Integra DHS-8.8 manual Connecting to a TV, Via Hdmi input, Via component video input

Page 14

Preparation (Continued)

Step 1: Connecting to a TV

•Connect the player directly to your TV. If you connect the player to a VCR, TV/VCR combination, video selector or AV amplifier, the playback picture may be distorted due to copy protection.

•Be sure to turn off the power and unplug both units from the wall outlet before making any connections.

Via HDMI input

To view 1080p output, make this connection.

HDMI transfers digital audio and uncompressed digital video on a single cable. As a result, audio cables and video cables don’t need to be connected separately to a device.

($-) CABLE NOTBSUPPLIED

4OO($-) /54($-) ).054

46

Notes

•When the HDMI connection is not verified, an error message appears on the front panel display. In this case, disconnect the HDMI cable then connect it again, or turn off the connected HDMI device then turn it on.

•HDMI output is digital only, DVI analog is not supported.

•HDMI is an evolving technology, so it is possible that some devices may not operate properly with this player.

•To get the most possible benefit from Dolby Digital Plus, you should connect your HD DVD player to your AV receiver using its HDMI input. If your AV receiver has this type of input, make sure it is connected to your HD DVD player and that the input is set to use audio from HDMI (and not the SPDIF coaxial or optical input). If your AV receiver does not have an HDMI input, then the next best choice is to use the SPDIF (coaxial or optical) input on your AV receiver.

•If you use the SPDIF (coaxial or optical) output or analog outputs to connect your audio system and have the “Digital Out HDMI”

( page 22) set to “Auto” or “PCM”, the audio output level from these jacks will be reduced when listening to a multichannel disc. To restore the audio output level, set “Digital Out HDMI” to “Downmixed PCM”.

•Be sure to confirm compatibility of a cable when connecting a Deep Color compatible display device.

When the output resolution ( page 21) is set to “up to 1080p/24Hz”, Deep Color output is disabled.

Via component video input

Some discs may be down converted or require HDMI connection.

Not compatible with 1080p. To view 1080p output, select HDMI connection.

#OMPONENTOVIDEONCABLES NOT SUPPLIED

4OO#/-0/.%.4 6)$%/$/54054

9 0" 02

46

This connection only sends video signals. Be sure to make audio connection on page 15.

Note

•This player supports simultaneous output of video on its HDMI and component video ports. However, some discs may restrict output of video on the component video ports when viewing high definition content or up-converted DVD content. The resolution on the HDMI output will be the same as the resolution output on the component video output. Thus, because the HDMI output can change automatically to match the maximum available resolution of your display, if you connect both the HDMI output and component output, the resolution on the component output will change if the HDMI output auto-adjusts.

14

DHS-8.8_En.indb 14

2007/10/09

18:16:43

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Page 13 Page 15
Image 14
Page 13 Page 15
Contents $3 Important Safety Instructions Power Installing this UnitPrecautions FCC Information for UserTable of contents Disc compatibility FeaturesDisc Specification DVD-Video regions About the volume levelImportant notes about HD DVD Playback restrictionsCustomer support HD output jacksCertain system requirements Rear panel Index to parts and controlsFront panel Remote control DisplaySupplied accessories AccessoriesRemote control Loading batteriesRelease TV Code To program the remote control to operate your TVTV control G 4OOENTERNResolution and connections PreparationVia component video input Connecting to a TVVia Hdmi input To view 1080p output, make this connectionVia Hdmi output Connecting to audio systemVia S Video or Video yellow input Via digital audio outputUDIOVIDEO Cable SUPPLIED Via 5.1ch analog audio outputVia analog audio output Roadbanddmodem 2OUTER LAN connection0RESSEDOWN to Remove Ockkportion Turn on the TV or monitor, and select Power connectionPowering on Input which the player is connected toSetting up the player LanguageFtertsettingsthis Item Press  TimeFor best viewing of film movie material 24p output ResolutionPress / to select Picture, then press OK Video OUTPUT Settings and actual output resolutionH2ESOLUTIONL3ETTINGv   PAGEE Audio output Press / to select Audio, then press OKFront Left / Front Right When a 2ch stereo system is connected to this playerCrossover Setting Center / L Surround / R Surround4OOADJUST the PLAYERSSCLOCKLVIACTHE Network Time PROTOCOL EthernetYour player is ready Playing Playing a discTo resume playback from the location last stopped To pause playbackTo stop playback Basic operations tableTo select the camera angle To select subtitlesTo select the sound To play repeatedly To locate a positionTo check the current status C/D buttons Requirements for HD DVD discs/Web-enabled network contentHD DVD playing options in the future Cursor controlsOutput sound conversion table ADVCustomizing the function settings TV Shape 169 SettingsPicture Letter BoxAudio Language Language code list How to select a languageEthernet GeneralUpdate Firmware Remote Controller SoundMaintenance Initialize UpdateBefore calling service personnel Symptom RemedyH i b i t a USAAbove, provided that you also meet all of these conditions No Warranty H i b i t B GNU Lesser General Public License Version 2.1, FebruaryDHS-8.8En.indb 2007/10/09 No Warranty H i b i t D License IssuesH i b i t C Specification Memo Memo DHS-8.8En.indb 2007/10/09 
Top Page Image Contents