Technicolor - Thomson 51PW9303 manual Important Safety Instructions

Page 3

IMPORTANT SAFETY INSTRUCTIONS

Read before operating equipment

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with a dry cloth.

7.Do not block any of the ventilation openings. Install in accordance with the manufacturers instructions.

8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9.Do not defeat the safety purpose of the polarized or ground- ing-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and third grounding prong. The wide blade or third prong are provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11.Only use attachments/accessories specified by the manu- facturer.

12.Use only with a cart, stand, tripod, bracket, or table

specified by the manufacturer, or sold with the app-

aratus. When a cart is used, use caution when moving the cart/apparatus combination to avoid

injury from tip-over.

13.Unplug this apparatus during lightning storms or when unused for long periods of time.

14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15.This product may contain lead and mercury. Disposal of these materials may be regulated due to environmental con- siderations. For disposal or recycling information, please contact your local authorities or the Electronic Industries

Alliance: www.eiae.org

16.Damage Requiring Service - The appliance should be serviced by qualified service personnel when:

A.The power supply cord or the plug has been damaged; or

B.Objects have fallen, or liquid has been spilled into the appliance; or

C.The appliance has been exposed to rain; or

D.The appliance does not appear to operate normally or exhibits a marked change in performance; or

E.The appliance has been dropped, or the enclosure damaged.

17.Tilt/Stability - All televisions must comply with recommend- ed international global safety standards for tilt and stability properties of its cabinet design.

• Do not compromise these design standards by applying excessive pull force to the front, or top, of the cabinet which could ultimately overturn the product.

• Also, do not endanger yourself, or children, by placing electronic equipment/toys on the top of the cabinet. Such items could unsuspectingly fall from the top of the set and cause product damage and/or personal injury.

18.Wall or Ceiling Mounting - The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer.

19.Power Lines - An outdoor antenna should be located away from power lines.

20.Outdoor Antenna Grounding - If an outside antenna is connected to the receiver, be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges.

Section 810 of the National Electric Code, ANSI/NFPA No. 70-1984, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding connectors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure below.

21.Object and Liquid Entry - Care should be taken so that objects do not fall and liquids are not spilled into the enclo- sure through openings.

Note to the CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

Example of Antenna Grounding

as per NEC - National Electric Code

GROUND CLAMP

ELECTRIC SERVICE EQUIPMENT

ANTENNA LEAD IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

3

Rev. 8/13/01

Image 3
Contents Hdtv Monitor Warranty Verification Important Safety Instructions Contents End-of-life Disposal FeaturesVideo Jacks Cable used S-Video JACKS, CABLES, and ConnectorsRear of TV Panel Overviews Standard Inputs and OutputsWhat You Can Connect to High-definition Input Jacks Panel Overviews HIGH-DEFINITION InputsHelpful Hint Connecting a VCRConnecting a VCR and Cable BOX See the section below on using the Audio OUT control Connecting and Using AN Audio HI-FI System with Your TVRear of DVD Player Connecting a Standard DVD PlayerConnecting a DVD Player with PROGRESSIVE-SCAN Capability Rear of Device with Video Output Connecting AN S-VIDEO DeviceConnecting AN HD Receiver to the HD INPUT-AV 4 Jacks Connect S-VIDEO and audio cables. Note This example usesConnect coaxial cables Connecting a Camcorder TV’s side panel has a headphone jack for personal listening Connecting and Using Headphones with Your TVVCR Programming the TV Remote to Work Accessory DevicesPlease read through all the steps before beginning Using the CODE-ENTRY Method to Program Your TV RemoteUsing the Search Method to Program Your TV Remote DIRECT-ENTRY Codes for A/V Accessory DevicesLASER-DISC Player DIRECT-ENTRY Codes for A/V Accessory DevicesCH & TV/VCR Using the TV Remote with Accessory DevicesUsing the AV and Source Select Buttons AutoSound Options Using AutosoundUsing Autopicture List Using AutosurfCVI Using Program List and Alternate ChannelSleep Timer Control UsingPicture-adjustment Options Adjusting the Picture ControlsPress the STATUS/EXIT button to turn the menu off Setting the EYE Fidelity ControlSetting the Dynamic Contrast Control Adjusting the TREBLE, BASS, and Balance Controls Using the AVL Audio Volume Leveler Control Selecting the SURROUND-SOUND Modes Selecting a Surround-sound Option Using Remote ControlSelecting the STEREO/MONO Sound Mode Selecting SAP Using Remote Control Selecting the SAP Second Audio Program FeatureUsing the Bass Boost Control Quick Use and Setup Guide Setting the ClockDisplaying the Time Press the Cursor Ring Right to enter the Features submenu Setting the TIMER’S Start Time and Stop TimeSelecting the TIMER’S Channel Setting the TIMER’S Activate Control Understanding Autolock Timer Setting UP the Autolock Access CodeAccess Code Using Autolock to Block ChannelsUsing Autolock to Block by Movie Rating Using Autolock to Block by TV Rating Turning the Autolock Blocking Control on or OFF Onscreen menu Using Autolock to Block Unrated BroadcastsTon on the remote control to show Press the MENU/SELECT butUsing Autolock to Block Broadcasts That have no Rating RIGHT. Then press the CURSOR Ring Down once Press the STATUS/EXIT button on Reviewing Your Current Autolock SettingsMute Using the Closed Captioning ControlSelecting a Picture Format Using the Remote Control Using the PICTURE-FORMAT ControlSelecting a picture Format Using the TV Buttons Picture-quality settings Using Active ControlHD INPUT-AV Model SpecificationsOr AV5 Setting Color Space for the HD InputsVideo-game images and scoreboards Care and CleaningTV has no power TroubleshootingYou are not able to get sound Glossary of Television Terms Index Canada Factory Service LocationsAtlanta Cleveland Chicago Page Projection Television Limited Warranty