Toshiba Complete Guide for Your 26HF85 Television
Page 17

To control a DVD player:

Program the remote control to recognize the brand of your DVD player (see “Programming the remote control to operate your other devices” below.) The buttons shown at right will then control the DVD player.

Press “DVD” first.

Power

Input (TV)

Recall

Mute (TV)

Number

buttons

Volume +/- (TV)

DVD

Pic Size (TV)

DVD MENU

▲▼ ▼▼

ENTER DVD controls

DVD Skip/Search

/

TOP Menu

DVD Clear

Safeguards

Important

ToshibaWelcome to

Programming the remote control to operate your other devices

This remote control is pre-programmed to operate Toshiba satellite receivers, VCRs and DVD players. To control cable TV converters/ satellite receivers, VCRs and DVD players other than Toshiba models, you must follow the steps below to program your remote control.

1.Refer to the code tables (on pages 18 and 19) to find the corresponding code for your brand.

If more than one code is listed, try each one separately until you find the one that works.

2.If you are programming the remote control to operate your:

•Cable TV converter/satellite receiver: Press “CBL/SAT.”

•VCR: Press “VCR.”

•DVD player: Press “DVD.”

3.While holding down RECALL, press the Channel Number buttons to enter the three-digit code for your cable TV converter/satellite receiver, VCR or DVD player brand.

4.Point the remote control at the cable TV converter/satellite receiver, VCR or DVD player, and press POWER to test the code.

•If the cable TV converter/satellite receiver, VCR or DVD player responds, you entered the correct code.

•If the cable TV converter/satellite receiver, VCR or DVD player does not respond, repeat steps 1–4 using another code.

5.Press “TV” to control the TV.

For future reference, write down the codes you used:

Cable TV converter/satellite receiver code _____________________

VCR code ______________________________________________

DVD player code _________________________________________

17

Recall

Channel

Numbers

TV

VCR

DVD

CBL/SAT

Notes:

•When shipped from the factory, the remote control is set to operate your TV.

•If you do not enter the code within 10 seconds from step 1 or if you enter a code not listed below, this operation is canceled.

•Each time you replace the batteries, you must reprogram the remote control.

•Some newer VCRs are capable of working on either of two remote codes. These VCRs have a switch labeled “VCR1/VCR2.”

If your VCR has this kind of switch and does not respond to any of the codes for your VCR, set the switch to the other position (VCR1 or VCR2) and reprogram the remote control.

yourConnecting TV

Remote ControlUsing the

your TVSetting up

FeaturesUsing the TV’s

Appendix

J3S40121A(E)_P16-23

17

18/01/2005, 9:49 AM

Page 16 Page 18
Image 17
Page 16 Page 18
Contents 26HF85 30HF85 Child Safety Important Safety Instructions Care Connecting your TV Important Safety Information Welcome to ToshibaUsing the remote control Setting up your TVSelecting a location for the TV Welcome to ToshibaExploring your new TV Stereo VCR Connecting your TVConnecting a VCR Option 1 For Subscribers to Basic Cable TV Service Connecting a cable converter box or AntennaConnecting a DVD player/satellite receiver and a VCR DVD player with Component video DTV Receiver With Component video Connecting two VCRs Connecting a camcorder To connect a DVI device, you will need Connecting an Hdmi or a DVI device to the Hdmi inputTo connect an Hdmi device, you will need Amplifier Connecting an audio systemPreparing the remote control for use Using the remote controlInstalling the remote control batteries Using the remote control to operate your other devicesTo control a DVD player Programming the remote control to operate your other devicesVCR Htib Using Remote Learning about the remote controlChanging the on-screen display language Setting up your TVStarting setup Adding channels to the TV’s memory Image tilt correctionProgramming channels automatically Adding and erasing channels manuallyAdjusting the channel settings Using the TV’s featuresSwitching between two channels Changing channelsSelecting a password Using the Locks menuTo select your password and access the Locks menu To clear your favorite channelsUsing the V-Chip parental control feature To lock channels Locking channelsList of locked channels. Then Press EnterTo set up the video lock Setting the GameTimerTMTo set up the GameTimer Locking the video inputsLabeling channels Using the front panel lock featureTo label the video input sources Selecting the video input sourceLabeling the video input sources Setting the ON/OFF timer Setting the clockNatural picture size Selecting the picture sizeFull picture size for 169 source programs Damage is not Covered by Your WarrantyTheaterWide 2 picture size for letter box programs Scrolling the TheaterWide picture TheaterWide 2 and 3 only Scrolladjustmentto +20Selecting the display format for 480p signals only Selecting the cinema modeUsing the Aspect feature Adjusting the picture quality Adjusting the picture Selecting the picture modeTo select the picture mode To adjust the picture qualitySelecting the Scan Velocity Modulation SVM Selecting the color temperatureUsing the CableClear feature Using the closed caption feature Resetting your picture adjustmentsSetting the sleep timer Adjusting the sound quality Adjusting the sound Muting the soundTo adjust the sound quality Selecting stereo/SAP broadcastsUsing the BBE sound feature Resetting your audio adjustmentsUsing the StableSound feature Displaying on-screen information Turning off the built-in speakersSelecting the Hdmi audio input source Understanding the Power Return feature Auto power offTroubleshooting Symptom SolutionVideo Input SpecificationsVIDEO/AUDIO Input VIDEO/AUDIO OutputLimited United States Warranty National Service Division
Related manuals
Manual 44 pages 13.26 Kb
Top Page Image Contents