Samsung TX-T2781, TX-T2782, TX-T2082 manual Upgrading the Software, Identifying Problems

Page 23

Upgrading the Software

Samsung may offer upgrades for your TV’s firmware in the future. Please contact the Samsung call center at 1-800-SAMSUNG to receive information about downloading upgrades and using a USB drive. Upgrades will be possible by connecting a USB drive to the USB port located on the back of your TV.

1Insert a USB drive containing the firmware upgrade into the USB Upgrade Port on the back of the TV.

2Press the MENU button to display the menu.

Press the ▲ or ▼ button to select Setup, then press the ENTER button.

3Press the ▲ or ▼ button to select Software upgrade, then press the ENTER button.

4 Press the ▲ or ▼ button to select USB Upgrade, then press the ENTER button. The message Scanning for USB... It may take up to 30 seconds. is displayed.

Please be careful to not disconnect the power or remove the USB drive while upgrades are being applied.

The TV will shut off and turn on automatically after completing the firmware upgrade. Please check the firmware version after the upgrades are complete.

The firmware and upgrade process may be different by country and region.

USB Drive

 

Software upgrade

USB Upgrade

Move Enter Return

USB Upgrade

Scanning for USB...

It may take up to 30 seconds.

Identifying Problems

If the TV seems to have a problem, first try this list of possible problems and solutions.

If none of these troubleshooting tips apply, call your nearest Samsung service center.

Problem

Possible Solution

Poor picture quality.

Try another channel.

 

Adjust the antenna.

 

Check all wire connections.

Poor sound quality.

Try another channel.

 

Adjust the antenna.

No picture or sound.

Try another channel.

 

Press the SOURCE button.

 

Make sure the TV is plugged in.

 

Check the antenna connections.

 

Make sure the MUTE button is off.

No sound or sound is too low at

First, check the volume of units connected to your TV (digital broadcasting receiver, DVD,

maximum volume.

cable broadcasting receiver, VCR, etc.). Then, adjust the TV volume accordingly.

Picture rolls vertically.

Check all connections.

The TV operates erratically.

Unplug the TV for 30 seconds, then try operating it again.

The TV won’t turn on.

Make sure the wall outlet is working.

Remote control malfunctions

Replace the remote control batteries.

 

Clean the upper edge of the remote control(transmission window).

 

Check the battery terminals.

 

Press the TV/DTV button to put your remote control in the “TV” mode.

 

Make sure the remote has batteries.

 

Check that the “+” and “-” ends of the batteries are inserted correctly.

Digital broadcasting screen problem.

Please check the digital signal strength and input antenna.

 

 

The image is too light or too dark.

Adjust the Brightness and Contrast.

 

Adjust the Fine tuning.

The visual qualities of digital

The visual qualities of digital channels may vary depending on the original production

channels vary.

method(analog or digital).

 

- If the original production method is digital: High visual quality program.

 

- If the original production method is analog: The digital program displayed on the screen is

 

originally an analog program which has been converted to digital. The visual quality is of an

 

SD(Standard Definition) grade.

Although the TV caption shows HD,

The HD(High Definition) caption that appears when switching channels or when pressing the

the visual quality is not satisfactory.

Information button on the remote control means the selected channel is a digital channel. If the

 

broadcasting station converts an analog signal into digital and transmits the signal, the visual

 

quality may not be perfect.

English - 23

Image 23
Contents Owner’s Instructions Contents Viewing the Control Panel AccessoriesHeadphone Viewing the Connection PanelRear of the TV Side of the TV AV in 1 / AVRemote Control Connecting Cable TV Connecting VHF and UHF AntennasVideo Connection Connecting a VCRConnecting a Camcorder Connecting an Amplifier/DVD Home Theater Analog Connecting a DVD Player/Set-Top BoxPress the Enter button, then the Language menu is displayed Plug & Play FeatureWhen selecting Cable TV If you want to reset this featureStoring Channels in Memory Automatic Method Selecting the Video Signal-sourceMemorizing the Channels Dynamic Using Automatic Picture SettingsTo Select the Source To Edit the Input Source NameCool1 Resetting the Picture Settings to the Factory DefaultsChanging the Screen Size Digital Noise ReductionCustomizing the Sound Using Automatic Sound SettingsChoosing a Multi-Channel Sound MTS Track Analog Automatic Volume ControlReduces the differences in volume level among broadcasters Choosing a Multi-Channel Sound MTS Track DigitalAdding and Erasing Channels Analog Using Pseudo StereoUsing Turbo Plus Clearing Scrambled Channels DigitalAir Added Delete Ch.Change Enter Fine Tuning Analog Channels AnalogAdding and Erasing Channels Digital Labeling Channels AnalogSurf Checking the Digital-Signal Strength DigitalUsing the R.Surf Feature Selecting a Menu LanguageAuto Power Off Setting the TimeSetting the Sleep Timer To cancel the set sleep timerDigital Captions function operates on digital channels Size DefaultViewing Closed CaptionsOn-Screen Text Messages Digital Viewing Closed CaptionsOn-Screen Text Messages AnalogDefault PIN of a new TV set is Setting the Blue Screen ModeSetting the On/Off Melody Using the V-ChipChange PIN Setting Up Your Personal ID NumberPINBlock All Downloadable U.S. RatingHumor Level Allow AllSDStandard Definition grade Identifying ProblemsPlease check the digital signal strength and input antenna Upgrading the SoftwareWeb Site Address SpecificationsContact Samsung WORLD-WIDE Country