Technicolor - Thomson 51PW9303 manual Setting the TIMER’S Start Time and Stop Time

Page 41

Using the Onscreen Submenus: Features

SETTING THE TIMERS START TIME AND STOP TIME

You can set the Timer to switch to a selected channel at a specific time while you are watching another channel, or when the TV is in standby mode. (Standby mode is when the TV is

plugged into the wall outlet but turned off.) If you want, you can also set the TV to turn off at some time after the TV switches channels. Follow the steps below to set the Timer’s START TIME and STOP TIME.

1 Press the MENU/SELECT button on the remote control to show the onscreen menu.

2 Press the CURSOR RING DOWN

twice to highlight FEATURES.

3 Press the CURSOR RING RIGHT to enter the FEATURES submenu.

PICTURE

TIMER

 

FEATURES

 

 

 

 

SOUND

AutoLock

 

TIMER

TIME

FEATURES

CLOSED CAP

 

 

AutoLock

START TIME

INSTALL

FORMAT

 

 

CLOSED CAP

STOP TIME

 

 

 

 

 

 

FORMAT

CHANNEL

 

 

 

 

ACTIVATE

6

 

 

FEATURES

 

 

 

TIMER

 

 

 

 

TIME

8:06 PM

 

 

 

START TIME

 

 

 

 

STOP TIME

 

1

 

7

CHANNEL

 

 

ACTIVATE

 

 

 

 

 

4 Press the CURSOR RING RIGHT again. Then press the CURSOR RING DOWN once to highlight the START TIME control.

5 Press the CURSOR RING RIGHT to highlight the time indicator area.

6 Press the NUMBER buttons to enter the correct time. If you make a mis- take entering the time, use the CUR- SOR RING LEFT or RIGHT to move among the time input slots to make corrections.

NOTE: You can also use the CUR- SOR RING UP or DOWN to cycle through digits to input the time.

7 Press the CURSOR RING UP or DOWN to select AM or PM.

8 Press the CURSOR RING LEFT repeatedly until START TIME is high- lighted. Then press the CURSOR RING DOWN to highlight STOP TIME. If you want the TV to switch off at some time after the changing of channels, follow steps 5–7 above to set the STOP TIME.

9 Press the STATUS/EXIT button to exit the menu.

See pages 42 and 43 for instructions on selecting the Timer’s channel and activating the timer.

8 3,4, 9 2 5

FEATURES

 

TIMER

 

 

TIME

 

 

START TIME

_ _:_ _

 

STOP TIME

 

 

CHANNEL

 

 

ACTIVATE

 

FEATURES

 

TIMER

 

TIME

 

START TIME

8:00 AM

STOP TIME

 

CHANNEL

ACTIVATE

FEATURES

TIMER

TIME

START TIME

STOP TIME

_ _:_ _

CHANNEL

 

ACTIVATE

 

FEATURES

 

TIMER

 

TIME

 

START TIME

 

STOP TIME

9:30 AM

CHANNEL

 

ACTIVATE

 

41

Image 41
Contents Hdtv Monitor Warranty Verification Important Safety Instructions Contents End-of-life Disposal FeaturesVideo Jacks Cable used S-Video JACKS, CABLES, and ConnectorsRear of TV Panel Overviews Standard Inputs and OutputsWhat You Can Connect to High-definition Input Jacks Panel Overviews HIGH-DEFINITION InputsHelpful Hint Connecting a VCRConnecting a VCR and Cable BOX See the section below on using the Audio OUT control Connecting and Using AN Audio HI-FI System with Your TVRear of DVD Player Connecting a Standard DVD PlayerConnecting a DVD Player with PROGRESSIVE-SCAN Capability Rear of Device with Video Output Connecting AN S-VIDEO DeviceConnect coaxial cables Connecting AN HD Receiver to the HD INPUT-AV 4 JacksConnect S-VIDEO and audio cables. Note This example uses Connecting a Camcorder TV’s side panel has a headphone jack for personal listening Connecting and Using Headphones with Your TVVCR Programming the TV Remote to Work Accessory DevicesPlease read through all the steps before beginning Using the CODE-ENTRY Method to Program Your TV RemoteUsing the Search Method to Program Your TV Remote DIRECT-ENTRY Codes for A/V Accessory DevicesLASER-DISC Player DIRECT-ENTRY Codes for A/V Accessory DevicesCH & TV/VCR Using the TV Remote with Accessory DevicesUsing the AV and Source Select Buttons AutoSound Options Using AutosoundUsing Autopicture List Using AutosurfCVI Using Program List and Alternate ChannelSleep Timer Control UsingPicture-adjustment Options Adjusting the Picture ControlsPress the STATUS/EXIT button to turn the menu off Setting the EYE Fidelity ControlSetting the Dynamic Contrast Control Adjusting the TREBLE, BASS, and Balance Controls Using the AVL Audio Volume Leveler Control Selecting the SURROUND-SOUND Modes Selecting a Surround-sound Option Using Remote ControlSelecting the STEREO/MONO Sound Mode Selecting SAP Using Remote Control Selecting the SAP Second Audio Program FeatureUsing the Bass Boost Control Quick Use and Setup Guide Setting the ClockDisplaying the Time Press the Cursor Ring Right to enter the Features submenu Setting the TIMER’S Start Time and Stop TimeSelecting the TIMER’S Channel Setting the TIMER’S Activate Control Understanding Autolock Timer Setting UP the Autolock Access CodeAccess Code Using Autolock to Block ChannelsUsing Autolock to Block by Movie Rating Using Autolock to Block by TV Rating Turning the Autolock Blocking Control on or OFF Ton on the remote control to show Using Autolock to Block Unrated BroadcastsPress the MENU/SELECT but Onscreen menuSOR Ring Down once Using Autolock to Block Broadcasts That have no RatingRIGHT. Then press the CUR Press the STATUS/EXIT button on Reviewing Your Current Autolock SettingsMute Using the Closed Captioning ControlSelecting a Picture Format Using the Remote Control Using the PICTURE-FORMAT ControlSelecting a picture Format Using the TV Buttons Picture-quality settings Using Active ControlHD INPUT-AV Model SpecificationsOr AV5 Setting Color Space for the HD InputsVideo-game images and scoreboards Care and CleaningTV has no power TroubleshootingYou are not able to get sound Glossary of Television Terms Index Canada Factory Service LocationsAtlanta Cleveland Chicago Page Projection Television Limited Warranty