Aphex Systems 1788a instruction manual Suitable Hardware, Typical Network Diagrams Router as Base

Page 32

if there are any fixed IP addresses on the LAN, the Router has to be programmed to avoid issuing them to other clients. In other words, there can be no IP address duplications on the LAN. The DHCP Server (or Router) must have enough IP numbers available to handle all DHCP clients on the LAN. There cannot be a firewall splitting up any part of the LAN, but the whole LAN can be inside a firewall. You need to check with your network administrator to be sure ports 1198 and 1199 are present are unlocked. If unreliable results are obtained, then your common network might be overburdened. You should then set up a separate dedicated network for remote control.

4.7 SUITABLE HARDWARE

Purportedly, all networking products are generic. Any brand Router or Switch should work equally well. We have had little trouble using various name brand networking products, but in some cases low priced off-brand boxes were unreliable. For that reason, we recommend using well known equipment brands only. Other than that, you should be able to mix and match network equipment for a successful network.

NOTE: Passive Hubs don’t work at all with a 1788A LAN. Be sure to use only active (self powered) Hubs.

4.8TYPICAL NETWORK DIAGRAMS Router as Base

This is preferred because it puts the Router (and more importantly its reset button) more conveniently near the operating position, just in case it goes out of whack. That’s unlikely, but it’s an imperfect world we live in. Figure 4-2 shows a typical setup using an Internet Router to form the basis of a network. It is also possible to run a single Cat 5 line from the Router to one of the Switches, and then connect the other Switches off that Switch. It should be obvious that you have many options available depending upon the layout of your 1788A constellation.

NOTE: You would need no switches at all if your Router has enough ports handle everything. The main concern would be minimizing the number of Cat 5 runs that are needed to connect preamps at a remote location. Placing a Switch at the remote

location requires only one Cat 5 run from the Router.

Router As DHCP Server Only

Figure 4-3 shows a network configured whereby the Router plays only a DHCP Server role. This may sometimes be preferred in order to reduce any latency or slowness due to the Router’s built-in filtering and firewall features. We have seen no evidence of this being a problem so far, but as installed systems get quite large, it may become a concern.

NOTE: The Router can be attached to any available port of any Switch in the network.

Summary

Detailed Ethernet theory and practice is far beyond the scope of this chapter, but we have tried to make it easy for you to understand the basic networking techniques for connecting a constellation of 1788A’s with their remote controllers. Since all of the preamps, and R/C units are dynamically identified by the DHCP Server, setting up a working network is very easy. It’s almost “plug and play”. If you experience problems with networking 1788A’s and their Remote Controllers, contact Aphex Technical Support for help.

Page 32

Page 31 Page 32
Image 32
Page 31 Page 32
Contents Manual Contents R/C Interface Connectors C OverviewR/C Interfaces Control Language Midi SysExConcept of Banks & Constellations Indirect Midi ControlEthernet LAN Hardware R/C Computer R/CPreset Management About PresetsWide System View Massive Grouping & ControlSoftware Presets Management ExtentsConstellation and Bank Capture/Recall Hardware RecallWRAP-UP Using Midi Procedure for Setting The NumbersDirect Midi Control Determining Channel & Device Numbers Channel & DeviceSetting Up The Controller Understanding Ch, Dev and Net OffsetsConnections Controlling Multiple 1788A’sLimitation Broad Commands & PresetsLearning a Preset Indirect Midi Control Indirect Midi Control ExamplesHardware Hook-up Control AssertionPreset Recall Strategy Expanding the SysEx String4 1788A-R’s Odd Midi I.D Daisy-Chained 1788A-R’sSynchronizing Procedure Multiple Midi ControllersReference Data Parametric Codes & ValuesUseful Conversion Tables General Hexadecimal Conversion TableMidi Control Examples SysEx F0 00 00 38 00 00 00 00 01 2D F7 ExampleSysEx F0 00 00 38 01 00 00 05 04 01 F7 Example SysEx F0 00 00 38 01 00 01 00 01 2D F7 ExampleIt’s easier to it see this way SummaryFront Panel Controls 1788A-R Hadrware RemotePurpose Status LED’s Comm LED’sClip/Limit LED’s Changing the Holdover TimeSecondary Functions Test Tone ButtonsPutting Up a Test Tone Preset Manager Panel Control/Display PanelTaking Control SnapshotsMismatch Errors Edit ModeHow to Take a Live Snapshot EditingEscaping From Edits How to EditEditing Tools Power Unit 1 I/O Located HereBank Selector Midi JacksInstallation More about Using the 1788A-R Setting Up The Midi ChannelAssigning a Bank Initial SyncCoexisting with a Software R/C Multiple Select Group BehaviorHubs & Switches Building a Proper NetworkStandard Parts Networking SpeedRouter As Dhcp Server Only Typical Network Diagrams Router as BaseSuitable Hardware

1788a specifications

Aphex Systems 1788A is a high-performance microphone preamp and A/D converter known for its exceptional sound quality and versatility. This device is widely used in professional recording studios, broadcast facilities, and live sound applications, catering to a range of audio needs from vocals to instruments.

One of the key features of the 1788A is its ability to handle a wide variety of microphone types, including dynamic, condenser, and ribbon microphones. It provides a significant amount of gain, with a range of up to 70dB, allowing it to capture even the faintest of sounds without introducing noise. The flexibility of input options is enhanced by phantom power, which can be activated for condenser mics needing external power.

The Aphex 1788A also integrates advanced A/D conversion technology, providing high-resolution 24-bit audio with sample rates up to 192 kHz. This ensures that audio fidelity is maintained during the recording process. The unit features a dual-path A/D converter, which optimizes the signal for clarity and precision.

The device also incorporates Aphex’s innovative iEqualization processing, allowing users to enhance their recordings with EQ capabilities in real time. The iEqualization feature is particularly beneficial for adjusting the tonal characteristics of the source material, providing a more polished final product.

Another standout characteristic of the Aphex 1788A is its robust build quality. Designed for the rigors of professional use, the unit is housed in a rugged chassis that can withstand the demands of mobile and studio environments alike.

Transporting this device is made easier due to its rack-mountable design, fitting seamlessly into any standard 19-inch rack setup. Additionally, users appreciate the intuitive front-panel controls that facilitate easy adjustments and monitoring of levels.

In terms of connectivity, the 1788A offers multiple outputs, including analog XLR and digital outputs via AES/EBU and S/PDIF connections, making it highly compatible with various audio interfaces and recording systems.

Overall, the Aphex Systems 1788A is a powerful tool that combines exceptional preamp performance with high-quality A/D conversion, making it an ideal choice for audio professionals seeking reliability and superior sound quality in their recordings. Its comprehensive feature set ensures it meets the demands of both studio and live environments, solidifying its reputation as a trusted piece of audio equipment.
Top Page Image Contents