Samsung LTM 225W manual Chapter Four, Setting Up Your Remote Control

Page 37

08.CHAPTER4_EN 2/5/03 12:34 AM Page 1

Chapter Four

S P E C I A L F E AT U R E S

Setting Up Your Remote Control

After it has been set up properly, your remote control can operate in four different modes: TV, VCR, Cable, or DVD. Pressing the corresponding button on the remote control allows you to switch between these modes, and control whichever piece of equipment you choose.

Note

The remote control might not be compatible with all DVD Players, VCRs and Cable boxes.

Setting Up the Remote to Operate Your VCR

1 Turn off your VCR.

2 Press the MODE button and make sure that the VCR LED

is illuminated.

3 Press the Set button on your TV’s remote control.

4 Using the number buttons on your remote control, enter

three digits of the VCR code listed on page 4.4 of this manual for your brand of VCR. Make sure you enter three digits of the code, even if the first digit is a “0”.

(If more than one code is listed, try the first one.)

5 Press the Power button on the remote control. Your VCR

should turn on if your remote is set up correctly.

If your VCR does not turn on after set up, repeat steps 2, 3, and 4, but try one of the other codes listed for your brand of VCR. If no other codes are listed, try each VCR code, 000 through 089.

Note on Using Remote Control Modes: VCR

When your remote control is in “VCR” mode, the volume buttons still control your TV’s volume.

CHAPTER FOUR: SPECIAL FEATURES 4.1

Image 37

Contents Owner’s Instructions Inside Front Coveren 2/4/03 1144 PM Thank You for Choosing Samsung Prefaceen 2/4/03 1144 PM Prefaceen 2/4/03 1144 PM FCC Information Your New TV InstallationOperation Troubleshooting Special FeaturesPC Display List of Parts List of FeaturesFamiliarizing Yourself with The TV VIDEO/AUDIO in jack Rear Panel JacksSuper Video in jack Headphone jackFrequently Used Buttons Remote ControlVOL +, VOL Number buttonsConvenient Buttons +100 Menu adjustment and Video or DVD adjustment buttonPIP controls Multichannel Television StereoAntennas with 300-ohm Flat Twin Leads Connecting VHF and UHF AntennasAntennas with 75-ohm Round Leads Connecting Cable TVSeparate VHF and UHF Antennas Cable without a Cable BoxConnecting to a Cable Box that Descrambles Some Channels Connecting to a Cable Box that Descrambles All ChannelsS TA L L AT I O N Connecting a VCR Connecting an S-VHS VCR Connecting a Digital TV Set-Top Box Connecting a DVD PlayerSUB Connecting a PCInstalling Batteries in the Remote Control Connecting to a Sub-wooferTurning the TV On and Off Plug & Play FeatureIf you want to reset this feature Viewing the Menus Viewing the Menus and On-Screen DisplaysViewing the Display Selecting a Menu Language Memorizing the Channels Selecting the Video Signal-sourceStoring Channels in Memory Automatic Method Directly Accessing Channels Using the Channel ButtonsUsing the Pre-CH Button to select the Previous Channel Changing ChannelsUsing Mute Adjusting the VolumeUP/DOWN Setting the ClockCustomizing the Picture Alternate method Using Automatic Picture SettingsCustomizing the Sound Using Automatic Sound Settings Viewing a VCR or Camcorder Tape Chapter Four Setting Up Your Remote ControlSetting Up the Remote to Operate Your Cable Box Setting Up the Remote to Operate Your DVD Remote Control Codes Fine Tuning Channels LNA Low Noise Amplifier Setting the Blue Screen Mode Freezing the Picture Changing the Screen SizeChoosing a Multi-Channel Sound MTS Soundtrack Special Sound OptionsAuto Volume Virtual Dolby Adjusting the Headphone Sound Selecting the Sound You can select either Main or Sub when PIP is OnSetting the On/Off Timer What is Absent Power Off? LEFT/RIGHT buttons to select Caption or Text Viewing Closed CaptionsViewing Picture-in-Picture PIP SettingsActivating Picture-in-Picture Swapping the Contents of the PIP image and Main image Selecting a Signal Source External A/V for PIPChanging the PIP Channel Changing the Location of the PIP WindowSetting Up Your Personal ID Number PIN Using the V-ChipHow to Set up Restrictions Using the TV guidelines How to Enable/Disable the V-ChipTV-Y E C I a L F E AT U R E S NC-17No children under age Adults only NR Not rated How to Set up Your PC Software Windows only Using Your TV as a Computer PC DisplayAdjusting Coarse Adjusting the Screen QualityChanging the Screen Position Changing the Screen Color Standard Adjusting the Screen Color Settings To Return the Custom settings back to the default positionChapter Six Identifying ProblemsProblem Possible Solution Display Modes Clock Sync Polarity Mode Resolution Frequency KHz MHzRefer to page A.3 to remove the base Installing Vesa compliant mounting devicesAttaching a Wall or Arm mounting device Maintenance of Your LCD TVOptional Using the Anti-Theft Kensington LockUsing Your TV in Another Country Cleaning and Maintaining Your TVPin Assignments LTM225W Specifications