Toshiba TLP-X11E, TLP-X10Y Lamp replacement, Pull out the lamp, Handle to pull out the lamp

Page 86

Lamp replacement

CONTENTS

86

The lamp will eventually begin to project dark or dull pictures and finally will not light up. (Lamp’s life length depends on the use condition.) In such a case, replace the lamp with new one.

CAUTION

•If you use the projector mounted on the ceiling, ask the dealer to carry out the maintenance such as cleaning or replacement of the lamp.

•When replacing, always use lamp “TLPLX10” (sold separately). For detail, refer to the lamp instruction.

•If you have been using the projector, the lamp will be very hot, and may cause burn injuries. Wait for the lamp to cool (for longer than 1 hour) before replacing it.

•If the lamp should break, please handle with care to avoid injury due to broken pieces and contact your dealer for repair service.

1 Unplug the power cord.

2 Wait until the lamp gets cold enough.

3	Take off the lamp cover on the
	bottom panel.

Loosen two screws, and pull off the lamp cover.

1

Lamp cover

2

4		Pull out the lamp.
4	1	Loosen the two fixing screws, and lift up the
		handle to pull out the lamp.
		2

Maintenance

Continued

Image 86

Contents TLP-X10E Safety Precautions Moisture Condensation Save Original Packing MaterialsAvoid Volatile Liquid Ventilation Power SourcesSource of Light Important Safety Instructions Do not place the product vertically AccessoriesObject and Liquid Entry Stack InhibitedReplacement Parts Important Safety InstructionsDamage Requiring Service ServicingDo not move the projector while the arm is still erect Safety CheckDo not carry by the camera arm Strong light may cause damage to your eyes or sightPower supply cord selection Contents Names of each part on the main unit UseVOL/ADJ buttons 30 41 48 Control connector RS-232C Connector 26 USB connector UseNames of each part on the remote control Laser emission partOpen the cover Install the batteriesLoading batteries Attach the coverRemote control operation BeforeFloor-mounted projector placement Determine the screen size projected on the screen Side viewInsert the other end in a wall outlet Connect the power cordTake off the lens cover Projector placement angle adjustment Turn clockwise to lift up Turn counterclockwise to lowerCeiling-mounted projector placement Installation and connectionConnecting a computer Connecting a computer with DVI output connector Computer in 2 Connector DVI connectorConnecting video equipment RGB2/digital RGB and Y/P B/P R input Projector operation control by a computer How to use the output connector Press ON/STANDBY Playback modeProjection on the screen Turn on the connected equipment and put itSignal sent from the computer Select the input sourcePress VOL/ADJ +/ to adjust volume Adjust the picture size by turningFocusing ring Zooming leverPress ON/STANDBY again Turning the power offPress ON/STANDBY after using the projector Adjusting the picture automatically Press Auto SETCorrecting the keystone distortion Press Auto KeystonePress Mute Remote controlCutting off the picture and sound temporarily OperationsPress Freeze Icon Appears in the freeze modeFreezing the picture Picture freezesPress Resize Icon Appears in the resize modeEnlarging the picture size Sub-picture is displayed Displaying PIP Sub-picturesPress PIP Information described below is displayed Displaying InformationPress Call Pressed againOperating a computer by the remote control Projecting images stored in a memory card About memory cardsInsert the memory card into the card slot Press Input repeatedly to select the memory card inputUse VOL/ADJ +/ to change pages. Remote control Control panelDescription of screen ChangingPress Exit Press ENTER. Slide displayPress VOL/ADJ +/-. Slide transition Projecting images stored in a memory card To eject the memory cardAdjustments and settings on the menu screen Quick MenuAdjustments and settings on the menu screen Operating the menu screen StartQuick Menu appears Quick Menu adjustments and settingsPress Menu Types of adjustment and setting items are different See the table belowLamp power Press VOL/ADJ +/ to adjust and setPicture mode Analog RGB input, digital RGB input Auto. demo Memory card inputPress VOL/ADJ +/- to select the type of input source Sub-menu screen of input source setting appearsPress Enter Press Exit to return to the Quick MenuUse the selection buttons / to select a language Menu screen disappears Sub-menu screen of interval setting appearsUse the selection buttons / to select interval time Press Menu twice Full Menu adjustments and settings -PictureAdjustments Full Menu adjustments and settings Picture Screen size Picture mode RGB inputInput select mode Memory card input Slide show Memory card inputPress Exit to return to the Full Menu Sub-menu of selected items appears PositionLevelVideo mode Video input, S-video input Use the selection buttons / to select setting itemsSignal format Y/PB/PR input Sub-menu of selected items appearsFull Menu adjustments and settings Picture Full Menu settings Audio Channel select After the settings are finished, press ExitSpeaker output LoudnessUse the selection buttons To display Keystone menu Full Menu settings KeystoneUse the selection buttons To select Setting items Press Exit several times until the menu screen After the adjustments and settings are finishedUse the selection buttons / to select Yes and press Enter DisappearsWhen pressed once, the Quick Menu screen appears. When Full Menu settings DisplayUse the selection buttons To select Setting items Settings Use the selection buttons To display Display menuWhen selecting Language in step Menu background translucent No signal background Setting of screen of no signal inputMenu position Start-up screenWhen pressed once, the Quick Menu screen appears. When Full Menu settings Default settingUse the selection buttons To display Default setting menu Sub-menu of Input source setting appears Control panel Main unit sideRear ceiling Ceiling-mounted rear projection Use the selection buttons / to select the projection modeSub-menu of Projection mode appears Press VOL/ADJ +/ to set No signal power offPower on Picture menus for the each input to Full Menu settings Factory reset modeFactory default setting Full Menu settings Factory reset mode Audio Set the audio input source PIP menu settingSize Set the PIP sub-picture size Menu screen disappearsPart names of the document imaging camera model Preparation of the document imaging camera Camera control panel Press ARM LightSet a document to be projected Light turns onPress Camera to select the camera input mode Move the camera head to adjust the size PictureFollow the steps of Preparation of the document imaging Press Camera Gain +/- to improve view of aCamera subject which is too dark or vivid Camera in reverseProject a white paper and enlarge it to fill Balance Press W.BALANCE to turn the Lock indicatorLock the white balance ScreenCover the camera lens with a piece of black Correcting illuminated defectsWith the document camera operating, fully Paper or clothStore the camera images into the memory card Power turns off or does not come on IndicatorPower does not come on Trouble indicationsClean the air filter Air filter cleaningUnplug the power cord Take off the air filter coverAssemble the air filter Air filter cleaningInstall it Mount the air filter coverCleaning the main unit Lens and main unit cleaningCleaning the lens Replacing the intake, exhaust fans and air filterLoosen two screws, and pull off the lamp cover Lamp replacementPull out the lamp Handle to pull out the lampAttach the lamp cover Reset the lamp timerLoad a new lamp Slide the cover in place and tighten two screwsBefore calling service personal Symptom Cause CorrectionBefore calling service personal Pin assignment of Computer IN, Monitor OUT connector Applicable signal Applicable RGB signalApplicable signal Compatible video signalControlling the projector by using RS-232C Signal assignment of RS-232C Interface formatControlling the projector by using RS-232C AS1 MB1 VLU Auto SET USB output Type B SpecificationsMini DIN 8-pin RS-232C Specifications Replacement lamp