SETUP BY ENTERING DEVICE CODE
( Note: If you do not touch any keys on your URC within 10 seconds during
SET UP FOR TV
1.Turn on your TV
2.Look up the brand name of your TV in the DEVICE CODE LIST (See page
3.Look up the
4.Hold down both 
POWER and 
MUTE keys on your URC simultaneously until the STATUS INDICATOR lights up and stays red (about 4 seconds).
Figure 1.DEVICE INDICATOR
twice and then go out as will the STATUS INDICATOR.
12.If none of the TV codes listed for your brand of TV work correctly, select the code that provides the best results. Alternatively, try the Library Search method, which is fully explained further on in these instructions.
SET UP FOR VCR AND SAT
Repeat the same
SET UP FOR AUX KEY
The following instructions describe how to configure the AUX key to act as a 2nd TV/VCR/SAT control.
13. First use the TV/VCR/SAT | ||
best code for the device you wish to program into the | ||
AUX key following steps | ||
14. Wait until all indicator lights have gone out then hold | ||
down the | POWER and | MUTE keys together on |
your URC, | until the STATUS | INDICATOR lights up and |
STATUS INDICATOR
Steps
KEYS
stays red. [About 4 seconds] |
| |
15. Release the | POWER and | MUTE keys. The STATUS |
indicator should still be lit. If not repeat step 14. | ||
4.& 14. 
5.Release the 
POWER and 
MUTE keys. The STATUS
indicator should still be lit. If not repeat step 4.
6.Press the TV DEVICE INDICATOR key once. The STATUS INDICATOR and the DEVICE INDICATOR should now both be RED.
Figure 2. | Step 16. |
|
Step 6.
7.Use the number keys on your URC to enter the
Figure 3.
Step 7.
8.Try the keys on your URC that correspond to similar keys on your original remote control, especially those you use most. (Note that the URC will abandon the
more than 10 seconds). If your TV works on all or most of the keys on your URC, you have entered a suitable Device Code. Go to step 11. (Note: Your URC will only operate functions controlled by your original remote nor are the supplied codes guaranteed to operate all these functions)
9.If the Device Code does not work properly on your TV, press the TV INDICATOR KEY once. The STATUS INDICATOR will blink briefly, then turn RED. The TV INDICATOR should still be RED. (If either of the indicators switch off whilst you are still programming your URC, you should start again from step 3.)
10.Repeat steps
11.Once you have found a suitable code, to store it, press the TV INDICATOR key twice. The TV INDICATOR will blink
16. Press the | AUX | DEVICE INDICATOR | key | once. |
(AUX INDICATOR should turn RED) |
|
| ||
17. Press briefly the TV or VCR or SAT DEVICE INDICATOR | ||||
corresponding to the type of device you are | ||||
programming into the AUX key. |
|
| ||
18. Type in the 3 digit code that you found in step 13. | ||||
19. Press the AUX key twice to store your code. If you have | ||||
followed the | instructions correctly, | the | SATUS | |
INDICATOR and DEVICE INDICATOR will turn off. Set up is now complete.
SET-UP BY LIBRARY SEARCH
If you cannot identify a suitable Device Code for your equipment from the Device Code List, you may try our library search method. (For many lesser known brands codes may be present but not listed under that brand.) During the search the selected DEVICE INDICATOR will flash at various speeds. The entire search procedure may take several minutes to complete. The following instructions uses your television as an example for
TV SETUP BY LIBRARY SEARCH
1.Turn on your TV
2.Hold down both 
POWER and 
MUTE keys on your URC simultaneously until the STATUS INDICATOR lights up and stays red (about 4 seconds).
3.Release the 
POWER and 
MUTE keys The STATUS INDICATOR should still be lit. If not repeat step 2.
Figure 4. | DEVICE INDICATOR |
STATUS INDICATOR | KEYS |
|
Steps
2. & 10.
4.Press the TV DEVICE INDICATOR key once. The STATUS INDICATOR and the DEVICE INDICATOR should now both be RED.
Figure 2. | Step 11. |
|
Step 4.
5. To search, aim your URC at your TV.
3