Panasonic Multimedia Projection Display Turning the Power on and OFF, Power on / OFF, Power OFF

Page 23

Power ON / OFF

Turning the Power ON and OFF

Always be sure to follow the procedure given below to turn the projection display power ON and OFF.

•The lamp cooling fan will continue to operate for approximately 1 minute after the power is turned off. At the same time, the POWER indicator will blink Red.

Do not disconnect the power cord from the outlet and do not open the circuit breaker (unless necessary) while the cooling fan is still operating. Do not disconnect the power cord from the power outlet while the power indicator blinks Red.

POWER button/

POWER indicator

Power ON

Press POWER on projection display or remote control to turn power on.

The Power Indicator blinks Green for about 10 seconds and then turns solid Green.

Power OFF

Press POWER on projection display or remote control to turn power off.

Power shuts off after a Black Screen is displayed for a few seconds.

Note:

If POWER is pressed during the Black Screen display, Power is turned back on.

The Power Indicator blinks Red for about 1 minute and then turns solid Red.

Basic Operation

Note:

When the AC Cord is unplugged, the internal cooling fan stops operating. In this case, the lamp will be insufﬁciently cooled and will take a while to turn ON again.

The Power Indicator

LED	ACTION
Red	Power – OFF (Standby mode)
Red blink	Power – OFF (Now cooling)
Green	Power – ON
Green blink	Power – ON (Preparing to light lamp)

Notes:

•If the POWER button is accidentally turned off during use, after power is turned back on, it may take a short period before the lamp automatically comes on.

•After the unit is turned on, maximum picture brightness will be achieved in 5-10 minutes. This is normal.

23

Image 23

Contents USA Multimedia Projection Display Operating InstructionsFor assistance, please call Important Safety Instructions Trademarks Model Number For assistance, please call 1-888-VIEW PTV843-9788Or send e-mail to consumerproducts@panasonic.com Declaration of ConformityTable of Contents Optional External Equipment Before UsingSafety Precaution Receiver LocationObserve the following precautions AccessoriesRemote Control Battery Installation Before UsingLocation of Controls Illuminated Remote ControlLocation of Controls Controls and Terminals on the projection display Rear Side Antenna Connection InstallationConnecting the Antenna / Cable to the RF in Terminal No VCR Cable Connection InstallationConnecting the Antenna / Cable to the RF in Terminal VCR Connects VCRs and other peripheral equipment How to connect the 1, 2, 3 Input TerminalsDisplay Component Signals Y, PB, PR that can be InputSignal data Information menu Mode type No. of dots Vertical frequencyHow to connect the AV Out Terminals NC Not connected Pin No Signal name How to connect the RGB in TerminalsConnecting a PC to RGB Pin No Signal nameAudio cable RGB cable D-SUB 15P Connecting a DTV Decoder to RGBGND How to connect the Digital in TerminalConnecting a DTV Decoder to Digital Digital in Terminal Pin LayoutsComputer RGB/DIGITAL in signals that can be inputSignals DTV Format SignalsWhen setup is complete, the lowest channel picture appears Power on and OFFInitial Setup If using Cable Box, DSS Receiver, or VCRPower OFF Turning the Power on and OFFPower on / OFF Power onSelect Menu desired by Flow Chart of Main menuReturning to the previous screen Flow Chart of Main menuAdjust items Set an item Select an item On the next Tuning channelsAutomatic channel setting Press to exit menu Tuning channelsWhen setup is complete, the lowest channel picture AppearsPress to display the Manual SET screen Manual channel settingPress to select TV or Cable Manual SETPress to add channels to memory To add channelTo delete channel Press to select channelDesired Channel. Or use Number keys Press to Select Desired Volume LevelProjection display operation Operation can be done from the projection displayAuto shut off Using the number keysProjection display operation TV status displayNormal Full True Aspect ControlsJust Normal Zoom Full Normal Zoom FullJust Mode Picture ExplanationNormal will display a 43 picture at its Standard 43 sizeChannel up and down buttons When a channel button is pressed during channel searchVideo Component Card Digital RGB Turning the power on and switching input modesPlaying peripheral equipment Conﬁrming connectionsFreezing pictures Mute / Freeze / SAPSound mute SAP Select Audio Mode for TV ViewingMute / Freeze / SAP Receivable Broadcast TypesPress to return Split screenSplitting the screen Selecting the screen aspect for split screenVideo Split screenChanging the channel of the right screen Swapping left and right screensDisplay PIP screen Picture in Picture PIP ScreenYou can move the PIP screen to four positions Picture in Picture PIP ScreenChanging the channel of the PIP screen Move PIP screenPOSITION/SIZE Adjusting screen position and sizeAdjust Widen Narrow Adjusting screen position and sizePhase Enlarge ShrinkNormal Auto Cinema Music Speech Audio AdjustmentsAudio Treble Audio AdjustmentsUsing BBE BassWarm Picture AdjustmentsPicture DynamicPicture Adjustments Lock Lock FeatureOr Or Enter Secret CodeView NR Not Rated Lock FeatureSetup US Movies Ratings Perform Enter Secret Code onPrograms Setup US TV Programs RatingsPerform US Movies Ratings on US TVRestricted General AudienceParental Guidance Suggested Parents CautionedNo OFF CAP C1 Text C1 CAP C2 Text C2 Caption Mode Text C1 or C2Caption Mode OFF Closed CaptionsNo OFF CAP C1 CAP C2 Closed CaptionsCC on Mute Press repeatedly to selectChannel Caption Channel Caption FeatureDisplay Weak Signal Display FeatureVideo NR Video NR Noise Reduction FeatureVideo Press to display the Video screenAutomatically changing screen size VGA RGB/DIGITAL in Input FeatureRGB DigitalSet to OFF if picture appears 3D Y/C Feature3D IP Feature OFFOFF Sleep Timer FeatureSleep Timer OtherInformation Switching languages for displayInformation English Español FrançaisPress to display the Other screen Demo Mode FeatureDemo Mode Folders and Files Jpeg Viewer SD Card/PC CardCard Data Protection Card Menu Screen Jpeg Viewer SD Card/PC CardInsert the Card Remove the CardReturn Operation Menu Area OperationIndex Area Operation Press Left column of next Single Play ModePress to display next/previous page of 9 thumbnail ﬁles Press Action to display ﬁle in full screen sizeFrom Slide Show ModePicture Adjustment Information Screen DisplayLamp has a maximum life of about 10 000 hours Lamp unit replacement periodReplacing the lamp unit Rcvr VCRCBL DBSCable When code is not knownInfrared Remote Codes for Speciﬁc Components VCR Infrared Codes Index Maker Set Up NoMaker List CBL Maker List Personal Video Recorders Button Quick Reference Functional Button ChartMode Function Button Mode Function Symptoms Checks TroubleshootingPT-50LC13 SpeciﬁcationsCustomer Services Directory CleaningCategory Parts Labor Service Limited WarrantyPanasonic Multimedia Projection Display Limited Warranty Customer’ Record Power button/POWER indicator 10, 23Index Channel up / down buttons projection display

Related manuals

Manual 80 pages 61.19 Kb

Manual 46 pages 37.12 Kb