TV set up by library search, Operating the RC027

9.If the Device Code does not work properly on your TV, press the TV INDICATOR KEY once. The STATUS INDICATOR LED will flash briefly, and remain lit. The TV INDICATOR key should still be lit. (If either of the indicators switch off whilst you are still programming your RC027, you should start again from step 3.)

10.Repeat steps 7-9 with the other codes listed for your brand of TV until your RC027 operates most or all of the functions that correspond with the keys on your original remote control.

11.Once you have found a suitable code, to store it, press the TV INDICATOR key twice. The TV INDICATOR key will flash twice and then go out as will the STATUS INDICATOR LED.

12.If none of the TV codes listed for your brand of TV work correctly, select the code that provides the best results. Alternatively, try the Library Search method, which is fully explained further on in these instructions.

If you cannot identify a suitable Device Code for your equipment from the Device Code List and have been unable to store a code when using Auto Code Search you may try our library search method. (For many lesser known brands codes may be present but not listed under that brand.) During the search the selected DEVICE INDICATOR will flash at various speeds. The entire search procedure may take several minutes to complete. The following instructions use your television as an example for set-up using the Manual Code Search method.

TV set up by library search

1.Turn on your TV

2.Hold down both POWER and MUTE keys on your RC027 simultaneously until the STATUS INDICATOR LED lights up and stays blue (about 4 seconds).

	Blue Status Indicator
TV Device
Indicator key	Step 6
	Step 6

Step 4

Step 8

Step 2

Step 7

3.Release the POWER and MUTE keys The STATUS INDICATOR should still be lit. If not repeat step 2.

4.Press the TV key once. The STATUS INDICATOR and the DEVICE INDICATOR should now both be RED.

5.To search, aim your RC027 at your TV.

6.Press the POWER key repeatedly for 2 seconds ON and two seconds OFF, until your TV goes into standby mode (i.e. the TV switches OFF). Then continue with step 7.

If the TV INDICATOR key flashes twice and then goes out

before your TV goes into stanby mode you have reached the end of the code library. Return to step 2 and repeat library search one more time.

7.Try the number keypad to see if your device switches ON again and the keys work correctly. If your device does not switch ON, press the Mute key and then the Power key to repeat the code so that the TV comes ON. Now try the number keypad. (NOTE: If you accidentally skipped a code that turned your TV ON or OFF, you can return to the skipped code by pressing the Mute key.)

8.If the code you have found does not work correctly, make sure that the TV key and STATUS INDICATOR LED are still lit, before you repeat steps 6 and 7 until you find a better code. If the indicator lights have gone out, repeat the set-up procedure from step 2.

9.Once you are happy with the code found, press the TV key once to store the code. The STATUS INDICATOR LED and TV key LEDs will turn off and set-up is complete.

Operating the RC027

Once you have set up your RC027, it should operate similarly to your original remote control and perform most or all of the main functions. To operate, just aim it at your equipment, press the appropriate DEVICE INDICATOR key and press the required function key. The DEVICE INDICATOR flashes during signal transmission to confirm that a function key is in operation.

Please Note: The RC027 can only duplicate functions that are on your original remote control. Any extra keys on the RC027 which are not on the original will not function.

TV code recall - 888

The RC027 has a special code which can be entered to find the code that has been set for your TV. ( e.g. after Code Search set ups)

1.Press POWER and MUTE keys together until Status Indicator blue LED lights up and flashes 3 times.

2.Then press the TV key, Status Indicator LED & TV key will light up Blue.

3.Key in Device Code Recall code 888.

•To find the first digit of your code, press 1 and then count the number of times the Status Indicator LED flashes blue.

•To find the second digit of your code, press 2 and then count the number of times the Status Indicator LED flashes blue.

•To find the third digit of your code, press 3 and then

count the number of times the Status Indicator LED flashes blue.

[Note: If the Status Indicator LED does not flash at all the digit is zero (duration between flashes is 1 sec.)]

E.G. Code=106, Number 1=1 flash, Number 2=no flash, Number 3=6 flashes.

5.Press the TV Device key once to exit Device Code Recall.

(Note that the RC027 will exit the Recall procedure if no key is pressed for 30 seconds)