Contec RC-U49C-15+, RT-U49C+ operating instructions Introduction, Before Getting Started

Page 1

CheckMate® IV

Model RT-U49C+

Universal Remote Control

+

-

Programming And Operating

Instructions

To have a clearer idea of the features and capabilities of

your remote control, take a moment to read these

instructions. Save for future reference.

© 2003, CONTEC CORPORATION, Rev. 07/03

1. Introduction

Your CheckMate® IV universal remote control is simple to program, easy to use, and can operate up to four (4) devices, which include:

CABLE

Cable set-top terminals

TV

Televisions

VIDEO

VCR, DVD

AUDIO

Audio receivers, amplifiers, CD players

Before you can use your remote control, it must be programmed (set-up) to operate the above devices.

2. Before Getting Started

Some of the special features and buttons on your remote control are as follows:

Point and Press® Programming

Lets you program your TV, VIDEO, AUDIO devices without codes.. For more information, see Sections 5 and 18.

[ALL]

Turns all of your electronic devices on / off with one button press. [ALL] can even be programmed to automatically tune your TV to its correct output channel. For more information, see Section 8.

[MOVIES], [SPORTS], [NEWS]

Program your favorite channels on the [MOVIES], [SPORTS] and [NEWS] buttons. For more information see Section 9.

[VCR / VOD] Toggle

“Toggles” the VCR buttons between CABLE (Video- On-Demand) and VIDEO (VCR / DVD) functions. For more information, see Section 10.

SmartKeys™

Program multiple button presses on the [CBL] and [TV] buttons. For more information, see Section 15.

[MODE]

Indicates which mode (CBL, TV, VIDEO, AUDIO) the remote is currently operating in by illuminating the power button. To change to a different mode, press [MODE], then the power button for the electronic device you wish to operate. For more information, see Sections 10, 11, 12, 13, 16, 18.

Memory Guard™

Eliminates reprogramming after battery changes.

Time Out

Shuts remote off if any button is pressed and held for 30 seconds. This extends battery life in the event the remote becomes lodged under or between heavy objects.

3. Installing / Replacing Batteries

Install two (2) new “AA” alkaline batteries as indicated by the diagram in the battery compartment.

When the batteries become low and need to be replaced, the [CBL], [TV], [VIDEO], [AUDIO] buttons will not illuminate normally or at all during use.

When this happens, replace the existing batteries with two (2) new “AA” alkaline batteries to restore normal operation to the remote control.

4. Programming Your Cable Set-Top Terminalu

Your CheckMate® IV remote is pre-programmed to operate the Scientific-Atlanta Explorer®, Pioneer Voyager® and Pace digital set-top terminals.

To operate a different cable set-top terminal, look up the brand and model in the Cable Setup Code list. If you are not sure of your brand and model, contact your cable company.

1.Press [SELECT], then [MUTE] together until the power / mode buttons illuminate in slow-rotation (i.e. CBL Æ TV Æ VIDEO Æ AUDIO Æ CBL…).

2.From the Cable Setup Code list, locate the 3-

Image 1
Contents Introduction Installing / Replacing BatteriesBefore Getting Started Programming Your Cable Set-Top TerminaluDL4, DPV, DQNV, Dpbb Cable Setup CodesProgramming Your TV, VIDEO, Audio Devices Code-Entry ProgrammingProgramming Your TV / VCR Combination TV Setup Codes415 416DVD Setup Codes VCR Setup Codes414 Resetting the ALL Button Audio Setup CodesALL Button MOVIES, SPORTS, News Buttons Exit Settings Guide Info FAVOperating Your Cable Set-Top Terminal ALL CBL Video AudioOperating Your TV Programming Volume ControlOperating Your Video VCR or DVD Device Operating Your Audio DeviceAdditional Programming Information, Troubleshooting, Tips Mode LockTV / VCR Input Frequently Used Terms Troubleshooting / Tips2003, Contec Corporation Buttons are operating Cable Video Using Your RT-U49C+ Remote Control