Samsung CL-29Z40MQ manual Changing Channels, Using the Channel Buttons, Using the Number Buttons

Page 31

O P E R AT I O N

Changing Channels

Using the Channel Buttons

Press the CH or CH button to change channels.

When you press CH or CH , the TV changes channels in sequence. You will see all the channels that the TV has memorized. (The TV must have memorized at least three channels.) You will not see channels that were either erased or not memorized.

Using the Number Buttons

Use the number buttons to quickly tune to any channel.

Press the number buttons to go directly to a channel.

For example, to select channel 27, press “2” then “7”.

The TV will change channels when you press the second number.

To select a channel over 100, press the “-” button. (For channel “122”, press the +100 button, then “2”, then “2”.)

Using the “-” Button in DTV mode

The “-” button is used to select channels that broadcast a digital signal.

For example, for channel 7 (digital), press “7”, then “-”, then “1” and you will see as left.

DTV 7 - 1 TV #1

English

Using the PRE-CH Button to Select the Previous Channel

Alternate method:

Press the PRE-CHbutton. The TV changes to the last channel you were watching.

œTo quickly switch between two channels that are far apart, tune to one channel, then use the number buttons to select the second channel. Then, use the PRE-CHbutton to quickly alternate between them.

English - 31

Image 31

Contents

Owner’s Instructions English Guide to Digital TV Digital Television ServicesIntegrated TVs versus DTV-ready TVs and monitors How to View Digital TelevisionHow difficult is it to receive DTV signals indoors? Your New TV InstallationOperation Troubleshooting Special FeaturesAppendix Checking Accessories List of FeaturesFamiliarizing Yourself with the TV Audio R/L Input Connection Jacks SideVideo Input ´ Video Input´ Video Input jacks Audio-Video Output jacks Upgrade Port USBConnection Jacks Rear Antenna terminalsMenu Remote Control´ Number buttons ¨ VOL +, VOLAntennas with 300-ohm Flat Twin Leads Connecting VHF and UHF AntennasSeparate VHF and UHF Antennas Antennas with 75-ohm Round LeadsConnecting to a Cable Box that Descrambles All Channels Connecting Cable TVCable without a Cable Box This terminal might be labelled ANT IN, VHF in or simply, Connecting to a Cable Box that Descrambles Some ChannelsVCR Rear Panel Connecting a VCRThey are usually found on the side or rear Camcorder Connecting a CamcorderConnecting a Second VCR to Record from the TV Locate the A/V output jacks on the CamcorderConnecting to Y, PB, PR Connecting a DVD PlayerConnecting to Regular Audio and Video Jacks AV OUT R-AUDIO-L Connecting to an Analog AmplifierInstalling Batteries in the Remote Control Turning the TV On and Off Plug & Play FeatureFirst analog, then digital channels will be memorized Press the … or † button to select the desired connectionPress the Enter button Start Plug & Play is displayed Refer to Setting the Clock onViewing the Display Press the Info button on the remote controlViewing the Menus and On-Screen Displays Viewing the MenusSelecting the Antenna Input Selecting a Menu LanguagePress the Menu button Memorizing the Channels Selecting the Video Signal SourceStoring Channels in Memory When selection Cable TVStart Adding and Erasing Channels Using the PRE-CH Button to Select the Previous Channel Using the Channel ButtonsUsing the Number Buttons Using the Button in DTV modeWhich will be selected Labelling the ChannelsPicture Control Using Automatic Picture SettingsPress the Enter button again Customizing the Picture Resetting the Picture Settings to the Factory Defaults + or VOL button Adjusting the VolumeUsing the Mute Button Sound ControlUsing Automatic Sound Settings Press the Enter button AdjustedCustomizing the Sound Press the … or † buttonClock Setting the ClockSetting the Signal Source Viewing an External Signal SourcePress the Enter button Press the Exit button to exit Assigning Names to External Input ModeAnalog Fine Tuning ChannelsDigital Checking the Digital-Signal StrengthDTV Mode TV ModeChanging the Screen Size Digital Noise Reduction Press the … or † button to select Tilt TiltSurf Off is displayed Using the R.Surf FeatureChoosing a Multi-Channel Sound MTS track English Auto Volume Set the Off Timer as methods for On Timer setting Setting the On/Off TimerOn Timer Channel Setting the Preferred OptionSetting the Sleep Timer Press the Enter button to select Caption Viewing Closed Captions On-Screen Text MessageCaption Off Digital Captions function operates on digital channels Size Setting the Blue Screen Mode Setting the On/Off Melody Chapter Five Identifying ProblemsUsing Your TV in Another Country Cleaning and Maintaining Your TVSpecifications This page is intentionally Left blank This page is intentionally Left blank Country Customer Care Center Web Site Contact Samsung WORLD-WIDE