Samsung SDE5003, SDE-500X, SDE-5003, SDE-400X user manual Overview

Page 4

overview

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.

This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING

To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.

WARNING

1.Be sure to use only the standard adapter that is specified in the specification sheet. Using any other adapter could cause fire, electrical shock, or damage to the product.

2.Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric shock, or damage to the product.

3.Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause abnormal heat generation or fire.

4.Securely plug the power cord into the power receptacle. Insecure connection may cause fire.

5.When installing the camera, fasten it securely and firmly. The fall of camera may cause personal injury.

6.Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled with water on top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects.

7.Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock.

8.If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center. Continued use in such a condition may cause fire or electric shock.

9.If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifications or attempted repair.)

10.When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock.

11.Do not expose the product to the direct airflow from an air conditioner.

Otherwise, it may cause moisture condensation inside the Clear Dome due to temperature difference between internal and external of the dome camera.

12.If you install this product in a low-temp area such as inside a cold store, you must seal up the wiring pipe with silicon, so that the external air can not flow inside the housing.

Otherwise, external high, humid air may flow inside the housing, pooling moisture or vapor inside the product due to a difference between internal and external temperature.

4_ overview

Image 4
Contents Channel Channel DVR SDE-400x/SDE-500xChannel Channel DVR Important Safety Instructions  OverviewOverview Battery Operating TemperatureBefore Start System ShutdownContents Connecting Web Viewer Mac Using Live Viewer MacUsing Live Viewer Windows 120 SEC Backup ViewerFeatures Standards ApprovalsPackage Contents SDE-4001P Package Camera Cable 4EA Quick Start GuideCamera Power Cable 1EA SDE-4003N PackageSDE-4004N Package Mouse 1EA Camera Cable 4EA Quick Start Guide 1EASDE-4005N Package SDE-5001N Package Camera Cable 8EA Quick Start Guide 1EA SDE-5002P/AJ Model doesn’t include Warranty Card SDE-5002N PackageSDE-5003N Package Part Names and Functions Front Mode / Next AlarmREC MenuPart Names and Functions Rear Power CameraVGA USBRemote Control  Console is designed for the service repair purpose onlyUsing the numeric buttons Changing the Remote Control IDChannel Press each button between 1 to 9 CHInstallation Checking the Installation Environment Connecting with Other DeviceConnecting the VIDEO, Audio and Monitor 10 11 8 13 14 15Connecting the USB Connecting the Camera SED-1001R, SEB-1005R, SEB-1007R Connecting with Other Device IR LEDConnecting the Camera SEB-1020R RJ-45 Cable Length 18.3m, 60ftCVBS+ Cvbs GND NameConnecting with DVR Installing the cameraSEB-1005R SEB-1007R Camera Bracket Specification Camera BracketAdjusting the Camera Bracket Installing the camera SED-1001R Precautions before installationMount the main unit onto the bracket Adjusting the monitoring direction for the cameraPanning Tilting Connecting the Alarm INPUT/OUTPUT Connecting the NetworkConnecting to network through Ethernet 10/100BaseT Connecting the alarm Input signalConnecting to Network through Adsl Connecting to the Network using the routerWith Press the Power button again to restart Getting StartedStarting the system Shutting Down the SystemLogin Remote control or the front panel of the DVR whenLocking All Buttons Control or the front panelLive Screen Configuration Icons on the Live ScreenAlarm OUT Error InformationLive Screen Menu Split Mode Menu Single Mode Menu Single mode menu is available only in Single ModeMenu Description Full Screen Zoom Enlarges the selected image. SDE-400X do not support the 16-split screen mode Date/Time/Language Time. Screen ModeAlarm Freeze View the Launcher MenuLive Mode Switching the screen modeSwitching the split mode Auto SequenceManual Switching If pressing the right button in 4-split modeChannel Setting Switching to Single ModeSelecting a Spot Out mode Spot OUTZoom Multichannel Live MenuAudio ON/OFF Audio On/Off in Single modeFreeze Event Monitoring System Setup Setting the Date/Time/LanguageDate/Time/Language  Main MenuDST Set up Daylight Saving Time with its period to make When the Date/Time/Language setup is done, press OKDate Sets the date that will appear on the screen You can select the date formatUsing the Calendar Setting HolidayMain Setting the Administrator Using Virtual KeyboardYou can set and change Administrator’s ID and password Permission ManagementSetting the Group To set the group authorityTo change the user password LoginTo restrict the user permissions UserWhen the user setup is done, press OK Setting the UserAdd User When the permission setup is done, press OK Setting PermissionsUse the virtual keyboard to enter the user ID System Management Checking the System InformationUpdating the Software System Management BroadcastS/W Upgrade Center for assistanceLog Information SettingsSystem Log Backup Log Backup LogEvent Log Select Event Log Use direction buttonsSetting the Device Setting the CameraCamera Press Enter buttonTo set the privacy region When the camera setup is done, press OKPrivacy Region Storage Device Confirming DevicesYou can check information on storage devices Select DeviceFormatting You can format a storage deviceSelect Format FormattedHDD Alarm Remote DevicesSetting Display position Setting the MonitorMonitor Setting the Spot Out Setting the Screen ModeSetting the Recording Recording ScheduleRecord Recording ScheduleEvent Record Duration Recording Color TagsREC Quality & Resolution Setting Standard Recording PropertiesSetting Event Recording Properties When the Event recording setup is done, press OKRecord Option Record OptionAuto Delete Setting the Event Sensor DetectionWindow of motion detection area setup appears Motion DetectionMotion Detection Sensor DetectionSetting the Motion Detection Area Video Loss DetectionAlarm Schedule Alarm ScheduleApply to All Alarm Backup Setting the BackupYou can backup the desired data to a connected device BackupNetwork Configuration Connection ModeSetting the Connection You can set the network connection route and protocolMove to Connection Mode, and press Enter Setting the ProtocolProtocol Network Overview NotificationDVR 1st Set Port Forwarding Setting 2nd Set Port Forwarding SettingConnecting and Setting the Network When no router is usedWhen a router is used Internal Port Range Set the same to the External Port Range Case of Port Forwarding SettingNetwork Main menu When the Ddns setup is done, press OK DdnsIPOLiS Ddns Setting Ddns SettingAfter log in, register your set with your information Live Transfer Live TransferMailing Service Smtp SettingEvent Setting Group SettingButton to move to Mailing Service and press Event Interval Set the event intervalWhen the recipient setting is done, press OK Recipient SettingGroupAdd recipient Time Search Search Search & Play Event Search Zoom In The map enlarges in detailHours  Double-click a desired time to zoom it in/out You can search for events by the channel and play themBackup Search Refer to Type in Backup Setting the Backup.Motion Search PlayPlayback Backup RangePlay Using the Playback Button What is Web Viewer? Product FeaturesIntroducing WEB Viewer System RequirementsSafari on MAC Connecting WEB Viewer MAC WEB Viewer Using Live Viewer MAC Connecting WEB Viewer Windows Using Live Viewer Windows Single Mode Quad Mode Nine Mode Sixteen Mode Single ModeOSD Information Display Split-ScreenChanging The Live Screen Mode Setting the display of the OSD time informationConnected DVR CH5 to CH8 Saving The Live Screen On The PCCapture Saves the current screen into a BMP or Jpeg file Changing The Live Screen Channel Using Search Viewer You can change the split mode by clicking each number icon Number of simultaneous connection is limited toSaving The Live Screen On The PC Check duplicates Searching The Recorded Video In The CalendarSearching The Recorded Video In The Timeline Viewer Setup SystemControlling Playback Date/Time/LanguageHoliday Permission ManagementSystem Management Device CameraStorage Device Remote DeviceMonitor For more information, refer to Setting the Recording. RecordRecording Schedule Event Record DurationREC Quality & Resolution You can set the Disk End ModeEvent Record OptionAlarm Schedule You can set the alarm output time if a video loss occursMotion Detection Video Loss DetectionNetwork For more information, refer to Network Configuration.Connection Live Transfer Mailing ServiceSmtp About What is Mobile Viewer? Using a SmartphoneKey Features Mobile ViewerSEC Backup Viewer Recommended System Requirements Backup Viewer Stop playing temporarily Product Specification Camera SED-1001R / SED-1005 / SED-1007RUTP  Appendix0C ~ +40C +32F ~ +104F / 20% ~ 85% RH Humidity Mechanical EnvironmentalW102 X H71.7 mm SEB-1020R Product Specification SDE-4001/4004/4005Ntsc 1TB Sata HDD PAL 500GB Sata HDDHdmi PTZ  AppendixPower consumption Details SDE-4001 SDE-4004 SDE-4005 General ElectricalW350 X H44 X D300mm 13.98 X 1.73 X 11.81 inch Mechanical Box Size OuterSDE-5001/5002 Details SDE-5001 SDE-5002 Video Inputs120fps Stream 264CIF Network Monitoring1TB Sata HDD Details SDE-5001 SDE-5002 Internal HDDBudvr Player, SECInclude Player Details SDE-5001 SDE-5002 General Electrical 8Kg Gross weight 12.8Kg Box Size OuterW350 X H44 X D300 mm 13.98 X 1.73 X 11.81 inch SDE-4003/5003 RTP, RTSP, HTTP, CGI USB 2.0, 2 ports Front Sata General ElectricalDC12V Adaptor,4A,100~250VAC, 50~60Hz, 48watt W360 X H44 X D160 mm 14.17 X 1.73 X 6.30 inchesCategory Details Factory Default Default SettingManagement Duration Smtp Troubleshooting By the service personnel Quick start guide backup, searchInternet using the router section in this manual Playback Icon on the launcher to switch to Live mode4CIF2CIFCIF GNU General Public License Open Source License Report on the ProductPreamble How to Apply These Terms to Your New Programs No WarrantyEND of Terms and Conditions Terms and Conditions Conveying Verbatim CopiesConveying Modified Source Versions Acceptance Not Required for Having Copies GNU Lesser General Public License Limitation of LiabilityPage OpenSSL License How to Apply These Terms to Your New LibrariesOriginal SSLeay License Page Correct disposal of batteries in this product Page Sales Network
Related manuals
Manual 2 pages 50.93 Kb