Samsung UN55C5000 user manual Network Setup Samsung Auto Configuration, Boot up

Page 28

Advanced Features

Notice

The picture may appear corrupted or have static for some channels when the TV is connected to the Samsung Wireless LAN Adapter. In such a case, establish a connection using one of the following methods or connect the Samsung Wireless LAN Adapter using a USB cable in a place that is not affected by radio interference.

Method 1

Method 2

Connect using the USB right angle adapter

Connect via an extension cable

or

To connect the Samsung Wireless LAN Adapter using the USB right angle adapter, follow these steps:

1.Connect the USB right angle adapter to the Samsung Wireless LAN Adapter.

2.Connect the other end of the right angle adapter to the USB 1 (HDD) port.

To reconnect the Samsung Wireless LAN Adapter using the extension cable, follow these steps:

✎✎ The Samsung Wireless LAN Adapter should be installed in an interference-free area in order to avoid interference between the adapter and tuner.

1.Connect the extension cable to the USB 1 (HDD) port.

2.Connect the extension cable and Samsung Wireless LAN Adapter.

3.Attach the Samsung Wireless LAN Adapter to the back of the TV near the top, using double-sided adhesive tape.

Network Setup (Samsung Auto Configuration)

The Samsung Auto Configuration function lets you connect your Samsung TV automatically to non-Samsung wireless APs. If your non-Samsung AP does not support Samsung Auto Configuraton, you must connect using one of the other methods: PBC (WPS), auto configuration, or manual configuration.

✎✎To use this function, you must set

SWL (Samsung Wireless Link) to Off in the TV’s on- screen menu.

✎✎You can check for equipment that supports Samsung Auto Configuration on www.samsung.com.

How to set up using Samsung Auto Configuration

1.Place the AP and TV next to each other and turn them

on.

✎✎ Because AP booting times vary, you may have to wait approximately two minutes for your AP to

boot up.

✎✎ Ensure the LAN cable is connected to the WAN port of the AP during Samsung Auto Configuration. If it is not connected, Samsung Auto Configuration only confirms that the TV is connected to the AP, but does not confirm it is connected to the Internet.

28 English

2.After 2 minutes, connect the Samsung Wireless LAN Adapter to the TV. When the Samsung Wireless LAN Adapter establishes a connection with your TV, a pop-up window appears.

3.As soon as a connection is established, place the AP parallel to the Samsung Wireless LAN Adapter and not farther than than 9 and 7/8s inches (25cm) from it.

4.Wait until the connection is automatically established. ✎✎ If Samsung Auto Configuration does not connect

your TV to your AP, a pop-up window appears on the screen notifying you of the failure. If you want to try using Samsung Auto Configuration again, reset the AP, disconnect the Samsung Wireless LAN Adapter and then try again from Step 1. You can also choose one of the other connection setup methods: PBC (WPS), auto, or manual.

5.Place the AP in a desired location.

✎✎ If the AP settings change or you install a new AP, you must perform the Samsung Auto Configuration procedure again, beginning from Step 1.

[UC5000(55)_USA]BN68-03004A-01Eng.indb 28

2010-06-28 오후 1:06:46

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Samsung Electronics Canada Inc., Customer Service Samsung Electronics America, Inc ChallengerSecuring the Installation Space Installation with a standInstallation with a wall-mount Still image warningContents List of Features AccessoriesCleaning Cloth BN63-01798B Component Composite AV Coaxial RFInstall the Stand See separate guide for installing the standStand 1EA Follow the steps below to connect the TV to the standButtons on the remote control Speakers Remote control sensorViewing the Control Panel Product color and shape may vary depending on the modelViewing the Remote Control StartedConnecting to an Antenna Plug & Play Initial SetupPower Input VHF/UHF AntennaConnecting to an AV Device ConnectionsConnecting to an Audio Device Digital Audio OUT OpticalConnecting to a PC Using an HDMI/DVI Cable or a D-sub CableMode Resolution Horizontal Frequency Vertical Frequency Sync PolarityHow to Navigate Menus Source ListEdit Name Changing the Input SourceChannel List Add to Favorite / Delete from FavoriteAntenna Air / Cable t Auto ProgramOther Features Clear Scrambled ChannelProgrammed Editing ChannelsMode t Eco SolutionAdvanced Settings Fine TunePicture Options Picture OptionsOff Turns the Expert Pattern function off OO MENUm→ Picture → Picture Options →Picture Reset OK / Cancel Auto Adjustment tSetting up the TV with Your PC ScreenAuto Volume Off / Normal / Night SRS TruSurround HD Off / On tSRS TruDialog Off / On SRS TheaterSound tSound Reset OK / Cancel Speaker Select External Speaker / TV SpeakerSpdif Output TimeTimer To be played when the TV is turned on automatically. NoteOO MENUm → Setup → Security → Entere SecurityMenu Language CaptionGeneral PIP t Legal NoticeSelf Diagnosis Picture In Picture PIPSoftware Upgrade Software UpgradeHD Connection Guide Contact SamsungConnecting to a Wired Network Network ConnectionModem Port on the Wall LAN Port on the WallNetwork Setup Auto Network Setup ManualNetwork Setup Network Type Wired Network Setup Network TestConnecting to a Wireless Network Network Setup Samsung Auto Configuration Boot upNetwork Setup PBC WPS How to set up automaticallyThen press the ENTEREbutton. Press the or Displays a list of the available networksNetwork Setup Ad-Hoc SWL connect SWL Samsung Wireless LinkTo connect Connecting a USB Device Connecting to your PC through a networkMedia Play USB Mass Storage Class MSC deviceUC500055USABN68-03004A-01Eng.indb 2010-06-28 오후 Videos Screen DisplayBut you cannot play the Game itself Yy Supported Subtitle FormatsAdvanced Features English Yy Supported Video FormatsMusic List section using the Green button PhotosPlaying Multiple Files Media Play Additional FunctionsSettings Same file name as the video AudioWhat is Anynet+? t Advanced To connect to a Sam sung Home Theater FeaturesAnynet+ Home Theater Anynet+Switching between Anynet+ Devices Setting Up Anynet+Recording Troubleshooting for Anynet+ Listening through a ReceiverSetup Setting Up AllShareMessage / Media / ScreenShare About AllShareMy Mobile Other Information Assembling the CablesInstalling the Wall Mount Blanking BracketAnti-theft Kensington Lock Securing the TV to the Wall TV-Holder Kit Sold SeparatelyTV-Holder BN96-15753A Screw M8 x L19Troubleshooting Issues Solutions and ExplanationsOn, refer to ‘Remote control does not work’ below There is no signalMake sure your connected devices are powered on Make sure the Network Connection is set to Wireless pDegree connectors Caption must be activated on the external device pEvery time the TV is turned off Check the cable connections and reconnect themLicense Specifications Front view / Side view DimensionsUnit inches Index Favorite Channel Film Mode Fine Tune Flesh Tone FrequencyAllShare Amplify Antenna Anynet+
Top Page Image Contents