109 110 111 Mozilla Public License 113 114 115 116 Model Serial Copyright 2011, LG Electronics U.S.A., Inc 206-4163 Rev BFor Customer Support/Service, please call­ Important Safety Instructions Outdoor Antenna Grounding Table of Contents Commercial Mode Setup Overview Setup Checklist / OverviewSetup Checklist Channel Guide ProCentric TV Interactive Menu FeaturesInformation Remote HelpAUDIO/VIDEO LD320H/LD325H Rear Jack PanelSide Connections Panel Side Connections Panel / RF Antenna & MPI ConnectionsRF Antenna & MPI Connections 2 InputCloning Installer OverviewInstaller Remote Flashbk Flashback Installer Remote Control Typical Key FunctionsSet up TV features Commercial Mode Setup for Master TVSet Installer Menu items Lock the channel lineup Run Auto Tuning Channel SearchVerify the TV setup Accessing the Installer Menu Installer MenuUsing the Installer Menu Exiting the Installer Menu and Activating UpdatesBrief Description of Function and Comments Installer Menu Items 000 throughCH not Avble Installer Menu Items 073 throughInstaller Sequence Detailed Descriptions of Installer Menu ItemsSleep Timer AUX Status Procentric TV Setup Menus Overview To perform channel editing/labeling Editing/Adding Channel Icons and/or LabelsFTG Configuration Overview FTG Mode of OperationConfiguration Application manual for further information Delete Installer Defaults FTG Installer Menu Configuration Utility OverviewBefore you begin cloning Cloning Overview / Clonable Menu FeaturesClonable Menu Features Learn Setup from Master TV Cloning ProceduresTeach Master TV Setup to Target TV USB Cloning NotesOr Catv TLL-1100A Cloning NotesOptional Set the Clock LT2002 Clone Programmer LT2002 Cloning NotesFrom previous TV Connections Remote Jack Pack / TV Connections & SetupRemote Jack Pack Setup Upgrading TV/PTC Software Checking the Software VersionsDownloading a Splash Screen Image Splash Screen Image File GuidelinesStatic Reference Power Consumption SettingsCamport Side Video Functionality Control Reference TV Camport Auto Sense OperationCamport Operation Stand-alone Camport Operation FTG or PPVEnable Reference TV Aux Input ConfigurationLAN Power 001 Default Off 007 Reference b-LAN Setup & OverviewTV Standby State TV Power On State RJP Input Auto-sensing Hierarchy Priority Video Audio Reference RJP Model List and Input Auto-sensing HierarchyRJP Model List Legacy Models Scaler Models General Troubleshooting TroubleshootingController Quick Check Troubleshooting Flow ChartSymptom Possible Causes Solutions Commercial Mode Check / FTG Operation TroubleshootingFTG Operation Troubleshooting Reset Clone Programmer After Static Shock Clone Programmer TroubleshootingSymptom Possible Causes Possible Solutions Clone Programmer Master and Target TVsOHM RF Cable Glossary of TermsDate Description Document Revision History / NotesDocument Revision History For Customer Support/Service, please call­ Copyright 2011, LG Electronics U.S.A., Inc 206-4177 Rev aPower Cord Polarization 206-4177 For products where thermal deformation is required Adding Channel Icons / Custom Channel Labels Setup Checklist / Commercial Mode Setup Overview ProCentric TV Interactive Menu Features RGB in PC Connection for RGB output from PC LD310H Rear Jack PanelAntenna Or Catv 206-4177 Returns one level to the previous menu/ display Fact Default Channel Changing Installer Menu Settings Navigation within the Installer MenuInstaller Menu Items 000 through 091 YPrPb2 EN Set to 1 to enable Hdmi 2 input 094 Detailed Descriptions of Installer Menu Items Sleep Timer = Black = Cyan Back Lighting TV Setup Menus Overview Enter the TV Installer Menu Press Menu repeatedly Cloning Overview / Clonable Menu Features Updating TLL-1100A Cloning Notes Optional Set the Clock Cable, poor contacts, or other From previous Determining the TV Operating Mode FTG Mode Overview / Determining the TV Operating ModeFTG Mode of Operation Learning an FMA Configuration File from a TV Optional Manual Configuration / Setup for a TV FTG Channel Map Configuration Utility Overview FTG Channel Map Editor Overview FTG Installer Menu Configuration Utility Overview FMA Configuration Utility Overview V1.00.001 Splash Screen Image File Guidelines 32LD310H 37LD310H Power Reference TV Camport Auto Sense Operation Reference TV Aux Input Configuration Troubleshooting End Bad PPV Card Leave the TV set on Bad Go to Installer Menu Clone Programmer Troubleshooting Glossary of Terms Date Description January Revision a New Document For Customer Support/Service, please call 206-4186 Rev a 206-4186 Important Safety Instructions Outdoor Antenna Grounding Table of Contents Commercial Mode Setup Overview Setup Checklist / OverviewSetup Checklist Help AUDIO/VIDEO LD340H/LD345H Rear Jack Panel2 Input Side Connections Panel / RF Antenna ConnectionSide Connections Panel XxLD340H PTC Installer Menu 000 Number Buttons 0 9 & Dash Set Installer Menu items Commercial Mode Setup for Master TVSet up TV features Run Auto Tuning Channel SearchLock the channel lineup Verify the TV setupAccessing the Installer Menu Installer MenuUsing the Installer Menu Exiting the Installer Menu and Activating UpdatesBrief Description of Function and Comments Installer Menu Items 000 throughCH not Avble Installer Menu Items 073 throughInstaller Sequence Detailed Descriptions of Installer Menu ItemsSleep Timer AUX Status Procentric TV Setup Menus Overview To perform channel editing/labeling Editing/Adding Channel Icons and/or LabelsBefore you begin cloning Cloning Overview / Clonable Menu FeaturesClonable Menu Features Learn Setup from Master TV Cloning ProceduresTeach Master TV Setup to Target TV USB Cloning NotesOr Catv TLL-1100A Cloning Notes7-6 + Enter Optional Set the ClockLT2002 Clone Programmer LT2002 Cloning NotesFrom previous FTG Mode via CPU or EBL FTG Mode of Operation OverviewAspect Ratio Determining the TV Operating ModeFTG Mode via CPU Teaching FMA Configuration to a TV Learning an FMA Configuration File from a TV Optional Manual Configuration / Setup for a TV FTG Mode via EBL FTG Channel Map Configuration Utility FTG Configuration Application Utilities OverviewFTG Channel Map Editor UpdateInstaller Defaults FTG Installer Menu Configuration UtilityFMA Configuration Utility TV Connections Remote Jack Pack / TV Connections & SetupRemote Jack Pack Setup Upgrading TV/PTC Software Checking the Software VersionsDownloading a Splash Screen Image Splash Screen Image File GuidelinesStatic Reference Power Consumption SettingsCamport Side Video Functionality Control Reference TV Camport Auto Sense OperationCamport Operation Stand-alone Camport Operation FTG or PPVEnable Reference TV Aux Input ConfigurationLAN Power 001 Default Off Reference b-LAN Setup & OverviewTV Standby State TV Power On State RJP Input Auto-sensing Hierarchy Priority Video Audio Reference RJP Model List and Input Auto-sensing HierarchyRJP Model List Legacy Models Scaler Models FTG Mode via EBL Resetting a TV to Pass-through ModeFTG Mode via CPU General Troubleshooting TroubleshootingController Quick Check Troubleshooting Flow ChartSymptom Possible Causes Solutions Commercial Mode Check / FTG Operation TroubleshootingFTG Operation Troubleshooting Master and Target TVs Clone Programmer TroubleshootingSymptom Possible Causes Possible Solutions Clone Programmer OHM RF Cable Glossary of TermsDate Description May Revision a New document Document Revision History / NotesDocument Revision History For Customer Support/Service, please call­
Related manuals
Manual 59 pages 59.38 Kb Manual 50 pages 29.7 Kb

26LD340H, 42LD320H, 37LD325H, 37LD310H, 42LD340H specifications

LG Electronics has established itself as a formidable name in the realm of consumer electronics, particularly in the television sector. Among its popular offerings are the models 26LD320H, 37LD345H, 32LD325H, 26LD345H, and 37LD340H. These models combine sophisticated technology with user-friendly features, catering to a diverse range of viewing preferences.

Starting with the 26LD320H, this compact LCD TV showcases a 26-inch screen, making it ideal for smaller living spaces or bedrooms. Its native resolution of 1366 x 768 pixels provides a crisp display, enhancing the viewing experience for standard-definition content and HD broadcasts. The TV features LG's Intelligent Sensor technology, which automatically adjusts picture settings based on surrounding light conditions, ensuring optimal brightness and color balance at all times.

Moving on to the 37LD345H, this model boasts a larger 37-inch display, perfect for living rooms and entertainment areas. With a resolution of 1920 x 1080 pixels, viewers can enjoy full HD content with enhanced clarity and detail. The 37LD345H is equipped with a built-in digital tuner, allowing viewers to access over-the-air HD broadcasts without the need for additional equipment. The TV also supports multiple HDMI inputs, making it easy to connect gaming consoles, Blu-ray players, and other devices.

The LG 32LD325H serves as a versatile option with its 32-inch screen, offering a balance of size and performance. This model supports both standard and high-definition content, resulting in a vivid picture quality that enchants viewers. The 32LD325H incorporates LG’s unique Picture Wizard technology, enabling users to fine-tune picture settings for their specific viewing environment.

The 26LD345H mirrors the innovative features of LG’s lineup with its stylish design and engaging 26-inch screen. It supports various input options including USB and HDMI, allowing users to connect to their favorite media devices seamlessly. Additionally, the inclusion of a robust sound system enhances the audio experience, making it a solid choice for video content and music alike.

Lastly, the 37LD340H offers an impressive 37-inch display and a similar set of features as its counterparts, appealing to those seeking a larger screen without compromising on quality. It is designed with full HD resolution and advanced sound capabilities to deliver an immersive viewing experience.

In summary, the LG Electronics series of televisions from the models 26LD320H, 37LD345H, 32LD325H, 26LD345H, to the 37LD340H, provides an array of options benefiting from modern technologies and stylish designs. They not only cater to varied room sizes and viewing needs but also ensure that consumers experience high-quality visuals and sound, aligning with LG's commitment to innovation and customer satisfaction.