Listening through a Receiver
You can listen to sound through a receiver instead of the TV speaker.
1 Press the Anynet+ button.
Press the ▲ or ▼ button to select Receiver, then press the | TV | P 1 |
|
| |
ENTER button. |
| View TV |
|
|
2 Press the ◄ or ► button to select to On, then press the | Select Device | ||
Record |
| ||
ENTER button. |
| ||
Menu on Device | |||
Now you can listen to sound through the receiver. | |||
Device Operation | |||
3 Press the EXIT button to exit. | |||
Receiver | :On | ||
➢ When the receiver is set to On, you can listen to the TV sound | |||
Setup |
| ||
through the | Move | Enter | |
➢ If the receiver is exclusively for a home theater only (supporting | Exit |
| |
audio only), it may not appear in the device list. |
|
|
➢In case of a content with copyright problem, listening through the receiver may not properly operate.
➢When listening through the receiver, there are restrictions for using the PIP and
Check Points before Requesting Service
Symptom | Solution | |
Anynet+ does not work. | ■ Check if the device is an Anynet+ device. The Anynet+ system | |
| supports Anynet+ devices only. | |
| ■ Connect only one receiver. | |
| ■ Check if the Anynet+ device power cord is properly connected. | |
| ■ Check the Anynet+ device’s Video/Audio/HDMI cable connections. | |
| ■ Check whether Anynet+ | |
| setup menu. | |
| ■ Check whether the TV remote control is in TV mode. | |
| ■ Check whether it is Anynet+ exclusive remote control. | |
| ■ Anynet+ doesn’t work at a certain condition. (Searching channels) | |
| ■ When connecting or removing the HDMI cable, please make sure | |
| to search devices again or restart your TV. | |
| ■ Check if the Anynet+ Function of Anynet+ device is set on. | |
I want to start Anynet+. | ■ Check if the Anynet+ device is properly connected to the TV and | |
| check if the Anynet+ | |
| menu. | |
| ■ Press the TV button on the TV remote control to switch to TV. Then | |
| press the Anynet+ button to show the Anynet+ menu and select a | |
| menu you want. | |
I want to exit Anynet+. | ■ Select View TV in Anynet+ menu. | |
| ■ Press the SOURCE button on the TV remote control and select a | |
| device other than Anynet+ devices. | |
| ■ Press any of CH, CH LIST, and | |
| TV mode. (Note that the channel button operates only when a | |
| ||
The Connecting to Anynet+ | ■ You cannot use the remote control when you are configuring | |
device… message appears | Anynet+ or switching to a view mode. | |
on the screen. | ■ Use the remote control when the Anynet+ setting or switching to | |
| view mode is complete. | |
The Anynet+ device does | You cannot use the play function when Plug & Play is in progress. | |
not play. | ||
| ||
The connected device is not | ■ Check whether or not the device supports Anynet+ functions. | |
displayed. | ■ Check whether or not the HDMI cable is properly connected. | |
| ■ Check whether Anynet+ | |
| setup menu. | |
| ■ Search Anynet+ devices again. | |
| ■ You can connect an Anynet+ device using the HDMI cable only. | |
| Some HDMI cables may not support Anynet+ functions. | |
The TV program cannot be | Check whether the antenna jack on the recording device is properly | |
recorded. | connected. |
English - 38