Toshiba AM40 appendix Programming the remote control to operate your other devices

Page 18

To control a DVD player:

Program the remote control to recognize the brand of your DVD player (see “Programming the remote control to operate your other devices” below.) The buttons shown at right will then control the DVD player.

Press “DVD” first.

Power

INPUT DISPLAY

Input (TV)

Display

Mute (TV)

Number

buttons

Volume +/- (TV)

DVD

Pic Size (TV)

DVD MENU

▲▼ ▼▼

ENTER DVD controls

DVD Skip/Search

/

TOP Menu

DVD Clear

Setting up your TV

CT-885

Programming the remote control to operate your other devices

This remote control is pre-programmed to operate most Toshiba satellite receivers, VCRs, and DVD players. To control a non-Toshiba device (or a Toshiba device that the remote control is not pre-programmed to operate), you must follow the steps below to program your remote control.

1.Refer to the code tables (on pages 19 and 20) to find the corresponding code for your device.

If more than one code is listed, try each one separately until you find the one that works.

2.If you are programming the remote control to operate your:

•Cable TV converter/satellite receiver: Press “CBL/SAT.”

•VCR: Press “VCR.”

•DVD player: Press “DVD.”

3.While holding down DISPLAY, press the Channel Number buttons to enter the three-digit code for your device within 10 seconds. Note: If you do not enter the code within 10 seconds from step 3,

or if you enter the wrong code, this operation is canceled.

4.Point the remote control at the cable TV converter/satellite receiver, VCR or DVD player, and press POWER to test the code.

•If the device responds, you entered the correct code.

•If the device does not respond, repeat steps 1–4 using another code.

5.Press “TV” to control the TV.

For future reference, write down the codes you used:

Cable TV converter/satellite receiver code _____________________

VCR code ______________________________________________

DVD player code _________________________________________

18

INPUT DISPLAY

Display

Channel

Numbers

TV

VCR

DVD

CBL/SAT

CT-885

Notes:

•When shipped from the factory, the remote control is set to operate your TV.

•Each time you replace the batteries, you must reprogram the remote control.

•Some newer VCRs are capable of working on either of two remote codes. These VCRs have a switch labeled “VCR1/VCR2.”

If your VCR has this kind of switch and does not respond to any of the codes for your VCR, set the switch to the other position (VCR1 or VCR2) and reprogram the remote control.

J3U70221A(E)P17-24

18

05/08/2005, 10:13 AM

Page 17 Page 19
Image 18
Page 17 Page 19
Contents 20HL85 Child Safety Risk of DEATH, Serious Personal INJURY, or Equipment Damage S3126APower Lines HeatConnecting Headphones LCDPrecautions ScrewSetting up your TV Connecting your TVPower source Using the TV’s featuresExploring your new TV Connecting a VCR Selecting a location for the TVStereo VCR Connecting a cable converter box or antenna Option 1 For Subscribers to Basic Cable TV ServiceOption 2 For Subscribers to Scrambled Cable TV Service Connecting a DVD player/satellite receiver and a VCR DVD player with Component video From DTV Antenna Connecting a camcorder Connecting an Hdmi or a DVI device to the Hdmi input To connect an Hdmi device, you will needTo connect a DVI device, you will need To use AC power Connecting a PC Personal ComputerPower connection Monitor Display modesPreparing the remote control for use Installing the remote control batteriesUsing the remote control to operate your other devices Programming the remote control to operate your other devices To control a DVD playerVCR DVD Learning about the remote control CBL/SAT DVDTo select a language Starting setupChanging the on-screen display language PressAdding and erasing channels manually Adding channels to the TV’s memoryProgramming channels automatically Changing channelsAdjusting the channel settings Switching between two channelsProgramming your favorite channels To select your password and access the Locks menu Using the Locks menuSelecting a password To change your passwordLocking channels Locking the video inputsSetting the GameTimerTM Using the panel lock featureLabeling channels To create channel labelsTo erase channel labels Labeling the video input sources Setting the clockSelecting the video input source To label the video input sourcesSetting the on timer TimerTo cancel the on timer TheaterWide picture size for 43 format programs Selecting the picture sizeNatural picture size Full picture size for 169 source programsTo set the Cinema Mode to Film Selecting the cinema modeUsing the Aspect feature To set the Cinema Mode to Video offSetting the sleep timer Using the closed caption featureAdjusting the picture quality Adjusting the pictureSelecting the picture mode Mode Picture QualityUsing the CableClear feature Selecting the color temperatureResetting your picture adjustments Muting the sound Adjusting the soundAdjusting the sound quality Selecting stereo/SAP broadcastsResetting your audio adjustments Using the StableSound featureUsing the WOW surround sound feature Adjusting the back lighting feature Understanding the Power Return featureSelecting the Hdmi audio input source Picture/Audio adjustments in the PC mode Resetting your picture/audio adjustments in the PC modePicture menu Troubleshooting Symptom SolutionPower Specifications Limited Canada Warranty Memo Service Centers
Top Page Image Contents