Samsung TXM 1997, TXM 1967, TXM 1367 Memorizing the Channels, Selecting the Video Signal-source

Page 24

O P E R AT I O N

Memorizing the Channels

Your TV can memorize and store all of the available channels for both “off-air” (antenna) and cable channels. After the available channels are memorized, use the CH ▲ and CH ▼ buttons to scan through the channels. This eliminates the need to change chan- nels by entering the channel digits. There are three steps for memorizing channels: selecting a broadcast source, memorizing the channels (automatic) and adding and deleting channels (manual).

Selecting the Video Signal-source

Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i.e., an antenna or a cable system).

1

Press MENU to display the menu.

Press CH ▼ two times to select “Channel”, then press the VOL + button.

2

Repeatedly press VOL + to cycle through these choices:

ANT (antenna)

STD, HRC or IRC (all cable TV).

Note: STD, HRC and IRC identify various types of cable TV systems. Contact your local cable company to identify the type of cable system that exists in your particular area.

At this point the signal source has been selected. Proceed to “Storing Channels in Memory” (next page).

3

Press MENU twice to exit.

3.3 CHAPTER THREE: TV OPERATION

Image 24

Contents Owner’s Riskofelectricshock Donotopen Thank You for Choosing Samsung With §15.119 of the FCC rules Read these instructions Installation Your New TVOperation Special Features TroubleshootingList of Features Chapter OneFamiliarizing Yourself with The TV Rear Panel Jacks Video and Audio input jacks ´ VHF/UHF Antenna terminalRemote Control Type Number buttons¨ +100 Sleep´ Number buttons Erase+100 ∏ REWRewindSET ˘ FF Fast ForwardPress to use your remote con- trol to operate your VCR Press to use your remote con- trol to operate a cable boxConnecting VHF and UHF Antennas Antennas with 300-ohm Flat Twin LeadsConnecting Cable TV Antennas with 75-ohm Round LeadsSeparate VHF and UHF Antennas Cable without a Cable BoxConnecting to a Cable Box that Descrambles All Channels Connecting to a Cable Box that Descrambles Some ChannelsConnect this cable to a two-way splitter S TA L L AT I O N Connecting a VCR Connect an audio cable to the VCR’s Audio OUT terminalS TA L L AT I O N Connecting a Camcorder Installing Batteries in the Remote Control Press the Power button on the remote control Turning the TV On and OffViewing the Menus and On-Screen Displays Viewing the MenusSelecting a Menu Language Selecting the Video Signal-source Memorizing the ChannelsANT antenna STD, HRC or IRC all cable TV Storing Channels in Memory Automatic Method Press the CH button to select Auto programAdding and Erasing Channels Manual Method Press the VOL+ or VOL- button to select Added or ErasedAdjusting the Volume Changing ChannelsSetting the Clock Or CH button repeat- edly until the correct hour appearsCustomizing the Picture Press the Menu button to display the menuUsing Automatic Picture Settings Auto Volume Viewing a VCR or Camcorder Tape Press the VOL+ or VOL- buttonPress the Menu button twice to exit Customizing Your Remote Control Setting Up Your Remote Control to Operate Your VCRVCR Codes Setting Up Your Remote Control to Operate Your Cable Box Cable Box CodesFine Tuning Channels Changing the Screen Size Using the Surf Feature Setting the On/Off Timer Setting the Sleep Timer Press the Sleep button on the remote controlViewing Closed Captions Using the V-Chip Setting Up Your Personal ID Number PINPress the Menu button three times to exit How to Enable/Disable the V-Chip How to Set up Restrictions Using the TV guidelinesTV-Y Young children TV-Y7 Children 7 and over General audienceParental guidance TV-14E C I a L FE AT U R E S Repeatedly press the CH Button to select a General audience no restrictionsIdentifying Problems Chapter FiveCleaning and Maintaining Your TV Using Your TV in Another CountrySpecifications