NAD T 533 Sound Digital Audio Output, Sample Frequency, Speaker Settings DVD-VDVD-A, Volume, Size

ENGLISH FRANÇAIS DEUTSCH NEDERLANDS ESPAÑOL ITALIANO PORTUGUÊS SVENSKA

Preparation

BEFORE OPERATION

SOUND

DIGITAL AUDIO OUTPUT

Each DVD disc has a variety of audio output options. Set the player’s Digital Audio Output according to the type of audio system you use. DOLBY DIGITAL/PCM: Select “DOLBY DIGITAL/PCM” if you connected the DVD Player’s DIGITAL OUT jack to a Dolby Digital decoder (or an amplifier or other equipment with a Dolby Digital decoder). Stream/PCM: Select “Stream/PCM” if you connected the DVD Player’s DIGITAL OUT jack to an amplifier or other equipment with a DTS decoder, Dolby Digital decoder or MPEG decoder.

PCM: Select when connected to a 2-channel digital stereo amplifier. The DVD player outputs sounds in the PCM 2channel format when you play a DVD video disc recorded on the Dolby Digital, MPEG1, or MPEG2 recording system.

Disc Audio	DIGITALDOLBY /PCM
Disc Subtitle	Stream/PCM
Disc Menu	PCM

Rating

Country Code

Sample Freq.

TV Aspect

48 KHz

Menu Language

96KHz

Progressive Scan

Digital Audio Output

5.1 Speaker Setup

Others

SAMPLE FREQUENCY

To change the Sample Frequency setting, first select the desired Digital Audio Output as indicated as above.

If your receiver or amplifier is NOT capable of handling 96 KHz signals, select 48 KHz. When this choice is made, this unit will automatically convert any 96 KHz signals to 48 KHz so your system can decode them. If your receiver or amplifier is capable of handling 96 KHz signals, select 96 KHz. When this choice is made, this unit will pass each type of signal through without any further processing.

5.1 SPEAKER SETTINGS DVD-VDVD-A

Select speaker settings, including volume balance and delay time, or test the speaker settings. Speaker settings are only active on the Analog Multi- Channel Output.

Disc Audio

Disc Subtitle

Disc Menu	R	R
	Front L
Rating
Country Code	Volume	0 dB
	Size	Large
TV Aspect
Menu Language	Distance	1 ft
Progressive Scan	Test
Digital Audio Output	Return
5.1 Speaker Setup
Others

Make the following settings for the built-in 5.1 channel surround decoder.

1Select “5.1 Speaker Setup” using the buttons on the setup menu.

2While “5.1 Speaker Setup” is selected, press > button.

3Press buttons to select the desired speaker.

4Adjust options by using buttons.

SPEAKER SELECTION

Select a speaker that you want to adjust. (Front speakers (Left), Front speakers (Right), Center Speaker, Rear speakers (Left), Rear speakers (Right), or Subwoofer)

NOTE

Certain speaker settings are prohibited by the Dolby Digital licensing agreement.

VOLUME

Press to adjust the output level of the selected speaker (from 0dB to -10dB).

SIZE

•Press to set a mode (Large, Small or None).

•If you have connected your system to a speaker with a low frequency roll-off of below 100 Hz, select “Large.”

•If you have connected your system to a speaker with a low frequency roll-off above 100 Hz, select “Small.”

NOTE

If you have not connected a subwoofer, always select “Large” for Front speaker (L/R).

•When you do not have a speaker connected, select “None.”

•Front L/R speaker’s size may be set to “Large” or “Small.”

•If Front L/R speaker’s size is set to “Small,” Rear and Center speaker’s size may be set to “Small” or “None.”

•Subwoofer’s size may only be set to “Large” or “None”

DISTANCE

If you connected speakers to your DVD Player, setting the Distance lets the speakers know how far the sound has to travel to reach your set listening point. This allows the sound from each speaker to reach the listener at the same time. (1 ft = 30.48 cm)

TEST

Press ENTER to test the levels of each speaker. Adjust the volume of each speaker so that the volume levels are the same, relative to your viewing position. The speakers are selected in turn as follows:

Front Left (L) ➜ Center ➜ Front Right (R) ➜ Rear Right (R)

➜Rear Left (L) ➜ Subwoofer

RETURN

Press ENTER to return to the previous menu.

14