Samsung TXM 1967, TXM 1997, TXM 1367 manual Connecting to a Cable Box that Descrambles All Channels

Page 16

I N S TA L L AT I O N

Connecting to a Cable Box that Descrambles All Channels

1

Find the cable that is con- nected to the ANTENNA OUT terminal on your cable box.

2

Connect the other end of this cable to the VHF/UHF antenna terminal on the back of the TV.

This terminal might be labeled “ANT OUT,” “VHF OUT,” or simply, “OUT.”

Connecting to a Cable Box that Descrambles Some Channels

If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will need a two-way splitter, an RF (A/B) switch, and four lengths of coaxial cable. (These items are available at most electronics stores.)

1

Find and disconnect the cable that is connected to the ANTENNA IN terminal on your cable box.

This terminal might be labeled “ANT IN,” “VHF IN,” or simply, “IN.”

2

Connect this cable to a two-way splitter.

3

Connect a coaxial cable between an OUTPUT ter- minal on the splitter and the IN terminal on the cable box.

2.3 CHAPTER TWO: INSTALLATION

Image 16

Contents Owner’s Riskofelectricshock Donotopen Thank You for Choosing Samsung With §15.119 of the FCC rules Read these instructions Your New TV InstallationOperation Special Features TroubleshootingList of Features Chapter OneFamiliarizing Yourself with The TV Rear Panel Jacks Video and Audio input jacks ´ VHF/UHF Antenna terminalRemote Control Type Number buttons¨ +100 Sleep´ Number buttons Erase+100 ∏ REWRewindSET ˘ FF Fast ForwardPress to use your remote con- trol to operate your VCR Press to use your remote con- trol to operate a cable boxConnecting VHF and UHF Antennas Antennas with 300-ohm Flat Twin LeadsConnecting Cable TV Antennas with 75-ohm Round LeadsSeparate VHF and UHF Antennas Cable without a Cable BoxConnecting to a Cable Box that Descrambles Some Channels Connecting to a Cable Box that Descrambles All ChannelsConnect this cable to a two-way splitter S TA L L AT I O N Connecting a VCR Connect an audio cable to the VCR’s Audio OUT terminalS TA L L AT I O N Connecting a Camcorder Installing Batteries in the Remote Control Press the Power button on the remote control Turning the TV On and OffViewing the Menus and On-Screen Displays Viewing the MenusSelecting a Menu Language Memorizing the Channels Selecting the Video Signal-sourceANT antenna STD, HRC or IRC all cable TV Storing Channels in Memory Automatic Method Press the CH button to select Auto programAdding and Erasing Channels Manual Method Press the VOL+ or VOL- button to select Added or ErasedAdjusting the Volume Changing ChannelsSetting the Clock Or CH button repeat- edly until the correct hour appearsCustomizing the Picture Press the Menu button to display the menuUsing Automatic Picture Settings Auto Volume Press the VOL+ or VOL- button Viewing a VCR or Camcorder TapePress the Menu button twice to exit Customizing Your Remote Control Setting Up Your Remote Control to Operate Your VCRVCR Codes Setting Up Your Remote Control to Operate Your Cable Box Cable Box CodesFine Tuning Channels Changing the Screen Size Using the Surf Feature Setting the On/Off Timer Setting the Sleep Timer Press the Sleep button on the remote controlViewing Closed Captions Setting Up Your Personal ID Number PIN Using the V-ChipPress the Menu button three times to exit How to Enable/Disable the V-Chip How to Set up Restrictions Using the TV guidelinesTV-Y Young children TV-Y7 Children 7 and over General audienceParental guidance TV-14E C I a L FE AT U R E S Repeatedly press the CH Button to select a General audience no restrictionsIdentifying Problems Chapter FiveUsing Your TV in Another Country Cleaning and Maintaining Your TVSpecifications