Ultratec 61UDX10B SET-TOP-BOX STB button, Precoded SET-TOP-BOX/SATELLITE Receiver buttons

USING THE REMOTE TO CONTROL

SET-TOP-BOX/SATELLITE RECEIVER FUNCTIONS

Operating the precoded function for your set-top-box/satellite receiver.

This remote is designed to operate different types of set-top-box/satellite systems. You must first program the remote to match the remote system of your set-top-box/satellite systems. (refer to page 32)

1.Turn ON your set-top-box/satellite systems.

2.Aim the remote control at the front of your set-top-box/satellite systems.

3.Press and release the SET-TOP-BOX (STB) button to switch to set-top-box/satellite pre-coded mode.

4.Hold down the STB button on the remote and enter the two digit preset code that matches your set-top-box/satellite receiver as shown on page 32. The indicator light will flash 3 times if the code was accepted.

5.Aim the remote at the set-top-box/satellite receiver and press the POWER button. The remote will turn off your set-top-box/satellite receiver when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your set-top- box/satellite receiver. If the set-top-box/satellite receiver does not turn off, try a different two digit preset code.

6.The remote will now control your set-top-box/satellite receiver.

NOTES:

1.If your set-top-box/satellite receiver cannot be operated after performing the above procedures, your set-top- box/satellite receiver code has not been precoded into the remote.

2.In the unlikely event that your set-top-box/satellite receiver cannot be operated after performing the above procedures, please consult your set-top-box/satellite receiver operating guide.

3.The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above.

4.The ANT button will act as the TV/STB button when in STB mode.

aSET-TOP-BOX (STB) button

This button allows the remote to control your satellite receiver by setting it to SET-TOP-BOX/SATELLITE mode.

b PRECODED SET-TOP-BOX/SATELLITE RECEIVER buttons

These buttons transmit the chosen precoded set-top- box/satellite codes.

b

b

c c

c

POWER								b
TV	VCR		CBL		STB		a
	SOURCE WIZARD
DVD	AV1		AV2		AV3
1		2		3
4		5		6			b
7		8		9
SLEEP		0			LAST CH
C.C		HELP	ASPECT		PIX
ANT							c	b
	MENU		EXIT				b
VOL	SELECT			CH			b	c
SVCS	MUTE	STATUS		SCHD			c	c
VCR	PLUS+
							b
VID1		INFO	GUIDE/TV		VID	5
VID 2		VID 3	VID	4
PIP	PIP CH			FREEZE
		PIP ACCESS						c
PIP MODE	SWAP
PROG	TV/VCR			SLOW

REC

POWER

TV	VCR			CBL		STB		a
	SOURCE WIZARD
DVD	CD			TAPE		AMP
1			2		3
4			5		6			b
7			8		9
SLEEP			0			LAST CH
C.C			HELP	ASPECT		MODE
ANT								c
	MENU		EXIT					b
VOL	SELECT				CH			b
SVCS	MUTE		STATUS		SCHD			c
VCR	PLUS+
								b
VID1			INFO	GUIDE/TV		VID	5
VID 2			VID 3	VID	4
PIP		PIP CH			FREEZE
			PIP ACCESS
PIP MODE		SWAP
PROG	TV/VCR				SLOW

REC

cEXCLUSIVE TV buttons

These buttons are for operating the TV.

CLU-5711TSI CLU-5713TSI

MY SATELLITE RECEIVER/STB CODE IS:

NOTE: Refer to instruction manual of the set-top-box/satellite receiver for operation of the buttons exclusively for the set-top- box/satellite receiver.

29