Samsung PS-42V4S manual Selecting the Sound Mode depending on the model, Forced mono

Page 40

Selecting the Sound Mode (depending on the model)

ENG

The “DUAL I-II” button displays/controls the processing and output of the audio signal. When power is switched on, the mode is automatically preset to either “Dual-I ” or “Stereo”, depending on the current transmission.

		Type of broadcast	On-screen indication

		Regular broadcast	Mono (Normal use)
		(Standard audio)	Mono (Normal use)
		(Standard audio)

		Regular +	NICAM Mono ↔ Mono
	NICAM	NICAM Mono	NICAM Mono ↔ Mono
	NICAM	NICAM Mono
	Stereo	NICAM Stereo	NICAM Stereo ↔ Mono
			NICAM Stereo ↔ Mono
			(Forced mono)
			(Forced mono)

		NICAM Dual-I/II	NICAM Dual-I→
		NICAM Dual-I/II	NICAM Dual-II→
			Mono

		Regular broadcast	Mono
		(Standard audio)	Mono
		(Standard audio)
	A2
	A2	Bilingual or Dual-I/II	Dual-I↔ Dual-II
	Stereo	Bilingual or Dual-I/II	Dual-I↔ Dual-II

		Stereo	Stereo ↔ Mono
		Stereo	(Forced mono)
			(Forced mono)

➣◆ If the receiving conditions deteriorate, listening will be easier if the mode is set to the Mono.

◆If the stereo signal is weak and an automatic switching occurs, then switch to the Mono.

◆When receiving a mono sound in the AV mode, connect to the “AUDIO-L” input connector on the side of the television. If the mono sound comes out only from left speaker, press the Dual I-IIbutton.

40

Image 40

Contents PDP-TELEVISION Screen Image retention Sold Separately Video CableContents Symbols Actual configuration on your PDP may be different Depending on your modelRear Panel For further details about connection, refer to pages 50~54Infrared Remote Control Inserting the Batteries in the Remote Control Stand base will be sold separately depending on modelInstalling the Display on the Wall Attachment Panel Connecting External Devices to the PDP Connecting Speakers Ferrite Cores Connecting to an Aerial or Cable Television Network Connecting a Satellite Receiver or DecoderUsing a Coaxial cable Rear of the PDPSwitching On and Off Placing in Standby ModeTo switch your PDP off, press the I / button again Mains lead is attached to the rear of your PDPBecoming Familiar with the Remote Control Remote control is used mainly toChange channels and adjust the volume Display the on-screen menu systemPlug & Play Feature To start the search, press the Enter buttonIf you want to reset this feature Choosing Your LanguageStoring Channels Automatically SeeStoring ChannelsManually You wish to identifyAuto PAL Secam or Auto NT3.58 NT4.43 PAL60Channel mode Skipping Unwanted Channels Skipping unwanted channelsSorting the Stored Channels Assigning Names to Channels Activating the Child Lock Activating the child lockChanging the Picture Standard Displaying InformationDynamic Standard Movie Custom High Middle Low Custom Adjusting the Picture Settings Custom Options available in DVI Mode ContrastResult The Custom menu is displayed Brightness, SharpnessAdjusting the Picture Settings DVI Mode Press the Menu button to confirm your choiceColour System and Sound System settings are correct Using the Fine TuneIf reception is weak, you can fine tune a channel manually Viewing the Channel Scan Picture Freezing the Current PicturePositioning and Sizing the screen using Zoom Selecting the Picture SizeSelecting the Film Mode DNIeTM Digital Natural Image engineSetting the Melody Sound Setting the Blue ScreenMelody sounds when the television is powered on or off Viewing the Picture In Picture PIP Table of PIP SettingsTV Ext.1 Ext.2 AV S-Video Component DVI Tvpip Using the LNA Low Noise Amplifier Feature Using the Digital NR Digital Noise Reduction FeatureResult The options available are listed Changing the Sound Standard Standard Music Movie Speech CustomAdjusting the Sound Settings Adjusting the Volume AutomaticallySelecting the Internal Mute Setting the TruSurround XTStereo Selecting the Sound Mode depending on the model Forced monoSetting the Sleep Timer Setting and Displaying the Current Time Switching the Television On and Off Automatically Absent Power OffExt.1 Ext.2 AV S-Video Component DVI Viewing an External Signal SourceSatellite STB, AV Receiver, DVD Receiver, Game Redirecting an Input to the External Output Teletext Feature ContentsDisplaying the Teletext Information Press the TTX/MIX button againSelecting Display Options To display PressSelecting a Teletext Input/Output Specification Connecting to the External DevicesRear of the TV Connecting to the S-Video Input Connecting to the DVI Input Connecting to the Component Input Connecting and Using the Home Theater System Connecting the Home Theater SystemScart Connector Ext.1,Ext.2 DVI Input Connector 24PinPower button Check the picture contrast and brightness settingsCheck the volume Normal picture but no sound Check the volumeMemo After Sales Service