Mount Sub-Frame & Backhoe to Tractor

SUB-FRAME & BACKHOE INSTALLATION TO TRACTOR

This mounting kit is designed to provide secure mounting and adequate operator clear- ance when properly installed. Check clearance dimensions shown in figure 1 to be sure you have installed mounting kit correctly. Follow all mount- ing instructions in this manual. Do not operate backhoe unless there is adequate clearance. Fail- ure to check and comply with these instructions may result in serious injury or death.

The only time the backhoe may be operated from a position other than the operator seat is during backhoe attachment and removal. Opera- tor must

•Read Mounting Kit Manual instructions on attaching and removing backhoe and use extreme care.

•Always stand between rear tire and back- hoe stabilizer arms or along side of tractor to avoid being trapped should the boom swing control be accidentally activated.

Remove seat and upper support assembly before installing or removing backhoe from trac- tor. Failure to comply may result in equipment failure and/or personal injury.

Hydraulic System Check List

Complete check list prior to backhoe operation.

____ Check that backhoe hydraulic pump is

secured to the tractor PTO, if equipped.

____ Check all hydraulic fittings and lines to be

sure they are tight and free of kinks or twists.

____ Check the tractor hydraulic reservoir to

make sure backhoe PTO driven hydraulic sys- tem is full (approximately 5-7 US gallons). Ser- vice if necessary.

NOTE: See the BH6500/7500 backhoe operator man- ual for hydraulic oil recommendations. Do not mix hydraulic fluid types.

1.Remove the backhoe seat assembly.

2.Place sub-frame flat on a hard level surface.

3.Back tractor over the sub-frame and center between the tractor rear tires. Position tractor so that the hydraulic system can be connected. Shut off tractor, set brake, remove key.

4.Install the pump bracket over the tractor drawbar to prevent pump rotation. Engage the pump PTO coupler pin firmly in the tractor PTO spline groove.

5.With the tractor PTO and transmission in neutral, start the engine and run at low idle.

6.Smoothly engage the PTO pump to provide back- hoe hydraulics.

NOTE: Very little engine power is required to operate the hydraulic system in this mode. Should the engine pull down excessively, check the plumbing hook-up for reversed lines or a control lever stuck in an operat- ing position.

NOTE: You will use the backhoe hydraulics to maneu- ver the sub-frame into position. Use care in this pro- cedure to avoid being trapped between tractor and backhoe or between backhoe parts.

7.Raise rear of sub-frame up by lowering stabilizers and boom section until crosstube on sub-frame is level with rear mount channel. Keep front of sub- frame low enough to clear tractor.

8.Drive tractor back until sub-frame crosstube slides into rear mount channel. Shut off tractor, set brake, remove key.

9.Fasten sub-frame in place by placing clevis pins into channel hole secure with safety pins.

10.With the tractor engine off, relieve pressure in the backhoe boom and stabilizers to raise sub-frame into front hanger.

11.Install bent pin and klik pin in front hanger mount.

12.Reinstall seat.

13.Start tractor and put backhoe into transport posi- tion (see backhoe operator’s manual).

NOTE: Install swing lock before transporting.

12 Installation	MAN0094 (11/15/2002)

1016, 2WD, 1009, LA852-1, LB702 specifications

The Woods Equipment MX5000 is a robust and versatile piece of machinery designed for various agricultural and landscaping applications. Known for its durability and efficiency, this model stands out in the market for its innovative features and technologies that cater to both professional and amateur users. The MX5000 is engineered for performance, with a powerful hydraulic system that ensures smooth operation when handling various attachments.

One of the key characteristics of the MX5000 is its impressive lifting capacity. The robust design allows it to handle heavy loads with ease, making it an ideal choice for tasks such as lifting, moving, and tilling. The integrated hydraulic system is user-friendly, offering precise control over attachment operations. Operators can switch between different functions with minimal downtime, enhancing productivity in both agricultural and landscaping tasks.

The MX5000 is also equipped with advanced technologies that improve its operational efficiency. For instance, it features a quick-attach system that allows users to switch between different implements swiftly, reducing the time spent on equipment changes. This flexibility is particularly beneficial for users who need to tackle a variety of tasks in a single workday.

The build quality of the MX5000 is noteworthy. Constructed with high-strength materials, it is designed to withstand the rigors of daily use in demanding environments. The frame is engineered for stability, ensuring that the machine maintains its balance even when fully loaded. This sturdy construction contributes to the longevity of the equipment, making it a sound investment for users who rely on durability.

Additionally, the compact size of the MX5000 allows for enhanced maneuverability in tight spaces. Whether operating in a crowded field or navigating around obstacles, the agility of this model makes it a user-friendly choice. The compact design does not compromise its performance, as it still boasts powerful capabilities to handle various implements.

In summary, the Woods Equipment MX5000 is a standout model characterized by its exceptional lifting capacity, user-friendly hydraulic system, advanced quick-attach technology, and robust construction. This equipment is designed to meet the demands of a wide range of applications, from agriculture to landscaping, making it a valuable asset for any operator. The integration of solid engineering with high-quality materials ensures that the MX5000 provides reliable and efficient performance for years to come.