LG Electronics 50PN6500 YyGrounding, YyANTENNAS Outdoor Antenna Grounding Can differ by country

Page 4

4IMPORTANT SAFETY INSTRUCTIONS

ENGLISH

yyGrounding

(Except for devices which are not grounded.) Ensure that you connect the earth ground wire to prevent possible electric shock (i.e. a TV with a three-prong grounded AC plug must be connected to a three-prong grounded AC outlet). If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.

Power Supply

Short-circuit

Breaker

yyAs long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if the unit is turned off.

yyDo not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product.

yyANTENNAS Outdoor Antenna Grounding (Can differ by country):

If an outdoor antenna is installed, follow the precautions below. An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits as death or serious injury can occur. Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code (NEC) in the U.S.A. provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding electrode.

Antenna grounding according to the National Electrical Code, ANSI/NFPA 70

yyCleaning

When cleaning, unplug the power cord and wipe gently with a soft cloth to prevent scratching. Do not spray water or other liquids directly on the TV as electric shock may occur. Do not clean with chemicals such as alcohol, thinners or benzine.

yyMoving

Make sure the product is turned off, unplugged and all cables have been removed. It may take 2 or more people to carry larger TVs. Do not press or put stress on the front panel of the TV.

yyVentilation

Install your TV where there is proper ventilation. Do not install in a confined space such as a bookcase. Do not cover the product with cloth or other materials while plugged. Do not install in excessively dusty places.

yyIf you smell smoke or other odors coming from the TV, unplug the power cord and contact an authorized service center.

yyDo not press strongly upon the panel with a hand or a sharp object such as a nail, pencil or pen, or make a scratch on it.

yyNever touch this apparatus or antenna during a thunder or lightning storm.

yyWhen mounting a TV on the wall, make sure not to install the TV by hanging the power and signal cables on the back of the TV.

yyDo not allow an impact shock or any objects to fall into the product, and do not drop anything onto the screen.

yyDisconnecting the Main Power

Mains plug is the disconnecting device. The plug must remain readily operable.

yyStore the accessories (battery, etc.) in a safe location out of the reach of children.

yyThis apparatus use batteries. In your community there might be regulations that require you

to dispose of these batteries properly due to environmental considerations. Please contact your local authorities for disposal or recycling information.

yyDo not dispose of batteries in a fire.

Ground Clamp

Electric Service Equipment

Ground Clamp

Antenna Lead in Wire

Antenna Discharge Unit

(NEC Section 810-20)

Grounding Conductor

(NEC Section 810-21)

Power Service Grounding

NEC: National Electrical Code Electrode System

(NEC Art 250, Part H)

yyDo not short circuit, disassemble or allow the batteries to overheat.

Image 4
Contents Plasma TV Important Safety Instructions EnglishEnglish YyDisconnecting the Main Power YyGroundingYyANTENNAS Outdoor Antenna Grounding Can differ by country YyMovingPreventing Image burn or Burn-in on your TV ScreenYyDot Defect For USA and Canada YyGenerated SoundLicenses Table of Contents Assembling and Preparing Protection Cover Power Cord holder Stand Body, Stand BaseUnpacking To an External device To the TV To a wall plug to the TVFerrite core Parts and buttons Button DescriptionAdditional information of the manual Lifting and moving the TVSetting up the TV Attaching the standTo detach the stand For 50PN4500, 50PN5300, 50PN6500Mounting on a table Mounting on a wall OptionalTidying cables Copper wire Connecting to an antenna or cableMaking Connections Connecting to a HD receiver, DVD Player or VCR Hdmi ConnectionDVI to Hdmi Connection Hdmi is the best way to connect a deviceComponent Connection Composite Connection Yellow White REDHdmi Connection or DVI to Hdmi Connection Connecting to a PCChoose method a or B to make connection Not Provided Connecting to an Audio System Digital Optical Audio ConnectionConnecting a USB Device Number button Remote ControlLIST, Dash VOL CH v,OK ꔉ BackWatching TV Language Mode Setting Time Setting Auto TuningTurning the TV on for the first time Troubleshooting Problem SolutionExternal Control Device Setup Specifications 42PN4500 50PN450050PN5300 60PN5300 50PN6500 60PN6500Child Safety LG Customer Information Center External Control Device Setup This feature is not available for all models Volume +Volume PowerExternal Control Device Setup USB TypeSerial port RS-232CSub Communication Parameters Space Ascii code ‘0x20’ Carriage Return Ascii code ‘0x0D’Set ID C8 Step 0F Step Volume Mute Command k e Aspect Ratio Command k c Main Picture SizeVolume Control Command k f Contrast Command k gTint Command k j ColorColour Temperature Command x uSharpness Command k k OSD Select Command k lColombia Model For South Korea, North/Latin America exceptFor Japan Model ChannelProgramme Add/DelSkip Command m b Control Back Light Command m gControl Panel Light Command m g For Plasma TV Input select Command x b Main Picture InputExtended 3DCommand x v only 3D models Depending on model DCommand x t only 3D models Depending on modelDon’t care