Magnavox CCB255AT Turning On the TV/VCR, Press the Combi button, then press the Power button

Page 8

8 Turning On the TV/VCR

Before you turn on the TV/VCR, make sure batteries are in the remote control and the TV/VCR is hooked up correctly.

The instructions on this page work only when you turn on the TV/VCR for the first time.

1

Press the COMBI button, then press the POWER button.

The TV/VCR will come on and the screen shown below will appear.

SELECT LANGUAGE

> ENGLISH

ON

1

2

3

POWER
SLEEP/WAKE UP	SPEED
REC/OTR

	PLAY
REW
	STOP
MENU	STATUS/EXIT

EJECT
MEMORY
PAUSE/STILL	4
F.FWD	4
CLEAR

ESPAÑOL

SELECT KL OR

PRESS MENU TO CONTINUE

2

Press the PLAY/K button or the STOP/L button to select

English or Spanish on-screen displays and menus.

3

Press the MENU button. The screen shown below will appear.

CONNECT ANTENNA OR CABLE

TO TVCR

THEN PRESS B

TO END PRESS EXIT

4

Press the F.FWD/B button to begin automatic channel setup. The TV/VCR will memorize all available channels. When channels are set, CHANNELS ARE SET will appear on the screen briefly. Then the TV/VCR will go to the lowest channel pro- grammed.

(If you try to set up channels when there is no antenna or cable connected to the TV/VCR, programming will appear to take place, but eventually a NO TV SIGNALS ... message will appear on the screen. Connect an antenna or cable to the ANT(enna) jack on the TV/VCR, then press the F.FWD/B button again. You may need to follow the steps on page 10 instead.)

5

Use the CH(annel) m/n button or the Number buttons on the remote control to select a TV/VCR channel. Use the VOL(ume) m/n button to adjust the sound.

	1	2	3
	4	5	6	CH.	5
	4	5	6
	7	8	9
1	FM	0	SURF	VOL.
	CABLE/DBS	COMBI
			VCR PLUS+
	VAR.SLOW		/ENTER	MUTE
	TRACKING		F.ADV	SLOW
	SMART		SKIP INDEX
	PICTURE	SOUND	SEARCH SEARCH

Helpful Hints

•If you do not see any on-screen dis- plays when you turn on the TV/VCR, check your hookups, then try again. If you still do not see any on-screen displays, follow the steps on pages nine-10 to select a language and set up channels.

•To skip step 2, press the MENU button. All on-screen displays will be in English. To skip step 4, press the STATUS/EXIT button. Channels will not be set up, and CHANNELS NOT SET will appear on the screen briefly.

•You cannot set up channels if you are using a Cable Box.

•Line Input mode will always be stored in the TV/VCR’s memory as channel 00. When you select chan- nel 00, A/V IN will appear on the screen briefly. Press the CH(annel) m/n button or the Number but- tons to select another channel.

Image 8

Contents CCB255AT Dear Philips product owner For Customer UseThis bolt of lightning indi- cates uninsulated material Model No Serial NoFeatures Safety PrecautionsIntroduction Declaration of ConformityTable of Contents Putting Batteries in the Remote Control Using the Remote ControlTV/VCR Maintenance Erasure PreventionHook up your TV/VCR using one of the connections shown Hooking Up the TV/VCRRF coaxial cable Not supplied Rod AntennaHooking Up the TV/VCR cont’d Jacks on VCRBent pin Crooked Pin Straight PinPress the Menu button. The screen shown below will appear Press the Combi button, then press the Power buttonTurning On the TV/VCR Language Selection Press the Combi button, then press the Menu buttonAutomatic Channel Setup Wait for the TV/VCR to set up channelsAdding/Deleting Channels Press the PLAY/o button or the STOP/p button to selectRepeat steps 3-4 to add or delete other channels Programming of the last channel you selected will appearCable Box users must set the clock manually Setting the ClockManual Clock Setting Setting the Clock cont’d Setting the Clock cont’d Automatic PBS Channel SelectionNOW Searching flashes on the TV/VCR screen Wait for the TV/VCR to findTime Manual PBS Channel Selection Use the Number buttons to select your PBS station Wait for the TV/VCR to find the timeDaylight-Savings Time Time Daylight Savings TimePress the PLAY/ button or the STOP/ button to select PRIM. SETUP. Then, press the F.FWD/B buttonTime Zone Setting the Remote to Operate a Cable Box/DBS Cable BOX CodesSetting the Remote to Operate a Cable Box/DBS cont’d Front Panel AC Power Cord Rear PanelANTenna Jack Connect your antenna or cable hereRemote Control Buttons VOLume m/ n Button PAUSE/STILL ButtonMemory Button REWind/ ButtonAdjusting the Picture Controls Adjust the picture control. Refer to the chart onWhen you finish, press the STATUS/EXIT button Press the REWind/ button or the F.FWD/B button toDecrease Increase Decreased brightnessOn-Screen Status Displays If you select Status ON, then select Counter only OFFIf you select Status ON, then select Counter only on If you select Status OFFPlaying Insert a tape in the TV/VCRPress the RECord/OTR button once to start recording Power button to turn on the TV/VCR, if necessaryRecording One-Touch Recording OTRRerecording Tape Duplication Different brands of equipment may operate differentlyDefeat Recording Follow the steps below to prevent accidental recordingDaily Timer RecordingLowed by the SET Clock menu Timer Recording cont’d Timer Recording cont’d FM 0 Surf VOLChecking or Clearing Timer Recordings Station Setting Up the VCR Plus+ Programming SystemTV Channels Setting Up the VCR Plus+ Programming System cont’d Timer Recording With the VCR Plus+ Programming System You have completed the steps on pagesTimer Recording With the VCR Plus+ Programming System cont’d Real-Time Counter Memory Appear on the screenON-SCREEN Mode Defeat Recording OFF Repeat PlayB Repeat Play Insert a tape in the TV/VCRRepeat Play cont’d Flashing a will become a flashing BPlayback Options Forward and Reverse Searching SP/LP/SLPSuper High Speed Searching LP/SLP Viewing a Still PictureBlue Background SmartLock To block ratings, follow the steps belowExample Specific Sub-ratings SmartLock cont’dRatings are defined on To change the access code, follow these steps After you enter the code, the Smartlock menu will appearTo check the SmartLock settings, follow these steps TV-Y7Press the Combi button, then press the SLEEP/WAKE UP button Sleep TimerTimer during a recording Wake Up Timer Closed Caption ExampleMenu ScreenHalf-screen text Closed Caption cont’dStandard Closed Captions Volume Bar/Smart Sound Volume BarVolume will stay at the same level Smart SoundAutomatic Operation Features SmartPicture/FM Radio SmartPictureFM Radio Press the CHannel m/n button until your desired radioIf another remote control beeps Press the Mute button, then press the PAUSE/STILL buttonReminder Press the Combi button, then press the Menu buttonIndex Search Specifications Glossary Helpful Hints Helpful Hints cont’d Renewed Index Supplied Accessories