Mitsubishi Electronics HC1500 user manual Preparing your projector, Checking accessories

Page 6

Preparing your projector

Checking accessories

The following accessories are provided with this projector. Check to be sure that all of the accessories are packed in the package.

Cables

 

Power supply parts

Mini D-SUB

D-SUB 9-pin

 

15-pin

 

Mini D-SUB

8-pin

 

15-pin

 

RGB cable for PC

RS-232C cable

Power cord

(246C521-10)

(246C508-10)

(246C483-10)

Used for projector control by computer.

Remote control parts

 

Others

 

 

• Lens cap (Attached to the projector)

• User manual/Quick Start up (English only) (871D488-50)

CD-ROM (with User manual) (919C154-40)

• Safety manual/Quick Start up (871D489-40)

Remote control

R03 (Size-AAA)

(290P133-30)

battery (two)

Important:

• The attached power cord is to be used exclusively for this product. Never use it for other products.

Inserting the batteries into the remote control

1

1.

Remove the back lid of the remote control.

2.

Check the polarity (+), (-) of the batteries, and set them

 

3

correctly, inserting their (-) side first.

 

 

• If the battery is inserted from the (+) side first, inserting

 

 

the (-) side is difficult because the coil spring end hits

 

 

on the battery side. If the battery is forced in this way,

 

2

the outer label of the battery may get ripped and it may

 

cause a short-circuit and heating.

 

 

 

3.

Attach the back lid.

 

Important:

 

Use two size-AAA batteries (R03).

 

Replace the two batteries with new ones when the remote

 

 

control is slow to respond.

Caution:

Use of a battery of wrong type may cause explosion.

Only Carbon-Zinc or Alkaline-Manganese Dioxide type batteries should be used.

Dispose of used batteries according to your local regulations.

Batteries may explode if misused. Do not recharge, disassemble, or throw them in fire.

Be sure to handle the batteries according to the instructions.

Load the batteries with its positive (+) and negative (-) sides correctly oriented as indicated on the remote control.

Keep batteries out of reach of children and pets.

Remove the batteries, if the remote control is not used for a long time.

Do not combine a new battery with an old one.

If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes in contact with your eyes, rinse them with water and then consult your doctor.

EN-6

Image 6
Contents HC1500 Risk of Electric Shock Do not Open Contents Important safeguards Important safeguards Checking accessories Inserting the batteries into the remote controlPreparing your projector Preparing your projector OverviewControl area Terminal panel Adjustment foot Front Lamp cover Adjustment feet Rear Remote controlUsing the picture quality adjusting buttons Bottom sideReception angle Using the remote controlOperational range of the remote control Front of projector Rear of projectorBasic setup Setting up your projectorSetting up the screen Adjusting the projection angleTo cancel the menu Setting up your projectorWith the Installation menu Trigger terminalWhen the aspect ratio of the screen is When the aspect ratio of the image isScreen size and projection distance Basic home theater system connection Connecting the projector to video equipmentViewing video images PreparationWhen a TV tuner or VCR is connected Connecting to a video player, etcConnecting to a DVD player or Hdtv decoder Viewing video imagesConnection for video equipment having an Hdmi terminal Connection for video equipment having a DVI-D terminalPlugging in the power cord Projecting images When projected images are distorted to a trapezoid To stop projectingFollowing cases With the remote control Setting the aspect ratioHow to change the settings With the Feature menuViewing computer images Connecting the projector to a computerPlugging the power cord For analog connectionViewing computer images Projecting imagesWhen connecting to a notebook computer Example of the setting procedure for external outputAuto Position button Menu operation Menu operation How to set the menusAvailable settings in the menus Image menuInstallation menu Feature menuTo enable the stored image quality settings Signal menuTo store the settings AV memoryTo adjust the color Color and Tint Adjusting projected imagesTo adjust the brightness Contrast and Brightness To sharpen or soften the projected image SharpnessAbout color temperature Adjusting projected imagesTo adjust the tone of white Color Temp To adjust the ratio of change in brightness Gamma ModeTo adjust the vertical position LPFTo enable the password function Advanced featuresPassword function To cancel the password functionInterval of lamp replacement Replacing the lampReset of the lamp operation time Cleaning of the projector and the ventilation slotsCleaning of the lens Replacing the lampTroubleshooting No image appears on the screen ProblemSolution Problem Solution TroubleshootingNo image appears on the screen Problem Solution Images are not displayed correctlyImages are not displayed correctly Problem Solution Others Problem SolutionNormal condition IndicatorsPower Status Condition Possible Solution Abnormal conditionDimension drawings unit mm SpecificationsSpecifications ConnectorsReplacement part Option/not included in the box VLT-HC910LPMitsubishi Projector Contact Information