Toshiba 26HF85, 30HF85 appendix Connecting a cable converter box or Antenna

Page 8

Connecting your TV

Connecting a cable converter box or Antenna

This television has an extended tuning range and can tune most cable channels without using a cable company supplied converter box. Some cable companies offer “premium pay channels” in which the signal is scrambled. Descrambling these signals for normal viewing requires the use of a descrambler device, which is generally provided by the cable company.

Option 1 : For Subscribers to Basic Cable TV Service

For basic cable service not requiring a Converter/Descrambler box, connect the incoming 75 ohm Coaxial Cable directly to the Antenna Jack on the back of the television.

Option 2 : For Subscribers to Scrambled Cable TV Service

If you subscribe to a cable service that requires the use of a Converter/ Descrambler box, connect the incoming cable to the Converter/ Descrambler box and connect the output of the box to the Antenna Jack on the back of the television. Follow the connections shown below. Set the television to the output of the Converter/Descrambler box (usually channel 3 or 4) and use the Converter/Descrambler box to select channels.

Option 3 : For Subscribers to Unscrambled Basic Cable with Scrambled Premium Channels

If you subscribe to a cable service in which basic cable channels are unscrambled and premium channels require the use of a Converter/ Descrambler box, you may wish to use a two-set signal splitter (some- times called a “two-set coupler”) and an A/B Switch box from the cable installer or an electronics supply store. Follow the connections shown below. With the switch in the “B” position, you can directly tune any nonscrambled channels on your TV. With the switch in the “A” position, tune your TV to the output of the Converter/Descrambler box (usually channel 3 or 4) and use the box to tune scrambled channels.

From Cable

Option 1:

Option 2:

Converter/Descrambler

Converter/Descrambler

 

Option 3:

 

 

Splitter

A / B Switch

A B

Note:

When you use a converter box with your TV, there may be features that you cannot program using the remote control, such as labeling channels, blocking channels, and programming your favorite channels.

TV

8

J3S40121A(E)_P07-15

8

18/01/2005, 9:49 AM

Image 8
Contents 26HF85 30HF85 Child Safety Important Safety Instructions Care Important Safety Information Welcome to Toshiba Connecting your TVUsing the remote control Setting up your TVSelecting a location for the TV Welcome to ToshibaExploring your new TV Stereo VCR Connecting your TVConnecting a VCR Connecting a cable converter box or Antenna Option 1 For Subscribers to Basic Cable TV ServiceConnecting a DVD player/satellite receiver and a VCR DVD player with Component video DTV Receiver With Component video Connecting two VCRs Connecting a camcorder To connect a DVI device, you will need Connecting an Hdmi or a DVI device to the Hdmi inputTo connect an Hdmi device, you will need Connecting an audio system AmplifierUsing the remote control Preparing the remote control for useInstalling the remote control batteries Using the remote control to operate your other devicesProgramming the remote control to operate your other devices To control a DVD playerVCR Htib Learning about the remote control Using RemoteChanging the on-screen display language Setting up your TVStarting setup Image tilt correction Adding channels to the TV’s memoryProgramming channels automatically Adding and erasing channels manuallyUsing the TV’s features Adjusting the channel settingsSwitching between two channels Changing channelsUsing the Locks menu Selecting a passwordTo select your password and access the Locks menu To clear your favorite channelsUsing the V-Chip parental control feature Locking channels To lock channelsList of locked channels. Then Press EnterSetting the GameTimerTM To set up the video lockTo set up the GameTimer Locking the video inputsUsing the front panel lock feature Labeling channelsTo label the video input sources Selecting the video input sourceLabeling the video input sources Setting the clock Setting the ON/OFF timerSelecting the picture size Natural picture sizeFull picture size for 169 source programs Damage is not Covered by Your WarrantyTheaterWide 2 picture size for letter box programs Scrolladjustmentto +20 Scrolling the TheaterWide picture TheaterWide 2 and 3 onlySelecting the display format for 480p signals only Selecting the cinema modeUsing the Aspect feature Adjusting the picture Selecting the picture mode Adjusting the picture qualityTo select the picture mode To adjust the picture qualitySelecting the Scan Velocity Modulation SVM Selecting the color temperatureUsing the CableClear feature Using the closed caption feature Resetting your picture adjustmentsSetting the sleep timer Adjusting the sound Muting the sound Adjusting the sound qualityTo adjust the sound quality Selecting stereo/SAP broadcastsUsing the BBE sound feature Resetting your audio adjustmentsUsing the StableSound feature Displaying on-screen information Turning off the built-in speakersSelecting the Hdmi audio input source Auto power off Understanding the Power Return featureTroubleshooting Symptom SolutionSpecifications Video InputVIDEO/AUDIO Input VIDEO/AUDIO OutputLimited United States Warranty National Service Division
Related manuals
Manual 44 pages 13.26 Kb