Hitachi 53SBX10B AV1, AV2, AV3, or CD, TAPE, AMP buttons, Channel selector buttons, Sleep button

Page 21

HOW TO USE THE GENIUS REMOTE TO CONTROL YOUR TV

AV1, AV2, AV3, or CD, TAPE, AMP buttons

When pressed, each of these buttons will blink to indicate the remote is in Audio/Video mode. (see page 30)

NOTE:

Your remote control SOURCE WIZARD buttons are either labeled as AV1, AV2 and AV3, or

CD, TAPE, and AMP.

 

If your remote control SOURCE WIZARD buttons are labeled as AV1, AV2, and AV3, please program your Audio/Video

 

components as follow for best performance. Use AV1 to program your CD brand. Use AV2

to program your TAPE

 

brand, and use AV3 to program your AMPLIFIER/RECEIVER brand.

 

AV1-Use for CD brand AV2-Use for TAPE brand

AV3-Use for AMPLIFIER/RECEIVER brand.

SOURCE WIZARD

AV1

AV2

DVD

AV3

CHANNEL selector buttons

CHANNEL selector buttons are used to set FAMILY FAVORITES, CHANNEL MEMORY, etc.

Enter one, two, or three numbers to select channels. Enter 0 first for channels 1 to 9, or simply press the single digit channel you wish to tune then wait a few seconds for the TV to tune. For channels 100 and above, press the 1 button, wait until two dashes appear next to the channel display on your TV, then enter the remaining two numbers using the number buttons.

Channel selection may also be performed by pressing CH up ( ) or down ( ).

NOTE: The TV may not receive some channels if you are not in the correct SIGNAL SOURCE mode. (see page 35)

SLEEP button

Press this button to display the sleep timer in the lower left corner of the screen. Every subsequent press of this button will add 15 minutes to this timer, up to a maximum of three hours. Once set, use STATUS when you want to view time remaining. If the SLEEP button is pressed while the timer is set, it will reset to the original condition.

LAST CHANNEL (LAST CH) button

Use this button to select between the last two channels viewed. (Good for watching two sporting events, etc.)

Ant A 10

LAST CH

Ant A 39

INPUT button

Press this button to select from the four input sources and the two antenna sources.

INPUT

HELP button

 

 

 

Stereo

Ant A 28

 

ST/SA

TAKA

 

 

 

 

 

 

 

Ant B 32

TAJK

INPUT

INPUT

Video:1

VID1

Video:4

VID4

INPUT

INPUT

Video:2

VID2

Video:3

VID3

INPUT

Press this button when a menu is displayed to view HELP text, which gives a description of the displayed menu. The HELP text will be displayed every time a MENU is displayed, until this button is pressed again.

PIX button

Press this button repeatedly to direct access THEATER MODE between Sport, News, Movie, and Music.

MENU button

The MENU button will start the On-Screen Display.

EXIT button

When in MENU mode, this button will exit all On-Screen Displays.

21

Image 21
Contents 53SBX10B Safety Points YOU should Know about Your Hitachi Television Important Safety InstructionsPublic Viewing of Copyrighted Material Prevention of Pattern BurnVOL AccessoriesAntenna HOW to SET UP Your NEW Hitachi Projection TVLocation ViewingAntenna Connections to Rear Jack Panel HOOK-UP Cables and ConnectorsFront Panel Controls Remote Control sensor Power lightPerfect Picture sensor Magic FocusInput Output Front Panel Jacks and ConnectionsMonitor OUT Rear Panel JacksComponent Y-PBPRInputs Rear Panel Connections Typical FULL-FEATURE SetupTips on Rear Panel Connections Tips on Rear Panel ConnectionsConnecting External Audio Amplifier Connecting External Audio SourcesBefore Operating External Video Source Connecting External Video SourcesVCR VCR or Laserdisc Player Hitachi Model or Similar Model Back Connecting a Component Source to Video 4 Y-PBPRLight Button Genius Remote ControlHOW to USE the Genius Remote to Control Your TV Cable CBLSET-TOP-BOX STB Channel selector buttons AV1, AV2, AV3, or CD, TAPE, AMP buttonsSleep button Last Channel Last CH buttonThumb STICK/SELECT button VOLUME, Mute buttonStatus button PICTURE-IN-PICTURE buttonsSingle Mode PIP PICTURE-IN-PICTURE PIPPIP button PIP Mode button PICTURE-IN-PICTURE Surf Mode PIPSwap button SingleFreeze button With PIP OFF Freeze button With PIP onSingle Freeze Strobe FreezeOperating the precoded function for your VCR Using the Remote to Control VCR FunctionsPrecoded VCR Buttons Exclusive TV ButtonsOperating the precoded function for your cable box Using the Remote to Control Cable BOX FunctionsCable CBL button Precoded Cable BOX buttonsPrecoded SET-TOP-BOX buttons SET-TOP-BOX STB buttonUsing the Remote to Control DVD Functions Operating the precoded function for your DVD playerPrecoded DVD Buttons Precoded AUDIO/VIDEO Buttons AV1, AV2, AV3 ButtonsVCR BRAND. . . . . . . . . . . . . . . . . Code AUDIO/VIDEO CodesUltratec OSD Setup Customize Video Audio Menu Language SET UPMenu To Menu Bar To Quit I t Signal SourceAuto Channel SET Erase Channel MemoryChannel List Clock SET Magic Focus Channel ID CustomVideo ID Family Favorites Menu Family Favorites Operation Customize Use number buttons to enter Parental ControlMenu To Menu Bar To Quit Event ProgAuto Link Display Closed CaptionMode ChannelVideo Contrast Brightness Color Tint Sharpness ResetColor Temperature Advanced SettingsPerfect Picture Auto ColorBass AudioTreble BalanceAuto Noise Cancel MTS ModePerfect Volume Internal SpeakersTheater Modes TheaterSurround OFF SurroundDo not Care of Your Hitachi Projection TV Your Remote Control¥ Ignition Noise Reception ProblemsUseful Info SymptomsFeatures SpecificationHome Electronics Division HitachiQR47651