Samsung Official Guide for LED Television Setup and Features

LED TV

user manual

Getting Started

Accessories

• Remote Control (AA59-00600A) &		•	Owner’s Instructions
	Batteries (AAA x 2)
		•	Power Cord
• Warranty Card / Safety Guide
Input Cables (Sold Separately)
•	RS232 (AA39-00311A)	•	Component
•	Audio	•	Composite (AV)
•	HDMI	•	Coaxial (RF)

•HDMI-DVI

✎Check the cable before plug-in

CablePorts

✎When selecting the function by moving the controller to the up/down/left/ right directions, be sure not to press the controller. If you press it first, you cannot operate it to move the up/down/left/right directions.

Plug & Play (Initial Setup)

When you turn the TV on for the fi rst time, a sequence of on-screen prompts will assist in confi guring basic settings. Press the POWER button. Plug & Play is available only when the Input source is set to TV.

✎Connecting the power cord and antenna. (refer to ‘Connections’)

Selecting a language

	Plug & Play		Select the desired OSD (On Screen
Select Language of the OSD.			Display) language.
		English
Language		Español

Connections

y For better picture and audio quality, connect to a digital device using an HDMI cable.			y	PC(D-Sub) and PC/DVI AUDIO IN input are not supported.
y The picture may not display normally (if at all) or the audio may not work if an external			y	For HDMI/DVI cable connection, you must use the HDMI IN 1(DVI) jack.
device that uses an older version of HDMI mode is connected to the TV. If such a problem			y	Connecting through the HDMI cable may not be supported depending on the PC.
occurs, ask the manufacturer of the external device about the HDMI version and, if out of
date, request an upgrade.			y	If an HDMI to DVI cable is connected to the HDMI IN 1(DVI) port, the audio does not work.
y Be sure to purchase a certifi ed HDMI cable. Otherwise, the picture may not display or a			y	EX-LINK: Connector for service only.
connection error may occur.
	AV Device (1)
Using a HDMI Cable (up to 1080p)				y The side panel may differ depending on the model.
HDMI OUT
		TV Side Panel		Power Input
Blu-ray player / DVD / cable box /

Remote Control

✎This remote control has Braille points on the Power, Channel, and Volume buttons and can be used by visually impaired persons.

	Displays and selects the available video
	sources.
Turns the TV on and off.	Turns the remote control light on or off. When
	on, the buttons become illuminated for a
	moment when pressed. (Using the remote
	control with this button set to On will reduce
Press to directly access to channels.	the battery usage time.)
Press to select additional channels (digital) being	Returns to the previous channel.
broadcasted by the same station. For example,
to select channel ‘54-3’, press ‘54’, then press	Cuts off the sound temporarily.
‘-’ and ‘3’.

Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance. Product design and specifi cations may be changed without notice.

Important Warranty Information Regarding

Television Format Viewing

✎See the warranty card for more information on warranty terms.

Wide screen format LED Displays (16:9, the aspect ratio of the screen width to height) are primarily designed to view wide screen format full-motion video. The images displayed on them should primarily be in the wide screen 16:9 ratio format, or expanded to fi ll the screen if your model offers this feature and the images are constantly moving. Displaying stationary graphics and images on screen, such as the dark sidebars on non- expanded standard format television video and programming, should be limited to no more than 5% of the total television viewing per week. Additionally, viewing other stationary images and text such as stock market reports, video game displays, station logos, web sites or computer graphics and patterns, should be limited as described above for all televisions. Displaying stationary images that exceed the above guidelines can cause uneven aging of LED Displays that leave subtle, but permanent burned-in ghost images in the LED picture. To avoid this, vary the programming and images, and primarily display full screen moving images, not stationary patterns or dark bars. On LED models that offer picture sizing features, use these controls to view different formats as a full screen picture. Be careful in the selection and duration of television formats you use for viewing. Uneven LED aging as a result of format selection and use, as well as burned-in images, are not covered by your Samsung limited warranty.

Still image warning

Avoid displaying still images (such as jpeg picture fi les) or still image elements (such as TV channel logos, panorama or 4:3 image format, stock or news bars at screen bottom etc.) on the screen. Constant displaying of still pictures can cause ghosting of LED screen, which will affect image quality. To reduce risk of this effect, please follow below recommendations:

•Avoid displaying the same TV channel for long periods.

•Always try to display any image on full screen, use TV set picture format menu for best possible match.

•Reduce brightness and contrast values to minimum required to achieve desired picture quality, exceeded values may speed up the burnout process.

•Frequently use all TV features designed to reduce image retention and screen burnout, refer to proper user manual section for details.

Securing the Installation Space

Keep the required distances between the product and other objects (e.g. walls) to ensure proper ventilation.

Failing to do so may result in fi re or a problem with the product due to an increase in the internal temperature of the product.

✎ When using a stand or wall-mount, use parts provided by Samsung

Electronics only.

x If you use parts provided by another manufacturer, it may result in a

problem with the product or an injury due to the product falling.

✎ The appearance may differ depending on the product.

HDMI

USB

Optical

Do not plug cable upside down.

Be sure to check before plug-in.

TV Controller (Panel Key)

Function menu

MEDIA.P

m R

P

Return

TV Controller

	Français
	U Move	E Enter
		
			
	Selecting a Home Use mode
				•	Select the Home Use mode. Store
Plug & Play
Select ‘Home Use’ when installing this TV in your home.					Demo mode is for retail environments.
				•	When pressing TV controller, the
		
					function menu screen appears. Select
Store Demo	Home Use				the MENU(m) and press it more than 5
					seconds using the controller. The Store
	L Move	E Enter			Demo mode is set. Cancel the Store
					Demo by selecting Source List(s)
					and pressing it more than 5 seconds.
	Selecting an antenna
Plug & Play				In Cable mode, you can select the correct
Select the Antenna source to memorize.				signal source among STD, HRC, and IRC
				by pressing the ▲, ▼, ◄ or ► button.
Air		Start
Cable		Start

sat box

DVI OUT

TV Rear Panel

Audio Device (1)

HDMI OUT

Using an Audio (Analog) Cable

R

AUDIO IN

PC

W

R-AUDIO-L

DVD / Home Theater

PC

Using a HDMI (to DVI) Cable

VHF/UHF Antenna

or

Media Play

R

W

YR

R

W

R

B

GR

ANT OUT

Using a USB Drive

Cable

R

W

Y

R

W

R

B

RG

Adjusts the volume.			Changes channels.
Displays the channel list on the screen.			Displays the main on-screen menu.
Views the Media Play.	MEDIA.P	SLEEP	Automatically shuts off the TV at a preset
Quickly select frequently used functions.			time.
			Displays information on the TV screen.

Selects the on-screen menu items and changes the values seen on the menu.

Returns to the previous menu. Exit the menu.

	Use these buttons according to the
P.SIZE: Lets you choose the picture size.	direction on screen.
MTS: Press to choose stereo, mono or Separate Audio	Use these buttons in a specifi c feature.
Program (SAP broadcast).

CC: Controls the caption decoder.

• SAMSUNG ELECTRONICS NORTH AMERICAN LIMITED WARRANTY STATEMENT

Subject to the requirements, conditions, exclusions and limitations of the original

Limited Warranty supplied with Samsung Electronics (SAMSUNG) products, and the

requirements, conditions, exclusions and limitations contained herein, SAMSUNG

will additionally provide Warranty Repair Service in the United States on SAMSUNG

products purchased in Canada, and in Canada on SAMSUNG products purchased

in the United States, for the warranty period originally specifi ed, and to the Original

Purchaser only.

The above described warranty repairs must be performed by a SAMSUNG Authorized

Service Center. Along with this Statement, the Original Limited Warranty Statement

✎ Be careful when you contact the TV because some parts can be somewhat

hot.

Installation with a stand.			Installation with a wall-mount.
4inches	4inches		4inches	4inches
		4inches			4inches

Auto		Start
		
		
U Move	E Enter	mSkip
		
	Setting the Clock Mode
Plug & Play			Set the Clock Mode automatically or

AV Device (2)	AV Device (3)
Using an Audio/Video	Using a Component Cable					Audio Device (2)
	(up to 1080p)
					Using an Optical (Digital) Cable
AUDIO OUT VIDEO OUT	AUDIO OUT	COMPONENT OUT			OPTICAL
R-AUDIO-L	R-AUDIO-L
		PR	PB	Y		Digital Audio System

Display Modes (HDMI/DVI Input)

Optimal resolution

4000 series:1366 x 768@60Hz / 5000 series: 1920 x 1080@60Hz

Installing batteries (Battery size: AAA)

and a dated Bill of Sale as Proof of Purchase must be presented to the Service

Center. Transportation to and from the Service Center is the responsibility of the

purchaser. Conditions covered are limited only to manufacturing defects in material or

workmanship, and only those encountered in normal use of the product. Excluded, but

not limited to, are any originally specifi ed provisions for, in-home or on-site services,

minimum or maximum repair times, exchanges or replacements, accessories, options,

upgrades, or consumables.

For the location of a SAMSUNG Authorized Service Center, please call toll-free:

–– In the United States : 1-800-SAMSUNG (1-800-726-7864)

–– In Canada : 1-800-SAMSUNG

4inches

Contact SAMSUNG WORLDWIDE

If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.

Country	CANADA	U.S.A
	Samsung Electronics	Samsung Electronics
	Canada Inc., Customer
Address		America, Inc. 85
	Service 55 Standish Court
		Challenger Road
	Mississauga, Ontario L5R
		Ridgefi eld Park, NJ 07660
	4B2 Canada
Customer Care	1-800-SAMSUNG (726-7864)
Center 
	www.samsung.com/ca
Web Site	(English)	www.samsung.com/us
	www.samsung.com/ca_fr
	(French)

Power on

Adjusting the volume

Selecting a channel

Using the function menu

Selecting the Media Play

Selecting the MENU (m)

Selecting the Source List (s)

Power Off (P)

Remote control sensor

Turns the TV on by pressing the controller in standby mode.

Adjusts the volume by moving the controller from side to side when the power is on.

Selects a channel by moving the controller up and down when the power is on.

Press the controller when the power is on, then the function menu screen appears. If you press it again, the function menu screen disappears.

Selects the MEDIA.P by moving the controller in the function menu screen. The Media Play main screen appears.

Selects the MENU(m) by moving the controller in the function menu screen. The OSD(On Screen Display) of your TV’s feature appears.

Selects the Source List(s) by moving the controller in the function menu screen. The Source List screen appears.

Selects the Power Off (P) to turn the TV off by moving the controller in the function menu screen.

Set the Clock Mode.			manually.
			•	If you select the Auto, set the
	
				DST(Daylight Saving Time).
Clock Mode		: Auto
			•	On the DST screen, press ENTERE,

then select whether to turn DST

(Daylight Savings Time) on or off. Select

E Enter m Skip the time zone where you live.



Viewing the HD Connection Guide

The connection method for the best HD screen quality is displayed.



Enjoy your TV.

Press the ENTEREbutton.

VCR	Blu-ray player
		■ VCR / DVD / Cable STB / Satellite STB / PVR STB / AV
Changing the Input Source
		Receiver / Game / Camcorder / PC / DVI PC / DVI / TV / IPTV
		/ Blu-ray / HD DVD / DMA: Name the device connected to the
Source List		input jacks to make your input source selection easier.
		✎ When connecting a PC to the HDMI IN 1(DVI) port with HDMI
Use to select TV or an external input source such as a DVD player /
Blu-ray player / cable box / STB satellite receiver.		cable, you should set the TV to PC mode under Edit Name.
		✎ When connecting a PC to the HDMI IN 1(DVI) port with HDMI
1. Press the SOURCE button.
		to DVI cable, you should set the TV to DVI PC mode under Edit
2. Select a desired external input source.		Name.
		✎ When connecting an AV devices to the HDMI IN 1(DVI) port
■ TV / AV / Component / HDMI1/DVI / HDMI2
		with HDMI to DVI cable, you should set the TV to DVI mode
✎ You can only choose external devices that are connected to the
		under Edit Name.
TV. In the Source List, connected inputs will be highlighted.
		Information
How to use Edit Name		You can see detailed information about the connected external
Edit Name lets you associate a device name to an input source. To		device.
access Edit Name, press the TOOLS button in Source List. The
following selections appear under Edit Name:

		Horizontal	Vertical	Pixel Clock	Sync
Mode	Resolution			Frequency	Polarity	1366 x 768	1920 x 1080
		Frequency (KHz)	Frequency (Hz)
				(MHz)	(H / V)
IBM	640 x 350	31.469	70.086	25.175	+/-	c	c
	720 x 400	31.469	70.087	28.322	-/+	c	c
	640 x 480	35.000	66.667	30.240	-/-	c	c
MAC	832 x 624	49.726	74.551	57.284	-/-	c	c
	1152 x 870	68.681	75.062	100.000	-/-		c
	640 x 480	31.469	59.940	25.175	-/-	c	c
	640 x 480	37.861	72.809	31.500	-/-	c	c
	640 x 480	37.500	75.000	31.500	-/-	c	c
	800 x 600	37.879	60.317	40.000	+/+	c	c
	800 x 600	48.077	72.188	50.000	+/+	c	c
	800 x 600	46.875	75.000	49.500	+/+	c	c
	1024 x 768	48.363	60.004	65.000	-/-	c	c
	1024 x 768	56.476	70.069	75.000	-/-	c	c
	1024 x 768	60.023	75.029	78.750	+/+	c	c
VESA DMT	1152 x 864	67.500	75.000	108.000	+/+		c
	1280 x 720	45.000	60.000	74.250	+/+	c	c
	1280 x 800	49.702	59.810	83.500	-/+		c
	1280 x 1024	63.981	60.020	108.000	+/+		c
	1280 x 1024	79.976	75.025	135.000	+/+		c
	1366 x 768	47.712	59.790	85.500	+/+	c	c
	1440 x 900	55.935	59.887	106.500	-/+		c
	1600 x 900RB	60.000	60.000	108.000	+/+		c
	1680 x 1050	65.290	59.954	146.250	-/+		c
	1920 x 1080	67.500	60.000	148.500	+/+		c

✎NOTE

xUse the remote control within 23 feet from TV.

xBright light may affect the performance of the remote control. Avoid use when nearby fluorescent lights or neon signs.

xThe Color and shape may vary depending on the model.

BN68-04499B-01 © 2012 Samsung Electronics Co., Ltd. All rights reserved.

- 1 -

✎ Exits the menu when pressing the controller more than 1 second.

- 2 -

- 3 -

- 4 -

Channel Menu

❑Seeing Channels

Channel List

Add, delete or set Favorite channels and use the program guide for digital broadcasts. Select a channel in the All Channels, Added Channels, Favorite or Programmed screen by pressing the ▲

/▼ buttons, and pressing the ENTERE button. Then you can watch the selected channel.

	6	Air
Added	6-1	♥ TV #6
	7-1	♥ TV #7
Channels
	9	Air
	8	Air
	9-1	♥ TV #9
	10	Air
	10-1	♥ TV #10
	11-1	♥ TV #11
Air	' Zoom	' Select TTools ► Next Program

■ All Channels: Shows all currently available channels.

■ Added Channels: Shows all added channels.

■* Favorite: Shows all favorite channels.

■ Programmed: Shows all currently reserved programs.

✎Using the remote control buttons with the Channel List

xGreen (Zoom): Enlarges or shrinks a channel number.

xYellow (Select): Selects multiple channel lists. Select desired channels and press the Yellow button to set all the selected channels at the same time. The c mark appears to the left of the selected channels.

xT (Tools): Displays the Channel List option menu. (The Options menus may differ depending on the situation.)

How to Stop Auto Programming

1.Press the ENTERE button.

2.A message will ask Stop Auto Program? Select Yes by pressing the ◄ or ► button.

3.Press the ENTERE button.

❑Other Features

Clear Scrambled Channel

This function fi lters out scrambled channels after Auto Program is completed. This process may take up to 20~30 minutes.

✎Press the ENTERE button to stop the Clear Scrambled Channel.

✎This function is only available in Cable mode.

Channel List

Channel List Option Menu t

Set each channel using the Channel List menu options. Option menu items may differ depending on the channel status.

■ Add / Delete: Delete or add a channel to display the channels

you want.

✎ All deleted channels will be shown on the All Channels

menu.

✎ A gray-colored channel indicates the channel has been

deleted.

✎ The Add menu only appears for deleted channels.

✎ Delete a channel from the Added Channels or Favorite

menu in the same manner.

■ Add to Favorite / Delete from Favorite t: Set channels

you watch frequently as Favorites.

■ Timer Viewing: You can set a desired channel to be displayed

Channel Mode	Picture Options
Change the channel mode directly between Added Channels and	✎ When connecting a PC, you can only make changes to the
Favorite Channels.	Color Tone, Size and HDMI Black Level.
✎ The Favorite Channels is enabled only when you set Add to	■ Color Tone (Cool / Standard / Warm1 / Warm2)
Favorite.	✎ Warm1 or Warm2 will be deactivated when the picture mode
Fine Tune	is Dynamic.
	■ Size: Your cable box/satellite receiver may have its own set of
(analog channels only)	screen sizes as well. However, we highly recommend you use 16:9
If the reception is clear, you do not have to fi ne tune the channel, as	mode most of the time.
	16:9: Sets the picture to 16:9 wide mode.
this is done automatically during the search and store operation. If the
signal is weak or distorted, fi ne tune the channel manually.	Zoom1: Use for moderate magnifi cation.
✎ Fine tuned channels that have been saved are marked with an	Zoom2: Use for a stronger magnifi cation.
asterisk “*” on the right-hand side of the channel number in the	Wide Fit: Enlarges the aspect ratio of the picture to fi t the entire
channel banner.	screen.
✎ To reset the fine-tuning, select Reset.	4:3: Sets the picture to basic (4:3) mode.
	✎ Do not watch in 4:3 format for a long time. Traces of borders
	displayed on the left, right and center of the screen may
Picture Menu
	cause image retention (screen burn) which are not covered
Mode t	by the warranty.
	Screen Fit (DTV): Displays the full image without any cut-off when
Select your preferred picture type.	HDMI (720p / 1080i / 1080p) or Component (1080i / 1080p)
	signals are inputted.
✎ When connecting a PC, you can only select Entertain and
	✎ HD (High Definition): 16:9 - 1080i/1080p (1920x1080), 720p
Standard.	(1280x720)
■ Dynamic: Suitable for a bright room.	✎ Settings can be adjusted and stored for each external device
■ Standard: Suitable for a normal environment.	you have connected to an input on the TV.
■ Movie: Suitable for watching movies in a dark room.	✎ Picture Sizes available by Input Source:
■ Entertain: Suitable for watching movies and games.	Input Source	Picture Size
✎ Only available when connecting a PC.
Backlight / Contrast / Brightness / Sharpness /	ATV, AV, Component (480i, 480p)	16:9, Zoom1, Zoom2, 4:3
	DTV(1080i, 1080p), Component
Color / Tint (G/R)
	(1080i, 1080p), HDMI (720p, 1080i,	16:9, Wide Fit, 4:3, Screen Fit
Your television has several setting options for picture quality control.	1080p)

	■ Audio Delay: Lets you correct timing mismatches between the
Sound Menu
		audio track and the video when you are watching the TV and
		listening to digital audio output from the TV through an external
Mode t		device such as an AV receiver. When you select Audio Delay, a
		slider appears. Use the left and right arrow buttons to adjust the
■ Standard: Selects the normal sound mode.
		slider. Press ENTERE when done (0ms ~ 250ms).
■ Music: Emphasizes music over voices.	Speaker Select
■ Movie: Provides the best sound for movies.
■ Clear Voice: Emphasizes voices over other sounds.	■ Speaker Select (External Speaker / TV Speaker): If you are
■ Amplify: Increase the intensity of high-frequency sounds to allow a		listening to the sound track of a broadcast or movie through an
better listening experience for the hearing impaired.		external receiver, you may hear a sound echo caused by the
Equalizer		difference in decoding speed between the TV’s speakers and the
		speakers attached to your audio receiver. If this occurs, set the TV
(standard sound mode only)		to External Speaker.
		✎ When you set Speaker Select to External Speaker, the
■ Balance L/R: Adjusts the balance between the right and left
		TV’s speakers are turned off. You will hear sound through the
speaker.		external speakers only. When you set Speaker Select to TV
■ 100Hz / 300Hz / 1KHz / 3KHz / 10KHz (Bandwidth Adjustment):		Speaker both the TV’s speakers and the external speakers
Adjusts the level of specifi c bandwidth frequencies.		are on. You will hear sound through both.
■ Reset: Resets the equalizer to its default settings.		✎ When Speaker Select is set to External Speaker, the
SRS TruSurround HD		VOLUME and MUTE buttons will not operate and the sound
		settings will be limited.
(standard sound mode only)		✎ If there is no video signal, both the TV’s speakers and the
SRS TruSurround HD is a patented SRS technology that solves the		external speakers will be mute.
problem of playing 5.1 multichannel content over two speakers.	Sound Reset
TruSurround delivers a compelling, virtual surround sound experience
through any two-speaker playback system, including internal	■ Reset All: Resets all sound settings to the factory defaults.
television speakers. It is fully compatible with all multichannel formats.
Preferred Language		Setup Menu
(digital channels only)
Digital-TV broadcasts are capable of simultaneous transmission of	❑ Setting the Time
many audio tracks (for example, simultaneous translations of the
program into foreign languages).	Time
✎ You can only select a language from among the ones being

■Contents: When the On Time is activated, you can turn on a specifi c channel or play back contents such as photo or audio fi les.

-TV/USB: Select TV or USB. (Make sure that an USB device is connected to your TV.)

-Antenna: Displays the current antenna source.

-Channel: Select the desired channel.

-Music/Photo: Select the folder containing MP3/JPEG fi les on the USB device.

✎The maximum displayed number of files, including sub folders, in one folder of USB storage device is 2000.

✎The media may not be playing smoothly when using the device lower than USB 2.0.

■Repeat: Select Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun or Manual to set at you convenience. If you select Manual, you can set up the day you want to activate the timer.

❑Other Features

Program Rating Lock

The Program Rating Lock feature automatically locks out programs that are deemed inappropriate for children. The user must enter a PIN (personal identifi cation number) before any of the Program Rating Lock restrictions are set up or changed.

✎ Program Rating Lock is not available in HDMI or

Component mode.

✎ The default PIN number of a new TV set is “0-0-0-0”.

■ Program Rating Lock: You can block rated TV Programs.

■ TV Parental Guidelines: You can block TV programs

depending on their rating. This function allows you to control

what your children are watching.

■ MPAA Rating: You can block movies depending on their MPAA

rating. The Motion Picture Association of America(MPAA) has

implemented a rating system that provides parents or guardians

✎Game Mode is not available when the input source is set to TV.

✎After connecting the game console, set Game Mode to On. Unfortunately, you may notice reduced picture quality.

Caption

(On-Screen Text Messages)

■ Caption: You can switch the caption function on or off. If

captions are not available, they will not be displayed on the

screen.

✎ The Caption feature does not work in Component or

HDMI mode.

■ Caption Mode: You can select the desired caption mode.

Default / CC1~CC4 / Text1~Text4: (analog channels only) The

Analog Caption function operates in either analog TV channel

mode or when a signal is supplied from an external device to

the TV. (Depending on the broadcasting signal, the Analog

Caption function may or may not work with digital channels.)

Default / Service1~Service6 / CC1~CC4 / Text1~Text4:

(digital channels only) The Digital Captions function works with

digital channels.

✎ Service1~6 may not be available in digital caption mode

depending on the broadcast.

■ Digital Caption Options: (digital channels only)

Size: Options include Default, Small, Standard and Large. The

default is Standard.

Font Style: Options include Default and Styles 0 to 7. The

default is Style 0.

Foreground Color: Options include Default, White, Black, Red,

Green, Blue, Yellow, Magenta and Cyan.

You can change the color of the letter. The default is White.

Background Color: Options include Default, White, Black, Red,

Green, Blue, Yellow, Magenta and Cyan. You can change the

background color of the caption. The default is Black.

Channel Status Display icons

IconsOperations

c A channel selected.

* A channel set as a Favorite.

)	A reserved program.
(	A program currently being broadcast.

❑Memorizing channels

Antenna (Air / Cable) t

Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i.e. an Air or a Cable system).

Auto Program

✎When selecting the Cable TV system: Selects the cable system. STD, HRC and IRC identify various types of cable TV systems. Contact your local cable company to identify the type of cable system that exists in your particular area. At this point, the signal source has been selected.

✎After all the available channels are stored, it starts to remove scrambled channels. The Auto program menu then reappears.

✎Press the ENTERE button to stop the channel store during

Auto Program.

automatically at the set time; even when you are watching

another channel. Set the current time fi rst to use this function.

✎ Only memorized channels can be reserved.

✎ Reserved programs will be displayed in the Programmed

menu.

✎ When a digital channel is selected, press the ► (Next

Program) button to view the digital program. If you select

the ENTERE(Schedule) button on the next program, you

can set Timer Viewing directly.

■ Channel Name Edit (analog channels only): Assign your own

channel name.

■ Select All: Select all the channels in the channel list.

■ Deselect All: Deselect all the selected channels.

✎ You can only select Deselect All when one or more

channels are selected.

■ Auto Program: Scans for a channel automatically and stores in

the TV

Programmed

(in Channel List)

You can view, modify or delete a show you have reserved to watch.

■Change Info: Change a show you have reserved to watch.

■Cancel Schedules: Cancel a show you have reserved to watch.

■Information: Display a show you have reserved to watch. (You can also change the reservation Information.)

■Select All / Deselect All: You can select or deselect all channels in the channel list.

✎When connecting a PC, you can only make changes to Backlight, Contrast, Brightness and Sharpness

Advanced Settings

(available in Standard / Movie mode)

Compared to previous models, new Samsung TVs have a more precise picture.

✎When connecting a PC, you can only make changes to Gamma and White Balance.

■Color Space (Auto / Native): Adjusts the range of colors available to create the image.

■White Balance: Adjusts the color temperature for a more natural picture.

R-Offset / G-Offset / B-Offset: Adjusts each color’s (red, green, blue) darkness.

R-Gain / G-Gain / B-Gain: Adjusts each color’s (red, green, blue) brightness.

Reset: Resets the White Balance to it’s default settings.

■Gamma: Adjusts the primary color intensity.

■Dynamic Contrast (Off / Low / Medium / High): Adjusts the screen contrast.

■Black Tone (Off / Dark / Darker / Darkest): Select the black level to adjust the screen depth.

■Flesh Tone: Emphasize pink “fl esh tone”.

■Motion Lighting (Off / On): Reduce power consumption by brightness control adapted motion.

✎ Available in Standard mode only.

■Digital Noise Filter (Off / Low / Medium / High / Auto): If the broadcast signal received by your TV is weak, you can activate the Digital Noise Filter feature to reduce any static and ghosting that may appear on the screen.

✎When the signal is weak, try other options until the best picture is displayed.

■HDMI Black Level (Normal / Low): Selects the black level on the screen to adjust the screen depth.

✎Available only in HDMI mode (RGB signals).

■Film Mode (Off / Auto): Sets the TV to automatically sense and process fi lm signals from all sources and adjusts the picture for optimum quality.

✎Available in ATV, DTV(interlace), AV, COMPONENT (480i / 1080i) and HDMI (480i / 1080i).

■LED Motion Plus (Off / On): Removes drag from fast scenes with a lot of movement to provide a clear picture.

Picture Reset

Resets your current picture mode to its default settings.

■Reset Picture Mode: Returns all picture values in the currently selected mode to the default settings.

broadcasted.	✎ The current time will appear every time you press the INFO
Multi-Track Sound (MTS)	button.
	■ Clock: Setting the clock is for using various timer features of the
(analog channels only)	TV.
■ Mono: Choose for channels that are broadcasting in mono or if	✎ If you disconnect the power cord, you have to set the clock
	again.
you are having diffi culty receiving a stereo signal.
	Clock Mode: Set the current time manually or automatically.
■ Stereo: Choose for channels that are broadcasting in stereo.
■ SAP: Choose to listen to the Separate Audio Program, which is	Clock Set: Set the Month, Day, Year, Hour, Minute and am/pm.
usually a foreign-language translation.	✎ Available only when Clock Mode is set to Manual.
✎ Depending on the program being broadcast, you can listen to	Time Zone: Select your time zone.
Mono, Stereo or SAP.	DST (Daylight Saving Time): Switches the DST (Daylight Saving
Auto Volume	Time) function on or off.
	✎ DST and Time Zone function is only available when the
Because each broadcasting station has its own signal conditions,	Clock Mode is set to Auto.
the volume may fl uctuate each time channel is changed. This feature	■ Sleep Timer t
lets you automatically adjust the volume of the desired channel by	Automatically shuts off the TV after a preset period of time. (30,
lowering the sound output when the modulation signal is high or by
	60, 90, 120, 150 and 180 minutes).
raising the sound output when the modulation signal is low.
	✎ To cancel the Sleep Timer, select Off.
SPDIF Output
	Timer 1 / Timer 2 / Timer 3
The SPDIF (Sony Philips Digital InterFace) outputs an uncompressed
digital audio signal when you connect the digital audio jack on the	Three different on / off timer settings can be made. You must set the
back of the TV to a digital audio in jack on a receiver or home theater.	clock fi rst.
■ Audio Format: You can select the Digital Audio output (SPDIF)	■ On Time / Off Time: Set the hour, minute, am/pm and Activate /
format. The available Digital Audio output (SPDIF) format may differ	Inactivate. (To activate the timer with the setting you have chosen,
depending on the input source.	set to Activate.)
✎ By connecting the TV to a receiver or home theater with Dolby	■ Volume: Set the desired volume level.

Digital and 5.1ch speakers and selecting Dolby Digital, you can maximize your interactive 3D sound experience.

with advanced information on which fi lms are appropriate for

children.

■ Canadian English: You can block TV programs depending on

their Anglophone Canadian.

■ Canadian French: You can block TV programs depending on

their French Canadian rating.

■ Downloadable U.S. Rating: Parental restriction information can

be used while watching DTV channels.

■ Change PIN: The Change PIN screen will appear. Choose any

4 digits for your PIN and enter it in Enter New PIN. Re-enter

the same 4 digits in Confi rm New PIN. When the Change

PIN screen disappears, press the OK button. The TV has

memorized your new PIN.

✎ If you forget the PIN, press the remote-control buttons in

the following sequence, which resets the pin to “0-0-0-0” :

POWER (off) → MUTE → 8 → 2 → 4 → POWER (on)

Language

Set the menu language.

✎Choose between English, Español and Français.

Game Mode

When connecting to a game console such as PlayStation™ or Xbox™, you can enjoy a more realistic gaming experience by selecting the game menu.

✎Precautions and limitations for game mode

xTo disconnect the game console and connect another external device, set Game Mode to Off in the setup menu.

xIf you display the TV menu in Game Mode, the screen shakes slightly.

Foreground Opacity: This adjusts the opacity of text. Options

include Default, Transparent, Translucent, Solid and Flashing.

Background Opacity: This adjusts the opacity of the caption

background. Options include Default, Transparent, Translucent,

Solid and Flashing.

Return to Default: This option sets each Size, Font Style,

Foreground Color, Background Color, Foreground Opacity and

Background Opacity to its default.

✎ Digital Caption Options are available only when Default

and Service1 ~ Service6 can be selected in Caption

Mode.

✎ The Foreground and Background cannot be set to have

the same color.

Melody

Set so that a melody plays when the TV is turned on or off.

✎The Melody does not play.

xWhen no sound is output from the TV because the MUTE button has been pressed.

xWhen no sound is output from the TV because the volume has been reduced to minimum with the VOL – button.

xWhen the TV is turned off by Sleep Timer function.

Auto Protection Time

■Auto Protection Time (Off / 2 hours / 4 hours / 8 hours / 10 hours): If the screen remains idle with a still image for a certain period of time defi ned by the user, the screen saver is activated to prevent the formation of ghost images on the screen.

- 5 -

- 6 -

- 7 -

- 8 -