Q-See QSDT8PCRC manual Introduction, Summarization

Page 5

Error! Use the Home tab to apply
1 to the text that you want to
appear here. Error! Use the Home
tab to apply	1 to the text that

SuperDVR & QSDT8PCRC Cards		you want to appear here.
	1 Introduction
	标题	标题
User Manual

1.1 Summarization

Thank you for choosing our digital video capture cards.

The QSDT8PCRC 8 Channel cards use software H.264 compression format, and enable a maximum of 16 channels real-time surveillance in CIF resolution. Our cards are mature and cost-effective products that should be your ideal choices. They enable synchronous audio and video compression and transmission along with their powerful compression rate and network transmission function. They are widely used in banks, intelligent communities, traffic management units, medical systems, educational systems, armed forces and so on.

This manual is suitable for SuperDVR 6.3, which supports QSDT8PCRC cards.

In this manual, you will learn how to install the hardware and driver (software), and how to setup the systems on this range of products. Please make sure your operations with the products are strictly in accordance with the manual, to maintain the stability of the digital surveillance systems.

The following are standard functions of these products:

•Schedule record mode

Users can choose any period in a day to record and set up record modes, i.e. sensor alarm record, motion detection record, manual record, Schedule Record.

•Motion detection mode

Motion detection areas are adjustable with a maximum 16 areas for each channel. Users can also set motion detection sensitivity for each channel. The system begins to record only when motion is detected is detected on the channel and after motion stops it will stop recording after a certain time period, which is adjustable by users.

•Sensor alarm record mode

The system has an external alarm which enables the system to support alarm input and output.

•Recycling record mode

Users can set recording storage sequence for HDD partitions. The recording storage will automatically switch to the next partition when the current one is full. If all the partitions are full and recycling record mode is enabled, the oldest recorded data will be covered by new data. Users can also set HDD minimum storage alarm. Then once the present storage space is less then the minimum storage and recycling record mode is not

5

Image 5

Contents Page Contents Delete Recorded Files Capture Pictures Image Zoom in/out Appendix1Appendix3 Function Tree Appendix2 Quick Start for UsingAppendix 4.3 IE Client FunctionTree Appendix 4.4 Remote Playback Function TreeSummarization IntroductionTo the text that You want to appear here System Requirements Card SpecificationsQSDT8PCRC Card Hardware Hardware InstallationQSDT8PCRC Video Capture Card Hardware Installation Video Capture Card HardwareSuperDVR & QSDT8PCRC Alarm Board HardwareConnect Audio Signal Install Video Capture Card DriverH.264 Series Video Capture Card Installation Interface Select Video Format Install driver firstClick ‘Finish’ Click ‘Next’SuperDVR & QSDT8PCRC Cards Display Control Panel Main Display InterfaceDisplay Control Panel Display ModesClick , system will be record and save all the cameras LoginUrgent Record Record Modes Record SetupRecord Record Status Panel Camera SecurityRecord Quality Select recording image quality here Audio Motion Detection Record Mode An alarm output Manual Record ModeSensor Alarm Record Mode Please refer to ‘5.4 Schedule Configuration’ for details Configuration’. The dark green lightSchedule Recording Recycling RecordingsTo enter the main setup interface System SetupBasic Configuration Call Monitor ResolutionCaption Video Configuration Click and enter the Motion Detection Configuration Motion Detection ConfigurationBy clicking ‘Clear’, you can clear all the selected areas Set Motion Detection AreaClear Motion Detection Area Schedule Configuration Schedule ConfigurationAlarm Triggering Conditions Configuration Motion Detection Alarm ConfigurationSystem can receive alarms from both local place and network Local Alarm Record Triggering ConfigurationAlarm Output Alarm RecordAuto Mail Function Motion 2 Motion 16 32CH card has maximum 16 motion alarms12 Auto Mail Setup Interface Edit Map Map Configuration15 E-Map Edit View Map16 View Cameras Protocol Setup P. .Z Control ConfigurationClick Enter PTZ Configuration Parity Odd and even parity bit, default None Serial Ports SetupAddress Communication address of P.T.Z device ID number Set corresponding parameters in the area belowChange User rights Users ConfigurationClick To access the User’s Configuration area Delete User Administrator this user hasAdd User SuperDVR & QSDT8PCRC Cards Click Access the P.T.Z control areaCamera Speed AdjustmentSuperDVR & QSDT8PCRC Click To set Preset point Change Preset point name. EveryPress and return to the live surveillance status Access the following areasPlaying Back and Control Record SearchSuperDVR & QSDT8PCRC Cards Options in the control area To play selected recorded files. The system offers playbackOther Functions Recorded File BackupThen click ‘OK’ to play back Click and enter the following menuClick and the following window will appear Delete Recorded FilesFunction is valid only in playback pause mode Images that have been captured Display print setup as shown belowImage Zoom in/out SuperDVR & QSDT8PCRC Cards19 Example zoomed Remote Live Surveillance Remote Surveillance Server ConfigurationHigher quality setting Setting up Router for Internet AccessPort Forward Router link Port ForwardingFinding Router’s Public IP address It will give you instructions for your routerSuperDVR & QSDT8PCRC Cards标题 Page Advanced Options 10 Invalid Signature Accessing IE clientUnknown Publisher or Unsigned Program Error 11 Webcam install interface Feature Explanations Icon Function of the main interface buttons Explaination of the button functions Play/ Pause Stop Remote playback15 Remote backup Channel configuration window will appear 19 Basic Configuration Click and enter into the main setup interfaceCaption Basic ConfigurationCamera setup Alarm setup configuration is show belowAudio input2 matches channel2 Schedule configurationClick icon to enter into alarm configuration as shown below Alarm configurationRecord setup Enable buzzer on board for alarmRecord configuration Storage disk Motion configurationClick icon to access to Email configuration interface Email ConfigurationMail setup Mail server setupSend time, such as Seconds, 10 seconds and so on 8 P.T.Z ConfigurationPort Users can set port number Baud rate Introduction to Mobile Surveillance Mobile SurveillancePage PCam will be opened after installed By Smart Phone with Symbian Operating System Page Internet It will show the camera after accessing successfully Accessing From iPhones Page Page Pic1Pic2Pic3Pic4 Iphone helpUnderneath. Other functions are PTZ Control buttonsImage View SuperDVR & QSDT8PCRC Cards Appendix 2.2.1 Meanings of the indicator lights Appendix 2.1.1 Cannot Install the SuperDVR DriverPossible causes Card is not compatible with the PC systemAppendix 2.2.8 Why can’t I select more channels to backup? Appendix 2.2.4 How to set auto reboot functionAppendix 2.3.4 Why can’t I see the images? SuperDVR & H.264 Series Cards Appendix 2.4 Other Questions Appendix 2.4.2 Why I can’t find the recorded files?Appendix 2.4.8 Precautions on changing system time Appendix 2.4.5 Why can’t I play back?Once Booted up, On Desktop there will be a ‘SuperDVR’ icon Enter the installation directory of SuperDVRChange can be made directly Once your program is opened, now connect the CamerasSuperDVR & H.264 Series Cards For more details information, please read Chapters Open up Webcam, click ‘Key’ symbol iconClick on ‘Config’ Appendix 4.1 SuperDVR Function Tree Function Tree SuperDVR Series Cards 103 Function Tree

Related manuals

Manual 56 pages 21.3 Kb

Manual 104 pages 32.84 Kb