Listening through a Receiver (Home theater)
You can listen to sound through a receiver instead of the TV speaker.
1.Press the TOOLS button. Press the ENTER 
button to select “Anynet+
2.Press the ▲ or ▼ button to select “Receiver”. Press the ◄ or ► button to select “On” or “Off”.
3.Press the EXIT button to exit.
➣If your receiver supports audio only, it may not appear in the device list.
➣The receiver will work when you have properly connected the Optical IN jack of the receiver to the Optical Out jack of the TV.
|
|
|
|
View TV |
|
|
|
Device List |
|
|
|
Recording | : | DVDR |
|
DVDR Operation |
|
|
|
Receiver | ◄ | On | ► |
Setup |
|
|
|
|
|
|
|
| UMove | LAdjust | RReturn |
➣When the receiver (home theater) is set to On, you can hear sound output from the TV’s Optical jack. When the TV is displaying a DTV(air) signal, the TV will send out 5.1 channel sound to the Home theater receiver. When the source is a digital component such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from the Home Theater receiver.
➣When using the WISELINK feature, sound may not output properly through the receiver.
➣When listening through the receiver, there are restrictions for using the PIP and
➣If there is a power interruption to the TV when the “Receiver” is set to “On” (by disconnecting the power cord or a power failure), the “Select Speaker” may be set to “External Speaker” when you turn the TV on again. (see page 34)
Troubleshooting for Anynet+
Symptom | Solution |
|
|
Anynet+ does not work. | • Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ |
| devices only. |
| • Connect only one receiver (home theater). |
| • Check if the Anynet+ device power cord is properly connected. |
| • Check the Anynet+ device’s Video/Audio/HDMI 1.3 cable connections. |
| • Check whether Anynet+ |
| • Check whether the TV remote control is in TV mode. |
| • Check whether it is Anynet+ exclusive remote control. |
| • Anynet+ doesn’t work in certain situations. (Searching channels, Operating |
| WISELINK, Plug & Play, etc.) |
| • When connecting or removing the HDMI 1.3 cable, please make sure to search |
| devices again or turn your TV off and on again. |
| • Check if the Anynet+ Function of Anynet+ device is set on. |
|
|
I want to start Anynet+. | • Check if the Anynet+ device is properly connected to the TV and check if the |
| Anynet+ |
| • Press the TV/DTV button on the TV remote control to switch to TV. Then press |
| the TOOLS button to show the Anynet+ menu and select a menu you want. |
I want to exit Anynet+. | • Select View TV in the Anynet+ menu. |
| • Press the SOURCE button on the TV remote control and select a device other |
| than Anynet+ devices. |
| • Press P / and |
| (Note that the channel button operates only when a |
| device is not connected.) |
The message Connecting to | • You cannot use the remote control when you are configuring Anynet+ or |
Anynet+ device... appears on the | switching to a view mode. |
screen. | • Use the remote control when the Anynet+ setting or switching to view mode is |
| complete. |
The Anynet+ device does not play. | You cannot use the play function when Plug & Play is in progress. |
The connected device is not | • Check whether or not the device supports Anynet+ functions. |
displayed. | • Check whether or not the HDMI 1.3 cable is properly connected. |
| • Check whether Anynet+ |
| • Search Anynet+ devices again. |
| • You can connect an Anynet+ device using the HDMI 1.3 cable only. Some HDMI |
| cables may not support Anynet+ functions. |
| • If it is terminated by an abnormal situation such as disconnecting the HDMI cable |
| or power cord or a power failure, please repeat the device scan. |
The TV program cannot be | Check whether the antenna jack on the recording device is properly connected. |
recorded. |
|
The TV sound is not output | Connect the optical cable between TV and the receiver. |
through the receiver. |
|
English - 72