Emerson EWC1902, EWC1302 owner manual S2 8 9 8 a

Page 3

FIGURE A

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

 

 

 

 

 

 

ANTENNA

 

 

 

 

 

 

L EAD I N

 

 

 

 

 

 

W I R E

 

GROUND

 

C L A M P

 

 

 

 

 

 

ANTENNA

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DI SCHARG E UN I T

 

 

 

 

 

 

(NEC SECTION 8 10 -2 0)

EL ECTRI C

 

 

 

 

 

 

SE RV I CE

 

 

 

 

 

 

EQ U I PMEN T

 

 

 

 

 

 

 

 

 

 

 

 

G RO UNDI NG CO NDUCTORS

 

 

 

 

 

 

(NEC SECTION 8 10 -2 1)

 

 

 

 

 

G RO UND CL AMPS

NEC - NATI O NAL EL ECTRI CAL CO DE

 

 

POWER SERVI C E G RO UNDI NG

 

 

 

EL EC TR O DE SYSTEM

S2 8 9 8 A

 

 

(NEC ART 2 50 , PART H)

13.Outdoor Antenna grounding-If an outside antenna or cable system is connected to the TV/VCR, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA No. 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. (Fig. A)

14.Lightning-For added protection for this TV/VCR receiver during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the TV/VCR due to lightning and power-line surges.

15.Power Lines-An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

16.Overloading-Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

17.Object and Liquid Entry-Never push objects of any kind into this TV/VCR through openings as they may touch dan- gerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the TV/VCR.

18.Servicing-Do not attempt to service this TV/VCR yourself as opening or removing covers may expose you to danger- ous voltage or other hazards. Refer all servicing to quali- fied service personnel.

19.Damage Requiring Service-Unplug this TV/VCR from the wall outlet and refer servicing to qualified service per- sonnel under the following conditions:

a.When the power-supply cord or plug is damaged or frayed.

b.If liquid has been spilled, or objects have fallen into the TV/VCR.

c.If the TV/VCR has been exposed to rain or water.

d.If the TV/VCR does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as improper adjust- ment of other controls may result in damage and will often require extensive work by a qualified technician to restore the TV/VCR to its normal operation.

e.If the TV/VCR has been dropped or damaged in any way.

f.When the TV/VCR exhibits a distinct change in perfor- mance-this indicates a need for service.

20.Replacement Parts-When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same character- istics as the original part. Unauthorized substitutions may result in fire, electric shock, injury to persons or other haz- ards.

21.Safety Check-Upon completion of any service or repairs to this TV/VCR, ask the service technician to perform routine safety checks to determine that the TV/VCR is in proper operating condition.

22.Heat-This TV/VCR product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

- 3 -

EN

9I03

Image 3
Contents OWNER’S Manual Important Safeguards S2 8 9 8 a Important Copyright Information PrecautionsLocation Avoid the Hazards Electrical Shock and FireIndice Table of ContentsSupplied Accessories Features9101112 Operating Controls and FunctionsRear View ANTENNA/CABLE Connections Preparation for USEChannel SET UP for First Time SET UP for USEExternal Input Mode Installing the BatteriesTo Select a Desired Channel Clock SET UP Auto / ManualAuto Clock Setting Manual Clock SettingSET Channel SET UP AgainTo Change Clock Setting Deleting or Adding ChannelTo Cancel the DAYLIGHT-SAVING Time DAYLIGHT-SAVING TimeSelecting the Language Picture Control Game ModeTV Operation Watching a TV ProgramTV Rating SET UP Chip SET UPTo Cancel the Closed Caption System When the Closed Caption Mode is onMpaa Rating SET UP When you select TV-Y7Selection Rating Category Explanations Playback Auto Repeat PlaybackNormal Playback Zero Return SearchStill Picture Picture SearchPicture Controls RecordingSkipping Unwanted Scenes During Recording Normal RecordingTimer Recording Pushes Display Recording lengthChannel CH61 Tape Speed SP Timer Program Extension To Correct a ProgramTo set another program, repeat steps 2 to Hints for Automatic Timer Recording Wake UP TimerAuto Return Copying a Video Tape Sleep TimerTo Cancel the Wake UP Timer To Cancel the Sleep TimerReal Time Tape Counter Special FeaturesMaintenance On Screen DisplayTV/VCR Troubleshooting GuideProblem Corrective Action Closed Caption Problem Possible RemedyOther Specifications SpecificationsGeneral Specifications Electrical SpecificationsControles DE Operación Y SUS Funciones Botón B Conexiones DE ANTENA/CABLE Preparación DE Canales POR Primera VEZ Funai Corporation TelPlease do not Ship Your Unit to the Teterboro Address