Toshiba AM40 appendix Connecting a PC Personal Computer, Power connection, To use AC power

Page 16

Connecting your TV

Connecting a PC (Personal Computer)

Before you connect this TV to your PC, change the adjustment of your PC’s Resolution and Refresh rate. See “Monitor Display modes” at right.

Connect one end of a (male to male) VGA cable to the video card of the computer and the other end to the VGA connector PC at the side of the TV. Fix the connectors firmly with the screws on the plug. In case of a Multimedia computer, connect the audio cables to the audio outputs of your Multimedia computer and to the AUDIO L and R connectors of the PC IN jacks of the TV.

Set the video input source to PC mode (see “Selecting the video input source” on page 29 and “Picture/Audio adjustments in the PC mode” on page 39). The TV can be used as a computer monitor.

TV side panel

To PC

You will need:

• one VGA cable

Monitor Display modes

 

MODE

Resolution

Refresh rate

VGA

640x480

60Hz

SVGA

800x600

56.3Hz

SVGA

800x600

60.3Hz

XGA

1024x768

60Hz

WXGA

1280x720

60Hz

WXGA

1280x768

60Hz

Notes:

•The current signal source does not display when you return to TV mode.

•The on-screen displays will have a different appearance in PC mode than in TV mode.

•When you select WXGA mode, set the WXGA INPUT to ON in the PC PICTURE menu (see page 39.)

Power source

Power connection

To use AC power

1.Connect the AC cord to the AC adapter.

2.Connect the AC adapter plug into the TV’s DC input jack.

3.Connect the AC cord into a wall outlet.

To DC

 

AC 120V,

input jack

2

60Hz

 

3

 

 

 

1

 

 

AC adapter

AC cord

 

(supplied)

(supplied)

16

Notes:

•Make sure to insert the plug of each cord securely.

•During use the AC adapter becomes warm. This is not a malfunction.

WARNING:

•Do not connect this unit to the power source using any device other than the supplied AC adapter or power cord. This could cause fire, electric shock, or damage.

•Do not use with a voltage other than the power voltage displayed. This could cause fire, electric shock, or damage.

•Never lift the AC adapter by holding the AC cord. The AC adapter may fall, causing personal injury or equipment damage.

CAUTION:

•Do not use the AC adapter if it is covered by a cloth etc., or pressed into a narrow area. This results in poor dissipation of heat and may cause fire, electric shock, or damage.

•When this unit is not used for a long time, (e.g., away on a trip) in the interest of safety, be sure to unplug it from the wall outlet.

•Do not plug/unplug the plug when your hands are wet. This may cause electric shock.

•If you need to replace the supplied AC adapter or AC cord, the specified AC adapter and AC cord must be used. Contact the dealer that you purchased the unit from.

J3U70221A(E)P11-16

16

05/08/2005, 10:13 AM

Page 15 Page 17
Image 16
Page 15 Page 17
Contents 20HL85 Child Safety Risk of DEATH, Serious Personal INJURY, or Equipment Damage S3126APower Lines HeatConnecting Headphones LCDPrecautions ScrewConnecting your TV Power sourceSetting up your TV Using the TV’s featuresExploring your new TV Selecting a location for the TV Connecting a VCRStereo VCR Option 1 For Subscribers to Basic Cable TV Service Connecting a cable converter box or antennaOption 2 For Subscribers to Scrambled Cable TV Service Connecting a DVD player/satellite receiver and a VCR DVD player with Component video From DTV Antenna Connecting a camcorder To connect an Hdmi device, you will need Connecting an Hdmi or a DVI device to the Hdmi inputTo connect a DVI device, you will need Connecting a PC Personal Computer Power connectionTo use AC power Monitor Display modesInstalling the remote control batteries Preparing the remote control for useUsing the remote control to operate your other devices Programming the remote control to operate your other devices To control a DVD playerVCR DVD Learning about the remote control CBL/SAT DVDStarting setup Changing the on-screen display languageTo select a language PressAdding channels to the TV’s memory Programming channels automaticallyAdding and erasing channels manually Changing channelsSwitching between two channels Adjusting the channel settingsProgramming your favorite channels Using the Locks menu Selecting a passwordTo select your password and access the Locks menu To change your passwordLocking channels Locking the video inputsSetting the GameTimerTM Using the panel lock featureTo create channel labels Labeling channelsTo erase channel labels Setting the clock Selecting the video input sourceLabeling the video input sources To label the video input sourcesTimer Setting the on timerTo cancel the on timer Selecting the picture size Natural picture sizeTheaterWide picture size for 43 format programs Full picture size for 169 source programsSelecting the cinema mode Using the Aspect featureTo set the Cinema Mode to Film To set the Cinema Mode to Video offSetting the sleep timer Using the closed caption featureAdjusting the picture Selecting the picture modeAdjusting the picture quality Mode Picture QualitySelecting the color temperature Using the CableClear featureResetting your picture adjustments Adjusting the sound Adjusting the sound qualityMuting the sound Selecting stereo/SAP broadcastsUsing the StableSound feature Resetting your audio adjustmentsUsing the WOW surround sound feature Understanding the Power Return feature Adjusting the back lighting featureSelecting the Hdmi audio input source Resetting your picture/audio adjustments in the PC mode Picture/Audio adjustments in the PC modePicture menu Symptom Solution TroubleshootingPower Specifications Limited Canada Warranty Memo Service Centers
Top Page Image Contents