Sunwave Tech SRC-3310/9320 manual Problem Solution

Page 50

SRC-93 SERIES User’s Manual

Problem

Solution

You cannot

Make sure that you have correctly

operate a device

“taught” your device’s remote control to

even after

the SRC-93 SERIES. (page 21)

teaching the

Delete the device data from the SRC-93

device using the

SERIES and carry out the learning

learning function.

function again. (page 25)

 

 

Make sure you did not program more

 

than one remote for a given device.

You see “ERROR”

Make sure you hold the other remote’s

display on the LCD

button down for about 2 seconds.

during the learning

Make sure you did not program more

procedure.

than one remote for a given device.

 

 

Make sure the two remotes are not too

 

close or too far apart and are aiming

 

directly at each other - keep apart

 

between 2~4 inches (5~10cm ).

You see “ERROR”

The button that you pressed has not

display during

been taught. Teach the button using the

operation.

learning procedure. (page 20)

Your VCR will not

As a safety feature on SRC-93 SERIES,

record.

you must press the REC key for 2

 

seconds.

Problems changing

If your original remote requires the ENTER

channels.

key to be pressed after a channel is

 

selected, press the ENTER key to select

 

the channel.

Macro does not

Be sure to aim the SRC-93 SERIES at the

work.

devices while the macro commands are

 

being sent.

 

Macro was not properly set up. Repeat

 

macro set-up procedure. (page 29)

46

Image 50
Contents SRC-9310/9320 031021Preface Table of Contents Controlling Devices Alkaline Battery Introducing the SRC-93 SeriesUnpacking the SRC-93 Series SRC-93 Series FeaturesFollowing list identifies the SRC-93’s key features Identifying Components Front and Rear ViewsFeatures Overview Getting StartedPage Installing Batteries Installing BatteriesBattery Low Indicator Battery Tips and PrecautionsTurning the Touch Screen On Touch Screen PrecautionsTouch Screen Please read the following instructions carefullyRubber Buttons Touch Screen ButtonsMenus Confirm Menu Entry by Pressing NumbersSetup Menu Menu DescriptionDelete Menu Macro MenuChoosing a Device Setting Up the SRC-93 Series to Control a DevicePress and hold the Setup button on Touch Screen Creating a New DevicePress the OK button to confirm Re-Labeling DevicesModifying an Existing Device Changing Touch Screen Layout Press OK to confirm your changes Programming Infrared CodesTouch the button that you wish to change Using Manufacturer Codes There are two ways to program the manufacture codes To use manual entryPower button or Auto button to stop the automatic search To use automatic searchUsing the Learning Function Before Using the Learning FunctionLearning from Another Remote Control Press and hold the Setup button on the Touch Screen Rubber KeysSoftKey To collect unrecognized codes Collecting Unrecognized Infrared CodesAll unrecognized codes should be sent to this address Press and hold the Delete button on the Touch Screen Deleting a Specific KeyDeleting a Device Select the key you want to eraseTo delete a device from the SRC-93 Series follow these steps Select the device you wish to deleteChanging Touch Screen Controlling DevicesSelecting Device to Control Using the AUX Key Controlling the DeviceCreating a Macro Sequence Creating and Using MacrosIntroduction to Macros Set up the macro using the following steps Press OK to save the Macro Using Macros Deleting a MacroSRC-93 Series has the following additional features Other FeaturesUsing Timers Setting Up a New Timer Press and hold the Macro button on the Touch ScreenUse the arrow keys to select the time Using Quick Channel ListsWhen finished press the Exit key to leave the Macro Menu Setting up Quick Channel Lists Press and hold the Delete button on Touch Screen Press Exit when finished and leave the Delete menuDeleting Channels from a Quick Channel List Transmitting System Setup Using Quick Channel ListsUsing Sleep Mode To use sleep modeDate and Clock Press OK when finished Now set the hour, and minutesDisplaying Version Number Enter the year, month, and date firstBacklight On Time Period Power Down Time PeriodUse the arrow keys to set the power down time Use the arrow keys to set the backlight periodBeep Toggling Resetting to Factory DefaultsPress OK to reset the SRC-93 Use the OK button to toggle the beep from on to OFFAppendix a Specifications Model SRC-9310 SRC-9320USB cable Appendix B AccessoriesSLC-2080 Appendix C Troubleshooting Problem SolutionProblem Solution IR Learning