Mitsubishi Electronics SL2U XL1X user manual Feature, Signal, Clamp Position

3FEATURE

MENU POSITION ..... Use to select the position of the menu on the screen,					opt.	XGA60
(upper left) or (lower right).
	FEATURE
EXPAND MODE .... Select the mode for enlarging screen. See page 20.
				MENU POSITION		1.
FRAME POSI. .... Sets the position of sub screen. See page 20.
AUDIO MODE .... Select COMPUTER to output the sound which is inputted to		A		EXPAND MODE		1.
			A
		A		FRAME POSI.		3.
the audio input terminal when COMPUTER is selected as the			A
				AUDIO MODE		COMPUTER
source. Select VIDEO to output the sound which is inputted						VIDEO
	?			VIDEO SIGNAL		AUTO
to the audio input terminal when VIDEO is selected as the
source. Select COMPUTER VIDEO mode to always output				SCART INPUT		OFF
				ANAMORPHIC		OFF
the sound which is inputted to the audio input terminal.
				3D CineView		ON
Select MUTE not to output the sound at all.
VIDEO SIGNAL .... When AUTO is selected, the appropriate video format is		A Ë		LANGUAGE		English
automatically selected depending on the input signal. If the				RESET ALL		OK
image isn’t displayed correctly, select the desired video format manually.

SCART INPUT ... Select ON when connecting with a device equipped with the SCART terminal that can output RGB signal. SCART terminal is used mainly in Europe. Select OFF normally.

ANAMORPHIC ... Select the desired position, UPPER, CENTER or LOWER when playing DVD discs containing data of letterboxed images.

3D Cine View ...... Select ON for high quality video image. Select ON normally.

LANGUAGE ....... Use to select the language used in the menus. (					/ English / Español / Deutsch / Français
/ Italiano /	/	/	/	)

RESET ALL ........ Use to reset the MENU settings (except LANGUAGE).

•When SCART is set to ON, nothing is output to the external monitor.

•When SCART is set to ON, normal computer signals are not projected.

•Use SCART-Mini D-SUB 15P cable (option), when connecting with AV device equipped with the SCART terminal.

•Some AV devices equipped with the SCART terminal may not be compatible with the projector.

•When VIDEO SIGNAL is set to AUTO, the image may not be projected with correct colors. Change the setting of VIDEO SIGNAL depending on the input signal in such cases.

•When 3D Cine View is switched from OFF to ON, you can check the motion detection operation about three seconds. The buttons on the remote control don’t work during this period, which isn’t a failure.

4 SIGNAL
		opt.
MEMORY CALL ....	Use to select AUTO, USER 1 or USER 2. See page 18.		XGA60
HORIZ. POSITION ....	Use to adjust the horizontal position of the image.	SIGNAL
VERT. POSITION	Use to adjust the vertical position of the image.	A U MEMORY CALL	AUTO
FINE SYNC	Use to synchronize the projector with PC input signals so that	HORIZ. POSITION	0
	the image is not blurred.	VERT. POSITION	0
TRACKING	Use to avoid image noise such as wide stripes.	FINE SYNC.	0
COMPUTER INPUT	The unit adjusts itself automatically when connected to a DVD	TRACKING	0
	player with a component video output (Y, CB, CR). In the case ( Y,	COMPUTER INPUT	RGB
		RRGGBB
	PB, PR). In the case the projector is connected to equipment that	HOLD	AUTO
	includes RGB output terminal, adjust to RGB mode.	USER MEMORIZE	DELETE DEFAULT
HOLD	Adjusts the image when flagging occurs near the top of the
	screen.

5 SIGNAL - USER (Normally, there is no need for adjustments.)

CLAMP POSITION/	SIGNAL-USER
	CLAMP POSITION	0
CLAMP WIDTH ..... If you use something similar, the brighter colors of the projected
	CLAMP WIDTH	0
image may become blurred. In this case, adjust CLAMP
	HORIZ. PIXELS	0
POSITION or CLAMP WIDTH.
HORIZ.PIXELS .. Use to adjust the width of the image. The image size grows	VERT. LINES	0
wider as the number increases. (Adjust to the horizontal pixels	VERT. SYNC.	AUTO
of the input signal for normal setting.)	SHUTTER(U)	0
VERT.LINES ...... Use to adjust the height of the image. The image size grows	SHUTTER(L)	0
higher as the number increases. (Adjust to the vertical lines of	SHUTTER(LS)	0
the input signal for normal setting.)	SHUTTER(RS)	0

VERT.SYNC. ...... Use to adjust the image when its motion does not run smoothly. Select AUTO for normal

setting.

SHUTTER(U) ..... Use to adjust the image when the noise etc. appears on top part of image.

SHUTTER(L) ...... Use to adjust the image when the noise etc. appears on bottom part of image.

SHUTTER(LS) .... Use to adjust the image when the noise etc. appears on left side of image.

SHUTTER(RS) ... Use to adjust the image when the noise etc. appears on right side of image.

•When the setting of the SIGNAL-USER menu is changed, the image may not be displayed correctly. In this cace, select DEFAULT in the SIGNAL menu, and press the ENTER button.

ENGLISH

EN – 17