Samsung 460DX, 400DX specifications Self-Test Feature Check, Not Optimum Mode

Page 73

Select Language

Main Page

Safety Instructions

Introduction

Connections

Using the Software

Adjusting the LCD Display

Troubleshooting

Self-Test Feature Check

Check List

Q & A

Specifications

Information

Appendix

Model

The color and appearance of the product may vary depending on the model, and the product specifications are subject to change without prior notice for reasons of performance enhancement.

Troubleshooting

Self-Test Feature Check

Note

Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself.

Self-Test Feature Check

Your LCD Display provides a self test feature that allows you to check whether your LCD Display is functioning properly.

1)Turn off both your computer and the LCD Display.

2)Unplug the video cable from the back of the computer.

3)Turn on the LCD Display.

The figure shown below ("Check Signal Cable") appears on a black background when the LCD Display is working normally even though no video signal is detected: While in the Self-Test mode, the LED power indicator remains green and the figure moves around on the screen.

4)Turn off your LCD Display and reconnect the video cable; then turn on both your computer and the LCD Display

If your LCD Display screen remains blank after using the previous procedure, check your video controller and computer system; your LCD Display is functioning properly.

Not Optimum Mode

You can even view the screen at a resolution of 1360 x 768. However, you will receive the following message for a minute; You can choose to change the screen resolution or stay in the current mode during that time. And if the resolution is more than 85Hz, you will see the black screen because the LCD Display does not support over 85Hz.

Note

Refer to Specifications > Preset Timing Modes for the resolutions or frequencies supported by the LCD Display.

Image 73
Contents Using the Software Safety InstructionsAdjusting the LCD Display TroubleshootingModel PowerNotational Installation Do not drop the LCD Display when moving it Clean Others Do not cover the vents on the LCD Display cabinet Outlet and contact the Service Center If the batteries are swallowed, see a doctor immediately Page Quick Setup Guide Package ContentsSub Cable Semi Stand Remote Control Batteries AAA XWall Mount KIT Speaker Set BNC Cable Your LCD DisplayPower button Adjust buttons Left-Right buttons/ Volume buttonsPower indicator Remote Control SensorDVI / PC in Dvihdcp PC Video Connection Terminal DVI / PC in RGB PC Video Connection TerminalKensington Lock Remote ControlMDC On / OFF+100 VOLEnter MenuAuto 15 CH/PFM Stereo Audio Type MTS/SModeSyncMaster 400DX Monitor Head Speaker Installation Vesa Bracket Wall Bracket Installation To mount the product on the wall bracket Wall Bracket Angle Adjustment SyncMaster 460DX Monitor Head Speaker Installation Vesa Bracket Wall Bracket Installation To mount the product on the wall bracket Wall Bracket Angle Adjustment Installing the Semi Stand Installing the Stand KITConnecting a Computer Connecting the LCD DisplayConnecting a DVD Player Connecting a VCRConnecting a Camcorder Connecting Speakers Connecting a DTV Set Top BoxConnecting to a Wired Remote Control Connecting to an Audio SystemConnecting Using a DVI to Hdmi Cable Connecting HdmiConnecting Using a DVI to Hdmi Cable Main Screen IntroductionPort Selection Power Control Page Input Source PC, BNC, DVI Image SizeImage Size TV, AV, S-Video, Component, Dvihdcp Time PIP Size PIPPIP Source Page Settings Picture Settings Picture PC SRS TS XT Settings AudioMaintenance Lamp Control Settings Image LockMaintenance Scroll Maintenance Video Wall Troubleshooting Settings Value Display In Multiple Display Mode Input Available Modes Direct button on the remote control is the Source buttonSource List BNC DVI Video ComponentPicture PC / BNC /DVI Mode Available Modes Direct button on the remote control is the Swap button SizeTransparency High Medium Low OpaqueOff Cool Normal Warm Custom Available in PC, BNC mode only Direct button on the remote control is the M/B buttonEntertain InternetOff Direct button on the remote control is the Auto buttonCoarse FineSignal Control Signal Balance169 SharpnessOff Cool2 Cool1 Normal Warm1 Warm2 Direct button on the remote control is the P.MODE buttonDynamic Contrast Film ModeDigital NR Digital Noise Reduction Available Modes PIP on SoundOff Direct button on the remote control is the SRS button You can hear the sound even when sound value is set toMusic SpeechSleep Timer Sub Available Modes PIP on SetupOn Timer Off TimerLow Opaque Five adjustment levels 1, 2, 3, 4, VerticalNormal Low Video WallSafety Screen Five adjustment levels 1, 2, 3, 4, Screen DividerOff Interval ~10 Hour SecondColor Reset Image Reset1366 X Normal PivotID Input ID SetupDirect Functions Available Modes Lock OnSelf-Test Feature Check Self-Test Feature CheckNot Optimum Mode Symptoms and Recommended Actions Maintenance and CleaningProblems related to the Installation PC Mode Check ListProblems related to Audio Problems related to the ScreenScreen is blank and it is blinking How can I set the Power Saving function? Remote control buttons do not respondHow can I clean the outer case/LCD Panel? No soundGeneral GeneralPowerSaver PowerSaverPreset Timing Modes Preset Timing ModesHorizontal Frequency SyncMaster 460DX PowerSaver When used as a normal monitor Horizontal Frequency Product Information Image Retention Free For Better DisplayPower Off, Screen Saver, or Power Save Mode Apply the Screen Scroll function on Product Apply the Screen Erasing function on Product Contact Samsung Worldwide AppendixCIS Resolution Terms Sync SignalDot Pitch Vertical FrequencyAuthority
Related manuals
Manual 90 pages 21.16 Kb