Mitsubishi Electronics HC1500 Adjusting projected images, To adjust the tone of white Color Temp

Page 28
GAMMA MODE-USER1

Adjusting projected images (continued)

To adjust the tone of white (COLOR TEMP.):

You can select a preset color temperature (white tone) using the menu. (See page 24 for menu setting.)

1.

Display the IMAGE menu.

2.

Select COLOR TEMP. by pressing the or button.

3.

Select your desired color temperature by pressing the or button.

To cancel the menu:

4. Press the MENU button.

To adjust the tone of white (To customize the color temperature):

To customize (and store) the color temperature to your preference, carry out the following procedure. (See page 24 for menu setting.)

1.

Select COLOR TEMP. in the IMAGE menu.

2.

Press the

or

button to select USER

 

.

 

3.

Press the ENTER button.

4.

Press the

or

button to select the desired item.

5.

Press the

or

button to adjust the selected item.

6.

Repeat steps 4 and 5 for optimum adjustment results.

To cancel the menu:

7. Press the MENU button.

To enable the stored color temperature:

1. Select USER by pressing the COLOR TEMP button on the remote control.

About color temperature

COLOR TEMP.-USER

CONTRAST R

0

 

 

CONTRAST G

0

 

 

CONTRAST B

0

 

 

BRIGHTNESS R

0

 

 

BRIGHTNESS G

0

 

 

BRIGHTNESS B

0

 

 

There are different kinds of white color. Color temperature is a way to show the differences in white. White of which temperature is low appears reddish. When the color temperature rises, white appears bluish. For example, you can change the color temperature using the following procedures.

To rise the color temperature: Increase the CONTRAST B (blue) and decrease the CONTRAST R (red).

To reduce the color temperature: Decrease the CONTRAST B (blue) and increase the CONTRAST R (red).

•If you set all of CONTRAST R, G, and B to negative values, the original brightness of the image can’t be obtained even when you maximize CONTRAST in the IMAGE menu.

To adjust the ratio of change in brightness (GAMMA MODE):

You can select a preset gamma mode using the menu. (See page 24 for menu setting.)

1.

Display the IMAGE menu.

2.

Select GAMMA MODE by pressing the or button.

3.

Select your desired gamma mode by pressing the or button.

To cancel the menu:

4. Press the MENU button.

To adjust the original ratio of change in brightness (To customize the gamma mode):

To customize (and store) the gamma mode to your preference, carry out the following procedure. (See page 24 for menu setting.)

1.

Select GAMMA MODE in the IMAGE menu.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

REFERENCE

VIDEO

 

2.

Press the

or

button to select USER1

 

or USER2

 

.

 

 

 

 

 

 

 

 

 

HIGH

 

0

 

3.

Press the ENTER button.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MID

 

0

 

4.

Press the

or

button to select REFERENCE.

 

 

 

 

 

 

 

 

 

LOW

 

0

 

5.

Press the

or

button to select basic gamma curve.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Generally, select the most preferable gamma curve from the preset gamma curve.

 

 

6.

Press the

or

button to select the desired item.

 

 

 

 

 

 

HIGH

: Use to adjust the gradation of the bright scenes.

 

 

 

 

 

 

MID

: Use to adjust the gradation of the medium brightness scenes.

 

 

 

 

 

 

LOW

: Use to adjust the gradation of the dark scenes.

 

 

 

 

 

7.

Press the

or

button to adjust the selected item.

 

 

 

 

 

8.

Repeat steps 6 and 7 for optimum adjustment results.

 

 

 

 

 

To cancel the menu:

9. Press the MENU button.

To enable the stored gamma mode:

1.Select USER1 or USER2 by pressing the GAMMA button on the remote control.

• Change in the brightness may be hard to recognize in some images.

EN-28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents
HC1500 Risk of Electric Shock Do not Open Contents Important safeguards Important safeguards Inserting the batteries into the remote control Checking accessoriesPreparing your projector Overview Preparing your projectorControl area Terminal panel Remote control Using the picture quality adjusting buttonsAdjustment foot Front Lamp cover Adjustment feet Rear Bottom sideUsing the remote control Operational range of the remote controlReception angle Front of projector Rear of projectorSetting up your projector Setting up the screenBasic setup Adjusting the projection angleSetting up your projector With the Installation menuTo cancel the menu Trigger terminalWhen the aspect ratio of the image is When the aspect ratio of the screen isScreen size and projection distance Connecting the projector to video equipment Viewing video imagesBasic home theater system connection PreparationConnecting to a video player, etc Connecting to a DVD player or Hdtv decoderWhen a TV tuner or VCR is connected Viewing video imagesConnection for video equipment having an Hdmi terminal Connection for video equipment having a DVI-D terminalPlugging in the power cord Projecting images To stop projecting When projected images are distorted to a trapezoidFollowing cases Setting the aspect ratio How to change the settingsWith the remote control With the Feature menuConnecting the projector to a computer Plugging the power cordViewing computer images For analog connectionViewing computer images Projecting imagesExample of the setting procedure for external output When connecting to a notebook computerAuto Position button Menu operation How to set the menus Available settings in the menusMenu operation Image menuInstallation menu Feature menuSignal menu To store the settingsTo enable the stored image quality settings AV memoryAdjusting projected images To adjust the brightness Contrast and BrightnessTo adjust the color Color and Tint To sharpen or soften the projected image SharpnessAdjusting projected images To adjust the tone of white Color TempAbout color temperature To adjust the ratio of change in brightness Gamma ModeTo adjust the vertical position LPFAdvanced features Password functionTo enable the password function To cancel the password functionInterval of lamp replacement Replacing the lampCleaning of the projector and the ventilation slots Cleaning of the lensReset of the lamp operation time Replacing the lampNo image appears on the screen Problem TroubleshootingSolution Troubleshooting No image appears on the screen Problem SolutionProblem Solution Images are not displayed correctlyImages are not displayed correctly Problem Solution Others Problem SolutionIndicators Power Status Condition Possible SolutionNormal condition Abnormal conditionDimension drawings unit mm SpecificationsConnectors Replacement part Option/not included in the boxSpecifications VLT-HC910LPMitsubishi Projector Contact Information