Samsung DVD-C700 manual Surround Sound Speaker Setup C700 only, Setting Up Display Options

DVD

Surround Sound Speaker Setup (C700 only)

The DVD-C700 has a Speaker Setup feature that allows you to customize your surround sound setup.

DDVVDD

Setting Up Display Options

1.Press the SETUP button in play or stop mode.

Press the UP/DOWN button to select AUDIO

2.OPTIONS. Then press the ENTER button.

Use the UP/DOWN button to select SPEAKER

3.SETUP. Then press the ENTER button.

SPEAKER SETUP

4.Use the UP/DOWN or LEFT/RIGHT button to select the desired item. Then press the ENTER button.

5.Use the UP/DOWN button to select speaker mode desired. Then press the ENTER button.

Setting up SPEAKER MODE

• If you have connected the system to a speaker with low fre-

quencies of 100Hz or below, select ‘Found(Large illustration)’.

• If you have connected the system to a speaker without low fre-

quencies of 100Hz or below, select ‘Found(Small illustration)’.

If you don’t connect a subwoofer, always select ‘Found(Large

illustration)’ for the Front Speakers(L/R).

• When you don’t have a particular speaker connected, select

	1.Press the SETUP button in play or stop mode.
	1.
	Use the UP/DOWN button to select DISPLAY
	2.OPTIONS. Then press the ENTER button.
	2.
	Use the UP/DOWN button to select the desired
	3.item. Then press the ENTER button.
	3.
		DISPLAY OPTIONS
1	1	TV ASPECT	WIDE
	2	ANGLE MARK	ON

Speaker Mode	Channel
(Front L)	Balance
	(Center)
	OdB
TEST

Speaker Mode

(Center)

Delay Time

(Center)

Oms

Channel

Balance

(Subwoofer)

OdB

Speaker Mode

(Front R)

Speaker Mode

(Subwoofer)

‘Not found(No illustration visible)’.

Setting up DELAY TIME

•When 5.1CH Surround Sound is played, you can enjoy the best sound if the distance between you and each speaker is the same. You can set Delay Time in the Center/Surround Speaker to customize the sound to the acoustic of your room.

3	STILL MODE	AUTO
4	SCREEN MESSAGES	ON
5	FRONT DISPLAY	AUTO
6	BLACK LEVEL	OFF
TV ASPECT : Depending on the type of television you have,

Speaker Mode	Channel
(Surround L)	Balance
	(Surround L)
	OdB

Delay Time

(Surround L/R)

Oms

Channel

Balance

(Surround R)

OdB

Speaker Mode

(Surround R)

Ideal CENTER SPEAKER position

• Arrange all

speakers

within circle.

• Setting CENTER SPEAKER

If the distance of Dc is equal to or longer than the distance of Df in the left figure, set the mode as Oms. Otherwise, change the setting according to the table below.

	you may want to adjust the screen setting
	(aspect ratio).
2,3,4	ANGLE MARK : Use to turn on or off the angle mark ( )
	when the DVD plays multiple angles of a
	particular scene.
	STILL MODE : Prevent picture shaking in still mode and dis-
	play small text clearer.
	SCREEN MESSAGES : Use to turn on-screen messages

SPEAKER MODE

You can set a mode in the system that’s currently used. Initially it is set as follows:

• Front speaker (L/R) : Found (Large illustration)

• Center speaker : Not found (No illustration visible)

• Subwoofer : Not found (No illustration visible)

Ideal SURROUND SPEAKER position

(A) = Df - Dc

Distance of (A)(in) Setting(ms)

1.641

3.282

4.923

6.565

on or off.

FRONT DISPLAY

Adjust the brightness of the unit’s front panel display.

BLACK LEVEL

• Surround speaker (L/R) : Not found (No illustration visible)

DELAY TIME

You can customize the sound to conform to the acoustics of your room by adding a delay effect to the sound of the Center and Surround Speakers. Initially it is set as “Oms (millise- conds)”.

TEST

Test signals memorized in the system are sent to each speaker.

CHANNEL BALANCE

Adjust the output level of a speaker by using test signals that are memorized in the system. Initially it is set as “OdB”.

How to make the SETUP MENU disappear or

return to menu screen during set up.

Press RETURN button.

• Setting SURROUND SPEAKERS

If the distance of Df is equal to the distance of Ds in the above, set the mode as Oms. Otherwise, change the setting

according to the table on the right.	(B) = Df - Ds
	Distance of (B)(in)	Setting(ms)
	6.56	5
	13.12	10
	19.68	15

Setting up TEST

The test output signals come clockwise starting from the Front Speaker(L). Adjust Channel Balance to match to the volume of test signals memorized in the system.

FRONT(L) CENTER FRONT(R)

SUBWOOFER SURROUND(R) SURROUND(L)

N• The subwoofer test output signal is lower than the other

Ospeakers.

T• The MPEG Multichannel logo is a trademark registered by

EPHILIPS Corporation.

4.Use the UP/DOWN button to select the desired item. Then press the ENTER button.					CHANGING SETUP MENU
	TV ASPECT			FIELD : Select this feature when the screen shakes in the
			1
		4:3 LETTER BOX :		AUTO mode.
	1
		Select when you want to see the total 16:9 ratio screen DVD		FRAME : Select this feature when you want to see small let-
			2
		supplies, even though you have a TV with a 4:3 ratio screen.		ters more clearly in the AUTO mode.
		Black bars will appear at the top and bottom of the screen.	3	AUTO : When selecting AUTO, FIELD/FRAME mode will be
		4:3 PAN-SCAN :		automatically converted.
	2
		Select this for conventional size TVs when you want to see	SCREEN MESSAGES
		the central portion of the 16:9 screen. (Extreme left and right
				Use this feature to turn the on-screen displays on or off that
		side of movie picture will be cut off.)
				appear in screen.
		16:9 WIDE :
	3
			FRONT DISPLAY
		You can view the full 16:9 picture in your widescreen TV.
				BRIGHT : It makes the Front Panel Display bright.
	ANGLE MARK		1
				DIM : It makes the Front Panel Display dim.
			2
	1	ON : Displays ANGLE MARK in the upper right corner of
				AUTO DIM : It makes the Front Panel Display dim automati-
			3
		screen.
				cally when playing a DVD.
		OFF : Doesn’t display it.
	2
			BLACK LEVEL
	STILL MODE
			Adjust the brightness of screen.

36 37