Toshiba HD-A2WKU manual Connect the player to your TV, Via Hdmi input

Page 21

Chapter2Connections

Step2 Connect the player to your TV.

Introduction

Via HDMI input

HDMI stands for High Definition Multimedia Interface. HDMI transfers digital audio and uncompressed digital video on a single cable. As a result, audio cables and video cables don’t need to be connected separately to a device.

Connections

HDMI INPUT

Depending on the equipment connected to this player, such as a TV or a projector, no sound may be output by the display.

In this case, set “Digital Out HDMI” ( page 53) to “PCM”.

If sound still is not heard, use analog output.

To HDMI OUTPUT

HDMI cable (not supplied)

Finally connect the supplied

power cord to a wall outlet.

 

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

(Basic)

Playback

(Advanced)

Playback

connection

Internet

This player supports simultaneous output of video on its HDMI and component video ports. However, some discs may restrict output of video on the component video ports when viewing high definition content or up-converted DVD content. The resolution on the HDMI output will be the same as the resolution output on the component video output. Thus, because the HDMI output can change automatically to match the maximum available resolution of your display, if you connect both the HDMI output and component output, the resolution on the component output will change if the HDMI output Auto-adjusts.

After completing the connection, proceed to page 23 to make the setting.

Notes

•Refer to the owner’s manual for the TV to be connected to this player for more information concerning HDMI connections.

•When the HDMI connection is not verified, an error message appears on the front panel display. In this case, disconnect the HDMI cable then connect it again, or turn off the connected HDMI device then turn it on.

•HDMI output is digital only, DVI analog is not supported.

•HDMI is an evolving technology, so it is possible that some devices may not operate properly with this player.

•To get the most possible benefit from Dolby Digital Plus, you should connect your HD DVD player to your AV receiver using either its HDMI audio capable input. If your AV receiver has this type of input(s), make sure one of them is connected to your HD DVD player and that the input is set to use audio from HDMI (and not the SPDIF coaxial or optical input). If your AV receiver does not have an HDMI input, but it can decode DTS, then the next best choice is to use the SPDIF (coaxial or optical) input on your AV receiver. While this connection does not have enough bandwidth to transport the full, high-quality Dolby Digital Plus signal, it will support DTS – the highest bandwidth commonly available encoding method that does work over SPDIF. If your receiver does not support DTS, you may be able to obtain a two channel digital by setting the player to output PCM. If your receiver does not have either HDMI or an optical digital input, use the two channel analog outputs.

•If you use the SPDIF optical output or analog outputs to connect your audio system and have the “Digital Out HDMI” ( page 53) set to “Auto” or “PCM”, the audio output level from these jacks will be reduced when listening to a multi- channel disc. To restore the audio output level, set “Digital Out HDMI” to “Downmixed PCM”.

Others

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents HD DVD player See service procedure This HD DVD player employs a Laser SystemMay result in hazardous radiation exposure Location of the required label 24!.4.3!&%49 .3425#4/.3 Additional Safety Instructions Precautions Moisture condensation occurs during the following cases Do not use the unit when moisture condensation may occurFeatures Certain limitations Customer support AccessoriesTable of Contents 7Firmware update Advanced7Picture Others 7Audio 7Language 7Ethernet 7General Index to parts and controls Front panelSee pages with arrows for details LAN port Rear panelDisplay Disc indicatorAvailable by software update Remote controlFor future functions which may become May be specified depending on the discOperating with the remote control Preparation of the remote controlOpen the cover Insert batteries Close the coverRelease Operating your TV with the remote controlProgramming for TV control Brand code table Icons for function applicability Hint on reading this manual Instructions and actual buttons Icon DiscConnections Check the type of video input on your TV Connecting to a TVHdmi input Component videoVia Hdmi input Connect the player to your TVVia component video input Via S-VIDEO or Video yellow inputConnect either Setting of video output resolution of this player Configure settings for your displayVia Hdmi output Connecting to an audio systemVia optical digital audio output Make the connection as below, and set Digital Out HdmiBasic Playback Page Playback Basic Pre-recorded discs Disc compatibilityRecordable discs you can play on this player Disc SpecificationOn cleaning discs On handling discsOn storing discs Press front panel or remote control Powering on/Loading a discDown Press ON/STANDBYPlaying a disc Stopping playback / Pausing playbackLoad a disc and close the disc tray If playback does not startPress Press To select the title You wantPress / / / to select the item you want Selecting the sound of a disc recorded in DVD VR mode Press while the audio setting is displayed On the TV screenStereo sound contents During playback, pressPress while playing a scene recorded with Multiple angles Press during playbackSelecting subtitles Selecting the camera anglePlaying in fast reverse or fast forward Playing at various speedsLocating by entering a section number Press repeatedly to select the area you want to inputLocating by entering elapsed time You can resume playback from the location lastPlayback Advanced Repeat playback Press To select the repeat modeYou can repeat a desired section Repeat modes are listedPress While a disc with Support for cursor use is playing Extension portsUse the eight direction buttons to Move the cursorYou can confirm operational status and setting details Checking the current status and settingsInternet connection Internet connection feature Outline Before usingConnection requirement Basic Playback Connection Connecting using a router e.g. Adsl2nd Proxy setting 1st Dhcp setting3rd NTP Server setting 4th Network Speed settingUser information setting Select an item from the menu Insert the HD DVD disc and close the trayPage Others Press / to select the setting item, then Customizing the function settingsDuring stop, press Returns to the previous screenProgressive TV Picture Audio BitstreamDownmixed PCM Language Ethernet Set the details GeneralSelect On or Off by pressing / buttons. On Select the desired limitation level by pressing / buttonsClock starts Auto Power OffUpdate Firmware update InitializePersistent Storage Language code list Output sound conversion table GNU General Public License Version 2, June H i b i t aOthers No Warranty GNU Lesser General Public License Version 2.1, February H i b i t BBasic Playback Version ever published by the Free Software Foundation H i b i t D H i b i t CBefore calling service personnel Video output Operating conditions SpecificationLimited One 1 Year Warranty on Parts Limited Ninety 90 Day Warranty on LaborYour Responsibility Rental UnitsHow to Obtain Warranty Services Information on Customer Support
Top Page Image Contents