Toshiba D-R160SB manual Installing batteries in the remote control, About the remote control

Page 19

Introduction

Preparation of the remote control

Introduction

Installing batteries in the remote control

■Install two R6 (AA) batteries (supplied) into the remote control, carefully match with the polarity indicated inside the battery compartment.

1Open the cover.

2 Insert batteries.

Make sure to match the + and - on the batteries to the marks inside the battery compartment.

3 Close the cover.

Notes:

•Incorrect use of batteries can result in hazards such as leakage and bursting.

•Do not mix new and old batteries together.

•Do not use different kinds of batteries together.

•Make sure that the + and - ends of each battery match the indications inside the battery compartment.

•Remove batteries if the remote control will not be used for an extended period of time.

•When disposing used batteries, please comply with governmental regulations or the public instructions for environmental protection that apply in your country or area.

•Do not recharge, short-circuit, heat, burn or disassemble batteries.

About the remote control

■Keep in mind the following when using the remote control:

●Make sure there is no obstacle between the remote control and the remote control sensor on the unit.

●Use within the operating range and angle as shown.

●Remote control operation may become unreliable if the remote control sensor of the unit is being exposed by the strong sunlight or fluorescent light.

●Remote controls for different devices can interfere with each other. Be careful when using remote controls for other equipment located close to the unit.

●Replace the batteries when the operating range of the remote control reduces.

●The maximum operable range as follows:

-Line of sight: approximately 7 m

-Either side of the centre: approximately 7 m within 30 degrees

I/y

Connections Basic Setup Recording Playback

Editing Function Setup Others

EN 19

Image 19

Contents R160SB Basic Introduction PrecautionsLaser Safety Power SupplyMains Cord Connection to PowerDeclaration of Conformity Make your contribution to the environmentMoisture Condensation Warning Installation LocationAccessories Supplied Avoid the Hazards of Electrical Shock and FireCleaning the Unit MaintenanceTable of contents Editing Function SetupTroubleshooting Language code Glossary Specifications PlaybackCompatibility FeaturesDVD disc types Using different disc types for different purposesDisc Mark Specification Remarks Choosing a discIntroduction Choosing a disc cont’d Disc Mark Specification Remarks DVD video10 EN For playback onlyStandards On DVD-R discsOn DVD-RW discs Marks on DVD video discsYes No Yes12 EN Discs and purposes Front Panel Index to parts and controls7 8*9 14 ENRear Panel Introduction Index to parts and controls cont’d 16 ENNumber buttons Timer PROG. buttonSetup button OPEN/CLOSE a buttonFront Panel Display Guide 18 ENDisplay message 1Open the cover Insert batteries Installing batteries in the remote controlAbout the remote control Keep in mind the following when using the remote controlOn Screen menu Display menu Setup menus20 EN Format DVD-RW only DVD-RW VR modeDisc Protect VR mode only CD, MP3, JPEG, Video CDPage Connections 24 EN ConnectionsAV3RearAV4Front Connecting to external equipmentDigital audio for better sound quality 26 ENAfter you have completed connections Basic Setup 28 EN Initial settingBasic Setup Press Enter to start Channel TuningAuto tuning Channel settingManual tuning Move To skip a Preset channelFollow steps 1 to 3 in Manual tuning on 30 ENAuto Clock Setting Setting the clockManual Clock Setting 32 EN Press Setup to exit the Clock menuIf you have a standard TV Select TV Aspect using K / L, then press EnterSelect the desired option using K / L, then press Enter Selecting the TV aspect ratioPage Recording Information Recording ModeInformation on DVD recording 36 ENMaking discs playable in other DVD player Finalise What is CPRM?Restrictions on recording Information on copy controlChoosing the recording format of a blank disc Select Format using K / L, then pressSelecting the Recording format 38 ENFormatting is complete Select Format Mode using K / L, then press EnterSelect Video mode or VR mode using K / L, then press Enter Press Setup to exit Insert a blank disc40 EN Reformatting a disc Setting Auto ChapterRecording Audio Select XP Selecting the Sound modePress Setup Select Recording using K / L, then press Enter Select PCM or Dolby Digital using K / L, then press EnterSelect Stereo or Bilingual using K / L, then press Enter Select External Input Audio using K / L, then press Enter42 EN Basic recording Select the recording mode using REC ModePress I/y ON/STANDBY to turn on the unit Recording Basic recording cont’d 44 ENPress REC I to start recording Press Stop C to stop the recordingHas enough space remaining for the time you set One-touch Timer Recording46 EN Recording One-touch Timer Recording cont’dTimer Programming list will appear Timer RecordingStop mode, press Timer Prog Select a programme using K / L, then press48 EN Enter the date using K / L, then press BEnter the time to start and to end using Recording Timer Recording cont’dSelect PDC to on or OFF using K / L. See Select the recording mode using K / L, then press B50 EN Press Enter when all information required is enteredPress I/y ON/STANDBY Press Clear to erase the selected programme If the timer programming did not complete correctlyTo correct the timer programming Error numbers indicatePDC Programme Delivery Control Hints for Timer RecordingPriority of overlapped settings 52 ENIf the recording time is partially overlapped Satellite LinkIf the recording time entirely overlaps 54 EN Connection to an external equipment Select Select Video using K / L, thenSelect the input jack type to be used using Press Setup to exitBefore recording from external equipment, see Recording Settings for an external equipment cont’d56 EN Recording from an external equipmentSEP SLP EP Select a recording mode using REC MODE. See58 EN Setting disc protectionFinalising discs Select Finalise using K / L, then press EnterFinalising is complete Select Yes using K / L, then press EnterTo cancel finalising DVD-RW only 60 ENSelect on using K / L, then press Enter Select Auto Finalise using K / L, then press EnterAuto finalise Page Playback 64 EN Basic playbackPlaying back a DVD-RW / DVD-R Menu / List Press TOP Menu to display the Title menuPress Stop C to stop playback Select the desired title using K / L/ / BSelect Play using K / L, then press Enter 66 ENPlaying back a DVD-VIDEO / Video CD / CD