Toshiba DLPTM, 62HM14 owner manual How to replace the lamp unit, Introduction Connecting your TV

Page 57

How to replace the lamp unit

Required tool: Manual Phillips screwdriver; gloves.

Optional tool: 5/32” or 4mm Allen wrench.

1. Turn off the TV and unplug the power cord.

WARNING: Eye damage may result from

directly viewing the light produced by this lamp. Always turn off the TV and unplug the power cord before opening the lamp unit door.

2. STOP! Allow the lamp to cool for at least one (1) hour before replacing it.

WARNING: RISK OF

ELECTRIC SHOCK!

TO REDUCE THE RISK OF ELECTRIC SHOCK, NEVER REMOVE TV COVERS, EXCEPT AS SPECIFIED HEREIN. REFER ALL SERVICING NOT SPECIFIED IN THIS MANUAL TO QUALIFIED SERVICE PERSONNEL. Failure to follow this WARNING may result in death or serious injury.

Introduction

Connecting your TV

CAUTION: HOT SURFACE

The temperature of the lamp immediately

after use exceeds 392ûF (200ûC). Touching the lamp before it has cooled will result in severe burns. ALLOW THE LAMP TO COOL FOR AT LEAST ONE (1) HOUR BEFORE REPLACING IT.

3. On the lamp unit door on the side of the TV, loosen the thumb screw by hand or by using a 5/32” or 4mm Allen wrench, and then remove the lamp unit door.

TV back

Thumb screw

Lamp unit door detail

WARNING: RISK OF

ELECTRIC SHOCK! The lamp

unit door is provided with an interlock to reduce the risk of electric shock and excessive ultraviolet radiation. Never defeat its purpose or attempt to service without removing the lamp unit door completely. Failure to follow this WARNING may result in death or serious injury.

4. Using a manual Phillips screwdriver, loosen the two screws on the lamp unit.

Lamp unit screws

(Continued on next page)

62HM14(E)56-60

57

1/24/05, 2:38 PM

Remote Control

Using the

Setting up your TV

Features

Using the TV’s

Appendix

Index

57

(E) 62HM14

Image 57

Contents Dlptm Projection Television Dear Customer Lamp Unit ReplacementInstallation For replacement of the obsolete outletDAMAGE! Never place the TV on Care ServiceThis TV contains several cooling fans to moderate Important notes about your Dlptm projection TVImportant Safety Information Introduction Introduction Welcome to ToshibaExploring your new TV Connecting an antenna or cable TV Connecting your TVConnecting a cable converter box Connecting a VCRUsing You will need Three coaxial cablesConnecting your TV Connecting a cable converter box and VCRConnecting a DVD player or satellite receiver and a VCR From Antenna Stereo VCR From DTV Antenna Connecting a camcorder Connecting two VCRsOne pair of standard analog audio cables One Hdmi cable type a connectorConnecting an audio system Preparing the remote control for use Using the remote controlInstalling the remote control batteries Remote control effective rangeUsing the Remote Control Remote control codesTV/VCR Combo IntroductionDVD/VCR Combo DVD playerCT-90159 Point the remote control Directly at the deviceConnecting YourTV Control Learning about the remote controlSetting up your TV Setting up your TVLearning about the menu system Changing the on-screen display language Selecting the antenna inputPress y or z to highlight your desired language Programming channels automatically Adding channels to the TV’s memoryTo program channels automatically Press Enter Press z to select CH ProgramChanging channels Settingup yourTVSelecting the Quick Restart Adding and erasing channels manuallyUsing the TV’s features Adjusting the channel settingsUsing the TV’s Features Favorite CH Press Enter to displayFavorite CH menu Labeling channels Press z or y to highlightClear Usingthe RemoteControl Settingup YourTV TheTV’s Connecting yourTVUsing Features Appendix Index Press PIC Size on the remote controlTheater Wide 1 picture size For 43 format programs Press Enter to display the Scroll Adjustment mode Press PIC Size to select the Theater Wide 2 or 3 modePress MENU, and then press x or until Picture menu AppearsUsing the Auto Aspect feature Press y or z to highlight Auto ASPECT, and then pressPress y or z to select ON, and then press Enter UsingtheTV’s Features Using the POP double-window featureSwitching the speaker audio main or POP Switching the main and POP picturesDouble-Window aspect ratio Using the programmed channel search functionAbout the auto favorite feature Using the favorite channel search functionUsing the V-CHIP menu Using the Locks menuEntering the PIN code If you cannot remember your PIN codeOFF To release your setting Unlock Enable BlockingTV Rating Independent rating system for broadcasters TV Rating menu appears Press z or y to select an itemSettingup YourTV UsingtheTV’s Features Appendix Index Mpaa Rating Independent rating system for moviesMpaa Rating Unlocking programs temporarily Locking channelsLocks menu Repeat steps 2 and 3 for other channelsPress y or z to highlight Clear ALL, and then press Enter Changing the PIN code Locking the video inputsOFF From the Locks menu, press y or z to highlight NEW PIN CodeAdjusting the picture Selecting the picture modeAdjusting the picture quality Selecting the color temperature Press x or to select the mode you preferSaving your new preferences Resetting picture adjustments Using the CableClear DNR featureReset DoneSelecting the cinema mode Selecting the Lamp modeCinema Mode Press y or z to selectNever Connect this TV to a Personal Computer PC Selecting the video input sourceUsing the closed caption feature Press y or z to highlight Caption or TEXT, and then pressTo view text, highlight T1, T2, T3, or T4 Setting the sleep timer Setting the on timerPress y or z to highlight Sleep TIMER, and then press Press Enter to start the timerTo display the time on-screen Press Recall Setting the clockAdjusting the sound Muting the soundSelecting stereo/SAP broadcasts Adjusting the sound quality Using the WOW surround sound featurePress y or z to adjust the item, then press Enter Press y or z to highlight Audio SETTINGS, and then pressResetting your audio adjustments Using the StableSound featureTo turn off the StableSound feature Select OFF in above Turning off the built-in speakers Selecting the Audio OUT soundTo turn on the built-in speakers Select on in above Understanding the last mode memory feature Understanding the auto power off featureSelecting the background of the menu display Displaying on-screen informationWhen to replace the lamp unit Appendix Lamp unit replacement User-replaceable componentHow to replace the lamp unit Introduction Connecting your TVUsing Setting up your TV Features No picture Dark picture TV will not turn on Replace the thumb screw and hand-tightenUsingthe RemoteControl Settingup YourTV Introduction Connecting YourTVLED indications Lamp unit disposalVIDEO/AUDIO Input SpecificationsTroubleshooting Limited United States Warranty Index 05-01