Memorizing the Channels
Your TV can memorize and store all of the available channels for both 
or CH 
button to scan through the channels.
This eliminates the need to change channels by entering the channel digits. There are three steps for memorizing channels: selecting a broadcast source, memorizing the channels (automatic) and adding and deleting channels (manual).
Selecting the Video Signal-source
Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i.e. an air or a cable system).
Channel
Antenna |
| : Air |
| ˆ | |
Auto Program |
|
|
|
| ˆ |
Channel Manager |
|
|
| ˆ | |
Name |
|
|
|
| ˆ |
Fine Tune |
|
|
|
| ˆ |
Signal Strength |
|
|
| ˆ | |
Move | Enter | Return | |||
|
|
|
| ||
|
|
|
|
|
|
Channel |
|
| |||
Antenna |
| : |
|
|
|
| AirAir |
|
| ||
Auto Program |
|
| Cable |
|
|
Channel Manager |
|
|
|
| |
Name |
|
|
|
|
|
Fine Tune |
|
|
|
|
|
Signal Strength |
|
|
|
| |
1.Press the MENU button to display the menu.
Press the or button to select “Channel”, then press the ENTER button.
2.Press the ENTER button select “Antenna”.
Press the or button to select “Air” or “Cable”, then press the ENTER button.
Press the EXIT button to exit.
Move 
Enter 
Return
Storing Channels in Memory (Automatic Method)
|
|
| 1. | Press the MENU button to display the menu. |
| Channel |
| ||
Antenna | : Air | ˆ |
| Press the or button to select “Channel”, then press the ENTER button. |
Auto Program | ˆ | 2. | Press the or button to select “Auto Program”, then press the ENTER | |
Channel Manager | ˆ | |||
Name |
| ˆ |
| button. |
Fine Tune |
| ˆ |
|
|
Signal Strength | ˆ |
|
| |
Move | Enter | Return |
|
|
Auto Program
Select the antennas to memorize.
Air |
| Start |
Cable |
| Start |
Air + Cable |
| Start |
Move | Enter | Return |
3.Press the or button to select the antenna connection, then press the ENTER button.
➢Air: “Air” antenna signal.
Cable: “Cable” antenna signal.
Air+Cable: “Air” and “Cable” antenna signals.
➢If the antenna is connected to ANT 1 IN (AIR), select “Air” and if it is connected to ANT 2 IN (CABLE), select “Cable”.
➢If both ANT 1 IN and ANT 2 IN are connected, select the “Air + Cable”.
➢If you selected “Air”, then go to step 5.
Auto Program
Select the cable system.
Analog
STD | ✔ | Start |
HRC |
|
|
IRC |
|
|
4.Select the correct signal source (STD, HRC, and IRC) by pressing the ˇ button, then press the or button.
Press the ˆ button to select “Start”, then press the ENTER button.
➢STD, HRC, and IRC identify various types of cable TV systems. Contact your local cable company to identify the type of cable system that exists in your particular area. At this point the signal source has been selected.
Move 
Enter 
Return
Auto Program
Auto Program in progress.
Air 16
15%
Stop
Enter 
Return
5.After all the available channels are stored, the “Auto Program” menu reappears. Press the EXIT button to exit.
You can also press the AUTO PROG. button on the remote control to bring up the Auto Program menu.