LG Electronics 32LS5600/560S/560T-ZC, 32LS5610/561T-ZA E. Noise, Lcd Tv, Identify nose type

Page 54
E. Noise

Standard Repair Process

 

 

Error

E. Noise

Established

2012. 01 .14

 

 

 

LCD TV

date

 

 

 

symptom

Circuit noise, mechanical noise

Revised date

 

13/14

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Identify nose type

Circuit noise

Mechanical noise

Check location of noise

Check location of noise

Replace PSU (with LED driver)

OR

Replace LED driver

Mechanical noise is a natural phenomenon, and apply the 1st level description. When the customer does not agree, apply the process by stage.

Describe the basis of the description in “Part related to nose” in the Owner’s Manual.

OR

When the nose is severe, replace the module (For models with fix information, upgrade the S/W or provide the description)

If there is a “Tak Tak” noise from the cabinet, refer to the KMS fix information and then proceed as shown in the solution manual (For models without any fix information, provide the description)

Copyright © 2012 LG Electronics. Inc. All rights reserved.

LGE Internal Use Only

Only for training and service purposes

 

Image 54
Contents READ THE SAFETY PRECAUTIONS IN THIS MANUAL CHASSIS LD21BSERVICE MANUAL http//aic.lgservice.comSERVICING PRECAUTIONS CONTENTSSAFETY PRECAUTIONS SPECIFICATIONSAFETY PRECAUTIONS IMPORTANT SAFETY NOTICESERVICING PRECAUTIONS Electrostatically Sensitive ES DevicesSmall-Signal Discrete Transistor Removal/Replacement IC Remove/ReplacementReplacement Removal1. Application range SPECIFICATION4. Model General Specification 3. Test methodDVB-S2 8PSK / QPSK 2 ~ 45Msymbol/s Symbolrate 4.0Msymbols/s to 7.2Msymbols/ssymbolrate DVB-S QPSK 2 ~ 45Msymbol/s5. Video resolutions 2D 5.1. Component Input Y, CB/PB, CR/PR5.2. RGB Input PC - LS35/LS34/CS46 series models are not supported 5.3. HDMI InputPC/DTV PCDVI1. Application Range ADJUSTMENT INSTRUCTIONBoot file Download 2. Designation3.2. EDID Download 3.1. ADC Process3.3. EDID data 7. ADC Calibration4. Total Assembly line process 4.1. Adjustment Preparation3.4 Function Check 5. HI-POT Test 4.3. Outgoing condition Configuration6.1. Signal Table 6. Model name & Serial number D/L7.1 MAC Address 7. MAC Address & CI+ key download6.3. Method & notice GP4LOW7.2 LAN Inspection 7.3. LAN PORT INSPECTIONPING TESTח ͷͲͳͤͤͤͪͥͣ͢͡ ͙;ͤ͛ͽͥͦ͑͟͝ͳͼ͑͝;ΒΔΙΚΟΖ͚ ח ͣ͢ͶͲ SCREW ASSEMBLY WORKING GUIDEScrew specification and application situation ח ͷͲͳͤͨͩͩͣ͑͢͡͡ ͙;ͧ͛ͽ͑͢͡͝ͳͼ͑͝;ΒΔΙΚΟΖ͚LG2111 A RearSide IC101TDSN Applied Model **LM580T, **560T, **LS350T, **CS460TLS350T/CS460T G301D560S, **LS350S, **CS460S LS350S/CS460SG001D EXPLODED VIEW to delete CI or gate for GP4LS7LR22011.12.01Copyright 2012 LG Electronics. Inc. All rights reserved for SYSTEM EEPROMNormal Normal PowerVDDC DDR3+3.3VNormal FROM LIPS & POWER B/DPowerDET +1.5VDDRIR/LED and control for normal models USB SIDE USB1DIODESUSB2DIODES HDMI SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION RGB-PC / SPDIFTHE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF ISRS-232C COMMERCIAL/NonOS MODEL OPTION COMMERCIAL MODEL OPTIONFor Comsumer model, use 4PIN Wafer LVDS for large inch IC1201 S7LR2DIVXMS10GP4LS7LR22011/06/03 DDR25612 H5TQ1G63DFR-H9CSerial Flash for SPI boot SFLASHMAINMACRONIXSFLASHMAINWINBOND IC1401-*1 W25Q80BVSSIG Headphone *Option HEADPHONE PHONEHEAD CI Region Option name of this page CISLOT because of Hong Kong10067972-0500LF H/W option ETHERNET GP4LS7LR22011/06/14 ETHERNET21ETHERNET TU2601 GP4RGLOBALTUNERBLOCKTU2602TU2603 TDSS-G101D TDSN-G301D TDSQ-G001DGP4LS7LR22011/11/02 DVBS27 DVB-S2 LNB Part AllegroOptionLNB DCDCGND and AGND are connectedJK2801 SCART / COMPONENT&COMPSITFULL SCART / COMPONENT1 PSC008-01AUDIO AMPSTA380BWE Page Contents of LCD TV Standard Repair Process Error symptom Contents of LCD TV Standard Repair Process Detail Technical ManualContinue to the next page ContentMain B/D↔ Power B/D, LVDS Cable,Speaker Cable,IR B/D Cable A. Video errorLCD TV A2 Check Power Board 24v outputBoard 3.5V,12V,20V voltages of PowerCheck various or 24V…By using Digital signal level meter By using Diagnostics menu on OSD Menu→ Set up→ Support → Signal Test Signal strength Normal over 50%Signal Quality Normal over 50% → Set-Top-Box, Different maker TV etc ※ Check A8/ A9Check color by input -External Input COMPONENT -RGB Link CableConnect other external device and cable External device screen error-Color errorVertical/Horizontal bar, residual image, light spot Check color condition by input -External Input -Component RGBCheck Power On ‘”High” B. Power errorCheck Power LED Measure voltage of each output of Power B/DPOWEROFFABNORMAL1 Check Power Off ModeIf Power Off mode is not displayed Check Power B/D voltage POWEROFFCPUABNORMALCheck user menu Speaker off C. Audio error24V of Power Check audio B+In case of External Input signal error Check and fix external device Check audio B+ VoltageD. Function error 1. Remote controlR/C operating errorCheck & Repair Recognition error Check input signalY Check technical Signal information input? - Fix information Replace Main B/DE. Noise Identify nose typeF. Exterior defect