Toshiba 30HFX85 appendix Searching and sampling the code of a device

Page 19

Programming the remote control for use with your audio/video devices

Device code setup

1.Refer to the Device code table on pages 21–22 to find the code for your device.

If more than one number is listed, try each one separately until you find one that works.

2.Press MODE until the Mode indicator for the device (CABLE/SAT, VCR, DVD, AUDIO1, AUDIO2) lights up.

3.While holding down the RECALL button, press the Channel Number buttons to enter the four-digit code of your blank of device.

If a valid code is entered, the mode indicator will blink twice.

If an invalid code is entered, the mode indicator will blink one long blink.

4.Point the remote control at the device and press POWER to test the code. If the device turns on, you have entered the correct code.

If the device does not respond to the remote control, you may have entered the wrong code. Repeat steps 3 and 4 using another code.

5.Press MODE to select the TV mode to control the TV.

Searching and sampling the code of a device (8500)

If you do not know the device code for a particular target unit, you can cycle the remote control through the available codes for that device mode and sample the functions to find the code that properly operates the target device. The keys available to be sampled, provided they are applicable to that mode, are 0, 1, 2, 3, POWER, VOL 5, CH 5, PLAY and STOP. Invalid keys will be ignored while in program mode.

To cycle through each available device code and sample its functions:

1.Press MODE to select the mode you want to set up.

2.While holding down the RECALL button, press 8 –5 –0 –0. The remote control will enter program mode.

3.Point the remote control at the target device and press POWER (or other function buttons that are available to be sampled).

4.If the device responds to the remote control:

Press RECALL to store the device code.

The mode indicator will blink twice and the remote control will exit the program mode.

If the device does not respond to the remote control: Press 5, and then press POWER.

Repeat this step until the device responds to the remote control, and then press RECALL.

Note: When a search cycle is completed, the mode indicator will blink three times. The remote control will begin to cycle through the available codes again. If no key is pressed within 10 seconds while programming, the remote control will exit the program mode and return to the previous code.

Notes:

•Every time you replace the batteries, you must reprogram the remote control.

•Some newer VCRs are capable of working on either of two remote codes. These VCRs have a switch labeled “VCR1/VCR2.”

If your VCR has this kind of switch and does not respond to any of the codes for your VCR brand, set the switch to the other position (VCR1 or VCR2) and reprogram the remote control.

POWER

NUMBERS

MODE

5

RECALL

Safeguards

Important

ToshibaWelcome to

yourConnecting TV

Remote ControlUsing the

your TVSetting up

FeaturesUsing the TV’s

19

Appendix

J3S40321A(E)_P16-26

19

12/07/2005, 8:40 AM

Page 18 Page 20
Image 19
Page 18 Page 20
Contents 30HFX85 Child Safety Important Safety Instructions Faded. If this happens, turn off the TV for 6 to 7 hours to Temperature rises suddenly for example, when the TV isFor added protection of your TV from lightning and power Damage is not Covered by Your WarrantySetting up your TV Important Safety Information Welcome to ToshibaConnecting your TV Using the remote controlTV front panel Welcome to ToshibaExploring your new TV Selecting a location for the TVConnecting a VCR Connecting your TVStereo VCR Converter/Descrambler Splitter Switch Connecting a cable converter box or AntennaFrom Cable Connecting a DVD player/satellite receiver and a VCR DVD player with Component video DTV Receiver With Component video Connecting your TV Connecting two VCRsConnecting a camcorder To connect a DVI device, you will need Connecting an Hdmi or a DVI device to the Hdmi inputAmplifier Connecting an audio systemYou will need One pair of standard audio cables Mode Device Using the remote controlPreparing the remote control for use Installing the remote control batteriesRemote control functional key chart Record Disc shiftDisc shift Deck side StopSearching and sampling the code of a device Press Mode to select the TV mode to control the TVOperational feature reset Using the volume lock featureDevice code table VCR setup codesCD Player setup codes Learning about the remote control Starting setup Setting up your TVChanging the on-screen display language Adding and erasing channels manually Image tilt correctionAdding channels to the TV’s memory Programming channels automaticallyChanging channels Using the TV’s featuresAdjusting the channel settings Switching between two channelsTo clear your favorite channels Using the Locks menuSelecting a password To select your password and access the Locks menuUsing the V-Chip parental control feature To unlock channels Locking channelsTo lock channels Press Enter . Repeat steps 1 through 6 to lockLocking the video inputs Setting the GameTimerTMLabeling channels Using the front panel lock featureLabeling the video input sources Selecting the video input sourceTo label the video input sources Select Left and right edges are This mode cannot be scrolledCenter of the picture remains Close to its original proportion, butFull picture size for 169 source programs TheaterWide 2 picture size for letter box programsTheaterWide 3 picture size example To lower the picture, press Press or to display the Scroll Adjustment modeScrolling the TheaterWide picture TheaterWide 2 and 3 only To raise the picture, pressUsing the Aspect feature Selecting the cinema modeSelecting the display format for 480p signals only To adjust the picture quality Adjusting the picture Selecting the picture modeAdjusting the picture quality To select the picture modeUsing the CableClear feature Selecting the color temperatureSelecting the Scan Velocity Modulation SVM Setting the sleep timer Resetting your picture adjustmentsUsing the closed caption feature Selecting stereo/SAP broadcasts Adjusting the sound Muting the soundAdjusting the sound quality To adjust the sound qualityUsing the StableSound feature Resetting your audio adjustmentsUsing the BBE sound feature Selecting the Hdmi audio input source Turning off the built-in speakersDisplaying TV status information on-screen Symptom Solution Auto power offUnderstanding the Power Return feature TroubleshootingSpecifications Limited United States Warranty Memo National Service Division
Top Page Image Contents