One for All URC 4081, URC 4080 manual Checking the Codes, Press CBL/SAT once, Then release SET

Page 13

CHECKING THE CODES

If you have set up the One For All 4-Device Video Expert remote control using the Searching For Your Code proce- dure, you may need to find out which four-digit code is operating your equipment. For example, to find out which code is operating your TV:

1.Turn on your TV.

2. On the remote control, press TV once.

Press and hold SET until the LED blinks twice, then release SET.

3. Enter 9 - 9 - 0. The LED will blink twice.

4. To view the code for the first digit, press 1 once. Count the number of LED blinks (e.g., 3 blinks

=3) and write down the number in the left- most TV Code box below.

NOTE: If a code digit is “0”, the LED will not blink.

5.Repeat step 4 three more times for remaining

digits. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit. Finish writing down the code in the TV Code boxes below.

6.To check for the codes of your other compo- nents, repeat steps 1 through 5, but substitute the appropriate key (i.e., DVD, VCR, or CBL/SAT) for the (DVD/LD,VCR, or Cable/Satellite) com- ponent you are checking. Write down the codes in the appropriate boxes below.

TV Code

DVD (or LD) Code

VCR Code

Cable/Satellite Code

PROGRAMMING THE MASTER POWER KEY FOR ALL ON/OFF

With the One For All 4-Device Video Expert, you can program the M. POWER key to turn your TV,VCR, DVD, and Cable (or Satellite) components on and off with the press of one button.

1. On the remote control, press and hold SET until the LED blinks twice, then release SET.

2. Enter 9 - 9 - 5. The LED will blink twice.

3. Press M.POWER once.

4.Enter the following sequence*:

a. Press TV once. b. Press VCR once. c. Press DVD once.

d. Press CBL/SAT once.

5.

Press and hold SET until the LED blinks twice,

 

then release SET.

6.Now, when you press M.POWER once, the remote control will direct power to your TV, VCR, DVD (or LD) player, and Cable/Satellite component and leave the remote control in the TV mode.

*NOTE: If you do not want all of your equipment to power up all of the time, you can shorten step 4 to include only those devices you want to turn on or off. For example, to just power up your TV and DVD (or LD) player, enter the following sequence for step 4:

a.Press TV once.

b.Press DVD once.

Now when you press M.POWER once, the One For All 4-Device Video Expert remote control will only direct power to your DVD (or LD) player and TV, and still leave the remote control in the TV mode.

24

25

Image 13
Contents Video Expert Introduction Table of ContentsUse the F1, F2, F3, or F4 keys To program macros. Also see Features and FunctionsKey Charts Installing BatteriesIf available Programming TV Control Setup Codes for TVsTV Brand Write your TV code in the boxes below for future referenceKTV KECLXI MGAProgramming VCR Control Setup Codes for VCRsVCR Brand Write your VCR code in the boxes below for future referenceSTS Programming TV/VCR Combo Control Setup Codes for TV/VCR CombosCable Converter Brand Satellite Receiver Brand Setup Codes for Cable ConvertersABC NSCProgramming DVD Player Control Setup Codes for Satellite ReceiversHTS Setup Codes for LD Players Setup Codes for DVD PlayersSearching for Your Code Press SET once to lock in the codePress CBL/SAT once Checking the CodesThen release SET To change Volume Lock to the CBL/SAT mode Changing Volume LockTo change Volume Lock to the VCR mode To change Volume Lock to the DVD modeUsing Keymover Using the Menu KEYChanging Volume Lock To Unlock Volume LockOr 0 -1- 1 if access is over 100 channels Using MacrosProgramming a Favorite Channel Clearing a MacroLED will blink twice An Example Video ConfigurationAn Example Video Configuration TroubleshootingPart No. URC4080 Additional Information