AMX quick start Using Connector Ports on The Mio R-1, IR Code Matrix, Configuration Mode

Using Connector Ports on The Mio R-1

The programming jack is used for communication between the device and KeypadBuilder. The programming jack uses a three-wire, 2.5 mm stereo jack, you can order the programming cable (FG10-817) from AMX if you do not currently possess one. While loading your configuration file make sure the device is situated as such that the batteries will not fall out. The load will fail if your batteries fall out during the process. The Mio communicates at 115200 baud rate.

To download KeypadBuilder Configuration Files:

1.Set the Mio R-1 Download mode to ON. See the Configuration Mode section for details.

2.Flip and turn the Mio R-1 device so that the buttons are facing away from you and the device is upside down.

3.Holding the device in both hands, place your thumbs on the battery door and slide the battery door free.

4.Connect the 2.5 mm stereo plug (male) end of the programming cable (FG10- 817) into the programming jack on the bottom side of the remote device.

5.If necessary, connect the DB-9 end of the programming cable to the female DB-9 connector on the DB-9 extension cable (FG10-727).

6.Connect the female DB-9 terminal end of the extension cable to the port on the back of your computer.

7.Configure the communication parameters in KeypadBuilder.

Programming
jack	Mio R-1

DB-9 connector

Stereo plug male

Keypad device

to PC Cable FG10-817 to cable FG10-727

programming cable

FIG. 3 Connecting The Keypad Device to Your PC

IR Code Matrix

The IR Code emitted depends upon which of the 6 configurable modes is selected. Below is the list of codes for each button within each mode.

IR Code Matrix

Button	Label	Mode 1	Mode 2	Mode 3	Mode 4	Mode 5	Mode 6
1	Power Symbol	9	49	89	129	169	209
2	GUIDE	38	78	118	158	198	238
3	EXIT	37	77	117	157	197	237
4	MENU	31	71	111	151	191	231
5	INFO	39	79	119	159	199	239
6	L	32	72	112	152	192	232
7	M	33	73	113	153	193	233
8	K	34	74	114	154	194	234
9	A	35	75	115	155	195	235
10	SELECT	36	76	116	156	196	236
11	VOL +	24	64	104	144	184	224
12	VOL -	25	65	105	145	185	225
13	CH +	22	62	102	142	182	222
14	CH -	23	63	103	143	183	223
15	LAST	40	80	120	160	200	240
16	MUTE	26	66	106	146	186	226
17	1	11	51	91	131	171	211
18	2	12	52	92	132	172	212
19	3	13	53	93	133	173	213
20	4	14	54	94	134	174	214
21	5	15	55	95	135	175	215
22	6	16	56	96	136	176	216
23	7	17	57	97	137	177	217
24	8	18	58	98	138	178	218
25	9	19	59	99	139	179	219
26	INPUT	29	69	109	149	189	229
27	0	10	50	90	130	170	210

IR Code Matrix (Cont.)

Button	Label	Mode 1	Mode 2	Mode 3	Mode 4	Mode 5	Mode 6
28	ENTER	21	61	101	141	181	221
29	A (Macro 1)	250	250	250	250	250	250
30	B (Macro 2)	251	251	251	251	251	251
31	C (Macro 3)	252	252	252	252	252	252
32	TV (Mode 1)	241	241	241	241	241	241
33	SAT (Mode 2)	242	242	242	242	242	242
34	DVD (Mode 3)	243	243	243	243	243	243
35	CD (Mode 4)	244	244	244	244	244	244
36	AUX (Mode 5)	245	245	245	245	245	245
37	LGHT (Mode 6)	246	246	246	246	246	246
38	STOP B	2	42	82	122	162	202
39	REC J	8	48	88	128	168	208
40	PAUSE C	3	43	83	123	163	203
41	S. REV Z	7	47	87	127	167	207
42	PLAY A	1	41	81	121	161	201
43	S. FWD Y	6	46	86	126	166	206
44	REW E	5	45	85	125	165	205
45	FWD D	4	44	84	124	164	204

Configuration Mode

The configuration mode allows you to set the following device features:

•IR Transmit Mode (38 KHz or 455 KHz)

•Timeout Adjustment

•Download Mode

•Debug Mode

•Battery Type

•LED Awake Brightness

•LED Sleep Brightness

To enter configuration Mode:

1.Press and hold the STOP button and the INPUT button. The two buttons must be pressed within 0.1 seconds of each other and held down for 2 seconds. The device indicates you are now in configuration mode. See below for available modes.

2.Press the EXIT key when you are finished.

Note: Your settings will not be lost in the event your batteries die or are removed.

IR Transmit Mode

Pressing button "1" on the remote toggles the IR transmission mode between 38KHz and 455KHz. The display indicates the current mode.

Timeout Adjustment

Press button "2" on the remote to change the sleep timeout from the default. Each time "2" is pressed, the sleep timeout raises incrementally. The pre-determined sleep timeouts are:

•3 seconds

•6 seconds

•9 seconds

•12 seconds

The display indicates the selected sleep timeout.

Download Mode

Pressing "3" on the remote toggles the Download mode OFF and ON. The Download mode must be ON before you can download a file to the Mio R-1 device. While the Download mode is ON the device will not go to sleep. A power cycle will return the device to Download OFF.

Debug Mode

Pressing button "4" on the remote toggles development mode between ON and OFF. The display indicates the selected mode. In development mode, the display shows the IR code assigned to buttons when pressed.

This mode is useful to the programmer when determining what IR codes are associated to each mode.

Battery Type

Pressing button "6" on the remote toggles the battery type between Normal and Recharge. The display indicates the selected type. The type of battery in the Mio R-1 dictates the battery type you need to set.

LED Awake Brightness

Pressing button "7" on the remote toggles the Power LED brightness mode from LOW to MED and then HIGH. The display indicates the selected mode.

LED Sleep Mode Brightness

Pressing button "8" on the remote toggles the Sleep brightness mode from OFF to LOW and then MED. The Sleep brightness is the state the Mio R-1 assumes while in the charging cradle.

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s). 93-0147 REV: C

4/07

©2007 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX.

AMX reserves the right to alter specifications without notice at any time.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com