Samsung SPK4215M manual Setting up Your Monitor Plug and Play, Installing the Video Driver

Page 23

Setting up Your Monitor Plug and Play

Our adoption of the new VESAPlug and Play solution eliminates complicated and time consuming setup. It allows you to install your monitor in a Plug and Play compatible system without the usual hassles and confusion. Your PC system can easily identify and configure itself for use with your display. This monitor automatically tells the PC system its Extended Display Identification (EDID) data using Display Data Channel (DDC) protocols so the PC system can automatically configure itself to use the flat panel display. If your PC system needs a video driver, following the instructions given below according to the operating system your computer uses.

Installing the Video Driver

When prompted by the operating system for the monitor driver, insert the Driver diskette included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions as appropriate for the operating system you have.

Windows98, WindowsMe and Windows2000

1.Windows_ 98, Windows_ Me and Windows_ 2000 will auto-detect your new monitor and start the "Add New Hardware Wizard" if the drivers are not already installed. Click the NEXT button to search for drivers.

2.Check the diskette drive box to install the drivers off the diskette provided with your monitor and click NEXT.

3.Confirm that Windows found the driver on the diskette and click NEXT again to install the driver. To manually install or update the driver, follow the directions below:

1.Click on START, SETTINGS, CONTROL PANEL, DISPLAY SETTINGS tab, ADVANCED, MONITOR tab, CHANGE, This will start the "Add New Hardware Wizard".

2.Follow the same directions as given in the steps in the section above.

Version 4.00.950A

1.Click on START, SETTINGS, CONTROL PANEL, DISPLAY SETTINGS tab, CHANGE DISPLAY TYPE,

CHANGE, HAVE DISK.

2.Type the diskette drive letter in the box and click OK.

Version 4.00.950B

1.Click on START, SETTINGS, CONTROL PANEL, DISPLAY, ADVANCED PROPERTIES, MONITOR tab,

HAVE DISK.

2.Type the diskette letter in the box and click OK

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Owner’s Instructions For Commercial USE only Thank You for Choosing Samsung Important Safety InformationPage User Instructions FCC InformationScreen Image retention WarrantyUser Instructions Table of Contents Page Setup Power Button Remote Control Signal ReceiverRGB Input jack 15pin Power Input jack Video Input jackComposite Input jack Remote Control Buttons ¯ Clock set button Remote Control Operation RangeVCR control buttons ˜ Set buttonWall attachment panel Installation NotesInstalling the Display on the Wall Attachment Panel Page Separating the Display from the Wall Attachment Panel Viewing the Menus Turning the MonitorPDP On and OffViewing the Menus and Displays Displaying Clock Indication LightsDisplaying Status Information Page Connecting PC and Operation To watch the PC screen Connecting to a PCVersion 4.00.950A Setting up Your Monitor Plug and PlayInstalling the Video Driver Windows 98, Windows Me and WindowsHow to Set up Your PC Software Windows only IBM PC / AT Adjusting the R.G.B Adjusting the PC ScreenChanging the Position of the Image Changing the Size of the Image Enlarge of the Image Zoom Move Expanded Picture Picture Automatic Adjustment On/Off Picture Quality AdjustmentFrequency Adjustment Fine Tuning Phase Information Power Saver PC mode only Page Connection Videotape Playback Connecting a VCR/Cable BoxTo Watch DTV To Play DVDPage Picture Control Customizing the Picture Using Automatic Picture Settings Selecting the PIP Screen Viewing the Picture-in-PictureSelecting an External Signal Changing the Size of the PIP Image Swapping the Contents of the PIP Image and Main Image Changing the Location of the PIP Image Zoom2 WidePanorama Zoom1Still Freezing the PictureAuto Pixel Shift Time Setting Time Setting the ClockSetting the Sleep Timer Setting the On/Off Timer Setting the TimersOn Time 06 30 Am On Page Function Description Supported Operating Systems Installation ProceduresPDP Remote Controller menu Canceling pins when Pin No. is set to Setting the PinOperating pins when Pin No. is set to Setting up Your Remote Control Remote Control Codes Page Appendix Problem TroubleshootingLiquids Care and MaintenanceIdentifying Problems TemperatureSpecifications Memo AA68-01689AENG
Top Page Image Contents